journal article·2024-05Open access

Research on the strengthening mechanism of Nb–Ti microalloyed ultra low carbon IF steel

Yaxu Zheng, Kun Wang, Qin Yang, Yu Lin, Liguang Zhu, Xiaoyan Wu, Baochen Han, Bo Wang, Di Zhang, Jie Feng, Ruifang Cao

Abstract

Interstitial free (IF) steels are characterized by their interstitial free ferritic matrix due to addition of micro-alloying elements that draw carbon and nitrogen out of matrix to form carbonitrides. The IF steels typically have excellent deep drawing ability, certain mechanical strength, and high plastic deformation performance. In this paper, the microstructure evolution and carbides precipitation behavior during the hot rolling, cold rolling and annealing processes have been studied using both experimental and thermodynamic and kinetic modeling approaches. The strengthening mechanism of Nb-Ti microalloyed IF steel has been investigated. The results of the thermodynamic simulation indicates that the addition of Nb into Ti bearing IF steel promotes recrystallization at 900 °C, leading to fine recrystallized grains. Due to the recrystallization of austenite during the final rolling process, Nb-Ti microalloyed hot rolled plates exhibit finer grain size, fewer substructures, and lower dislocation density compared to the hot rolled plates containing only Ti. Building upon the initial fine and uniform structure, Nb-Ti microalloyed steel maintains a refined structure after undergoing cold rolling and annealing. The study of the carbides precipitation behavior suggests that TiN precipitates at high temperature above 1100 °C, while a substantial amount of (Nb,Ti)C and TiC precipitate at about 900 °C in Nb-Ti and Ti bearing steels, respectively. There is no significantly difference between the amount of carbides in steels hot deformed at 900 °C and in the hot rolled plates, indicating that the carbides mainly precipitate during the hot rolling process. There are negligible carbides precipitated during the coiling process at 600 °C. In Nb-Ti containing steel, Nb and Ti in solid solution are significantly reduced due to the large amount precipitation of (Nb,Ti)C during the final rolling process. The reduction of solid solution Nb effectively promotes the recrystallization of austenite. Therefore, the grains of hot-rolled, cold-rolled, and annealed strips are refined. In addition, there are more small size carbides in Nb-Ti bearing steel than that in Ti bearing steel. Therefore, the higher strength of Nb-Ti steel is mainly from the strengthening effect of grain refinement and carbides precipitation.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Microstructural evolution of IF-steel during cold rolling10.1016/j.actamat.2003.10.040 ↗
2. A study of the heterogeneity of plastic deformation in IF steel by EBSD10.1016/j.msea.2012.03.068 ↗
3. Microstructural development during warm rolling of an IF steel10.1016/S1359-6454(97)00170-5 ↗
4. Mathematical modelling of the stress-strain curves of Ti-IF steel at high temperature10.1016/j.jmatprotec.2005.06.072 ↗
5. Recrystallisation of Ti IF steel investigated with electron backscattering pattern (EBSP)10.2355/isijinternational.36.1046 ↗
6. Intermetallic compounds in Al 6016/IF-steel friction stir spot welds10.1016/j.msea.2010.03.097 ↗
7. Experimental study of deep drawability of hot rolled IF steel10.1016/S0924-0136(02)00230-3 ↗
8. A study of the recrystallization of an IF steel by kinetics models10.1016/S0921-5093(01)01715-4 ↗
9. Effect of cooling rate on phase transformation kinetics and microstructure of Nb-Ti microalloyed low carbon HSLA steel10.1007/s13632-022-00864-9 ↗
10. Effect of high Ti contents on austenite microstructural evolution during hot deformation in low carbon Nb microalloyed steels10.3390/met10020165 ↗
11. Effect of Nb on inclusions and phase transformation in simulated high heat input coarse-grain HAZ of Nb/Ti low carbon microalloyed steel10.1016/j.matchar.2022.111966 ↗
12. Effect of Nb on microstructure and mechanical properties between base metal and high heat input coarse-grain HAZ in a Ti-deoxidized low carbon high strength steel10.1016/j.jmrt.2022.03.150 ↗
13. Determination of non-recrystallization temperature for niobium microalloyed steel10.3390/ma14102639 ↗
14. Quantitative analysis of microstructures and strength of Nb-Ti microalloyed steel with different Ti additions10.1007/s11661-020-05700-9 ↗
15. Effects of Ti microalloying on the microstructure and mechanical properties of acicular ferrite casting steel for high-speed railway brake discs10.1016/j.msea.2022.144125 ↗
16. Effect of deformation sequence and coiling conditions on precipitation strengthening in high Ti-Nb-microalloyed steels10.1007/s11661-022-06670-w ↗
17. Hot deformation behavior, dynamic recrystallization mechanism and processing maps of Ti-V microalloyed high strength steel10.1016/j.jmrt.2023.06.195 ↗
18. Effect of Nb, Ti microalloying on hot deformation behavior of high strength steel
19. Microstructural evolution, coarsening behavior of precipitates and mechanical properties of boron bearing steel 25CrMoNbB during tempering10.1016/j.msea.2017.11.115 ↗
20. Microstructure evolution and carbide precipitation behavior of microalloyed TS800TB steel during hot rolling and coiling processes10.1016/j.msea.2022.142902 ↗
21. Dissolution and precipitation behaviors of boron bearing phase and their effects on hardenability and toughness of 25CrMoNbB steel10.1016/j.msea.2017.06.068 ↗
22. Effect of compound addition of Nb-B on hot ductility of Cr-Mo alloy steel10.1016/j.msea.2018.01.001 ↗
23. Gan · 2019
24. Yang · 2013
25. Yang · 2019
26. Ma · 2010
27. Yong · 2006
28. Effect of cold-rolling deformation and rare earth yttrium on microstructure and texture of oriented silicon steel10.1515/htmp-2022-0258 ↗
29. In-situ EBSD study of deformation behavior of retained austenite in a low-carbon quenching and partitioning steel via uniaxial tensile tests10.1016/j.matchar.2016.06.020 ↗
30. Quantitative phase analysis of martensite-bainite steel using EBSD and its microstructure, tensile and high-cycle fatigue behaviors10.1016/j.msea.2020.139375 ↗
31. Quantification of complex-phase steel microstructure by using combined EBSD and EPMA measurements10.1016/j.matchar.2018.05.038 ↗
32. Influence of M23C6 carbides on the heterogeneous strain development in annealed 420 stainless steel10.1016/j.actamat.2020.08.072 ↗
33. Digital identification scheme for steel microstructures in low-carbon steel10.1016/j.matchar.2017.05.021 ↗