journal article·2023-11Open access

Dynamic recrystallization behavior of selective laser melted 316L stainless steel

Zahra Abbasi, Hamid Reza Abedi

Abstract

The present work deals with the hot deformation behavior of selective laser melted 316L stainless steel with an emphasize on the involved recrystallization mechanisms. Toward this end, a series of hot compression test have been conducted in the temperature range of 700–1000 °C under the various strain rates of 0.001, 0.01 and 0.1s−1. The flow pattern analysis through Jonas-Poliak method verifies the occurrence of dynamic recrystallization in whole investigated temperature range. The intensified substructure development and continuous recrystallization is identified as the main softening mechanism in the course of thermomechanical processing. This causes appearance of a broad peak and low softening fraction in corresponding flow curves. The cellular substructure in the as-printed state facilitates low-angle into high-angle boundaries conversion, which provide a proper condition for the occurrence of continuous mechanisms and increases the rate of recrystallization. However, detailed investigation of the sub-boundary maps indicates the contribution of discontinuous and geometric dynamic recrystallization mechanisms. Dynamic recrystallization causes substantial refinement; and the percentage of the grain holding size lower than 10 μm increases from 2 % in printed microstructure to 16.8 % and 24 % in the microstructure deformed at 700 and 1000 °C.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Forming · Additive Manufacturing Materials and Processes · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (66)

Show source-provided references
1. Celik · 2017 · vol. 17
2. Plastic deformation and creep damage evaluations of type 316 austenitic stainless steels by EBSD10.1016/j.matchar.2010.05.006 ↗
3. Microstructure and mechanical properties relationship of additively manufactured 316L stainless steel by selective laser melting10.1051/epjn/2019051 ↗
4. Hardened austenite steel with columnar sub-grain structure formed by laser melting10.1016/j.msea.2014.12.018 ↗
5. Effects of strain rates and twins evolution on dynamic recrystallization mechanisms of austenite stainless steel10.1016/j.msea.2019.138044 ↗
6. Hierarchical evolution and thermal stability of microstructure with deformation twins in 316 stainless steel10.1016/j.msea.2017.03.073 ↗
7. Microstructure and mechanical properties of AISI 316L produced by directed energy deposition-based additive manufacturing: a review10.3390/app10093310 ↗
8. Orientation-dependent deformation behavior of 316L steel manufactured by laser metal deposition and casting under local scratch and indentation load10.3390/ma13071765 ↗
9. 316L stainless steel mechanical and tribological behavior—a comparison between selective laser melting, hot pressing and conventional casting
10. Review of selective laser melting: materials and applications10.1063/1.4935926 ↗
11. On the anisotropic mechanical properties of selective laser-melted stainless steel10.3390/ma10101136 ↗
12. Study of mechanical properties of AISI 316 stainless steel processed by “selective laser melting”, following different manufacturing strategies10.1007/s00170-010-2631-5 ↗
13. Mechanical and Microstructural Anisotropy of Laser Powder Bed Fusion 316L Stainless Steel10.3390/ma15020551 ↗
14. Microstructure evolution of the stainless steel 316L subjected to different routes of equal channel angular pressing
15. A comparative study on the structure and quality of SLM and cast AISI 316L samples subjected to WEDM processing10.3390/ma15030701 ↗
16. Investigations on mechanical properties of lattice structures with different values of relative density made from 316L by selective laser melting (SLM)10.3390/ma13092204 ↗
17. Investigation of crystal growth mechanism during selective laser melting and mechanical property characterization of 316L stainless steel parts10.1016/j.matdes.2016.03.111 ↗
18. Corrosion and microstructural investigation on additively manufactured 316L stainless steel: experimental and statistical approach10.3390/ma15041605 ↗
19. Microstructure and mechanical properties of 316L austenitic stainless steel processed by different SLM devices10.1007/s00170-020-05371-1 ↗
20. Analysis of selective laser melting process parameters effect on mechanical and material properties for stainless steel 316L
21. The effect of hatch angles on the microstructure and mechanical properties of selective laser melting 316L stainless steel
22. Effect of manufacturing parameters on mechanical properties of 316L stainless steel parts fabricated by selective laser melting: a computational framework10.1016/j.matdes.2016.09.043 ↗
23. Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting10.1007/s00170-014-6297-2 ↗
24. Additive manufacturing–a review of hot deformation behavior and constitutive modeling of flow stress10.1016/j.cossms.2022.100992 ↗
25. Machine-learning assisted laser powder bed fusion process optimization for AlSi10Mg: new microstructure description indices and fracture mechanisms10.1016/j.actamat.2020.10.010 ↗
26. Investigation of creep behavior of 316L stainless steel produced by selective laser melting with various processing parameters10.1007/s12206-020-0717-z ↗
27. On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting10.1016/j.engfracmech.2014.03.008 ↗
28. An investigation of the microstructure and fatigue behavior of additively manufactured AISI 316L stainless steel with regard to the influence of heat treatment10.3390/met8040220 ↗
29. 316L stainless steel designed to withstand intermediate temperature10.1016/j.matdes.2017.08.072 ↗
30. Temperature‐dependent dynamic strain aging in selective laser melted 316L10.1002/adem.202001501 ↗
31. The microstructure, mechanical properties and corrosion resistance of 316 L stainless steel fabricated using laser engineered net shaping10.1016/j.msea.2016.09.028 ↗
32. Effect of grain size on the corrosion behavior of fully recrystallized ultra-fine grained 316L stainless steel fabricated by high-energy ball milling and hot isostatic pressing sintering10.1016/j.matchar.2021.110995 ↗
33. On the corrosion and metastable pitting characteristics of 316L stainless steel produced by selective laser melting10.1149/2.0551706jes ↗
34. Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes10.1016/j.jmst.2019.03.003 ↗
35. A microstructural study on the observed differences in charpy impact behavior between hot isostatically pressed and forged 304L and 316L austenitic stainless steel10.1007/s11661-015-3140-9 ↗
36. Mechanical properties and constitutive model of selective laser melting 316L stainless steel at different scanning speeds
37. Constructing the high temperature efficiency and instability maps of selective laser melted 316L stainless steel through artificial neural network modeling10.1016/j.jmrt.2022.04.116 ↗
38. Effect of heat treatment on microstructure and mechanical properties of 316L steel synthesized by selective laser melting10.1016/j.msea.2019.01.110 ↗
39. Structural and micromechanical properties of 316L stainless steel produced by selective laser melting
40. Effect of heat treatment of 316L stainless steel produced by selective laser melting (SLM), Solid Freeform Fabrication 2016
41. Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes10.1016/j.jmst.2019.03.003 ↗
42. Enhancement of an additive-manufactured austenitic stainless steel by post-manufacture heat-treatment10.1016/j.msea.2019.04.111 ↗
43. Heat treatment effect on the microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting for proton exchange membrane fuel cells10.1016/j.electacta.2018.04.188 ↗
44. Effect of post-heat treatment cooling on microstructure and mechanical properties of selective laser melting manufactured austenitic 316L stainless steel10.1108/RPJ-12-2019-0320 ↗
45. Work hardening behavior and substructure evolution of a low-density steel during compressive deformation10.1016/j.jmrt.2022.11.032 ↗
46. On the substructure development and continuous recrystallization in the course of selective laser melting of 316L stainless steel
47. On the capability of grain refinement during selective laser melting of AlSi10Mg alloy10.1016/j.jmrt.2023.05.122 ↗
48. About metastable cellular structure in additively manufactured austenitic stainless steels
49. Microstructures and mechanical properties of H13 tool steel fabricated by selective laser melting10.3390/ma15072686 ↗
50. Effect of manufacturing parameters on mechanical properties of 316L stainless steel parts fabricated by selective laser melting: a computational framework10.1016/j.matdes.2016.09.043 ↗
51. Simultaneously enhanced strength and ductility for 3D-printed stainless steel 316L by selective laser melting10.1038/s41427-018-0018-5 ↗
52. Hot compression behavior and microstructure of selectively laser-melted IN718 alloy
53. An investigation into microstructure and high-temperature mechanical properties of selective laser-melted 316L stainless steel toward the development of hybrid Ampliforge process10.1007/s00170-020-05870-1 ↗
54. Comparatively evaluating the room and high temperature mechanical properties of AlSi10Mg alloy produced by selective laser melting10.1016/j.jmrt.2022.10.162 ↗
55. The high temperature flow behavior of additively manufactured Inconel 625 superalloy10.1088/2053-1591/ab44f6 ↗
56. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
57. Effect of heat treatment on mechanical properties and microstructure of selective laser melting 316L stainless steel
58. Dynamic recrystallization under hot deformation of additively manufactured 316 L stainless steel10.1016/j.matchar.2023.113055 ↗
59. Modelling discontinuous dynamic recrystallization using a physically based model for nucleation10.1016/j.actamat.2009.07.024 ↗
60. Mechanisms of DRX nucleation with grain boundary bulging and subgrain rotation during the hot working of nickel-based superalloys with columnar grains10.1016/j.jallcom.2019.01.334 ↗
61. Corrosion and microstructural investigation on additively manufactured 316L stainless steel: experimental and statistical approach10.3390/ma15041605 ↗
62. New insights on cellular structures strengthening mechanisms and thermal stability of an austenitic stainless steel fabricated by laser powder-bed-fusion10.1016/j.actamat.2020.11.018 ↗
63. Recrystallization-based grain boundary engineering of 316L stainless steel produced via selective laser melting10.1016/j.actamat.2020.09.015 ↗
64. A model of continuous dynamic recrystallization10.1016/S1359-6454(03)00078-8 ↗
65. Evaluation of corrosion behavior of 316 L stainless steel manufactured by SLM method after heat treatment and surface treatments
66. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗