Pozzolanic performance and characteristic analysis of binary blended cement incorporating ceramic polishing sludge
Source abstract
Abstract
The waste generated during ceramic polishing is typically disposed of in landfills rather than being recycled within the production facility, potentially causing environmental harm. This study aims to enhance industrial waste utilization and reduce CO2 emissions in the cement industry by investigating the feasibility of incorporating ceramic sludge from polishing processes into an innovative binary blended cement. Different binders were prepared with varying amounts of ceramic polishing sludge (CPS), ranging from 10% to 50%, and tested against the ASTM C595 standards. The results were compared with those of ordinary Portland cement (OPC). This approach involves evaluating the pozzolanic activity and conducting an advanced characterization assessment of CPS and binary blended ceramic polishing sludge cement (CPSC) paste. This study employed a combination of physical, mechanical, and chemical tests, including setting time, particle size distribution (PSD), Brunauer-Emmett-Teller (BET) specific surface area, compressive strength, X-ray diffraction (XRD), scanning electron microscopy (SEM), heat of hydration, and differential scanning calorimetry/thermogravimetric analysis (DSC/TGA). The results indicated that CPS can be used as a pozzolanic material to create innovative binders with properties comparable to those of OPC. The Strength Activity Index (SAI) values affirmed the pozzolanic properties of CPS, exceeding 75% for up to 40% CPS replacement. Incorporating CPS in the blended cement resulted in a slower rate of cement hydration, leading to prolonged setting times and reduced early strength development. Although the compressive strength decreased with increasing CPS content, it remained within the acceptable ASTM C595 limits with up to 50% replacement. Nevertheless, the optimal replacement level of OPC with CPS was determined to be 50%. Furthermore, CPS substitution reduced the dry density and improved the water absorption and apparent porosity, reflecting microstructural changes. The SEM images revealed that the blended CPSC had a lower apparent porosity than the pure OPC. The DSC/TGA analysis demonstrated that the blended cement had a lower calcium hydroxide content and higher silica than pure OPC.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Recycling and utilization of industrial and municipal waste in materials production · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (78)
Show source-provided references
1. Pathways towards sustainable concrete10.1016/j.cemconres.2022.106718 ↗
2. The past and future of sustainable concrete: a critical review and new strategies on cement-based materials10.1016/j.jclepro.2020.123558 ↗
3. A huge number of artificial waste material can be supplementary cementitious material (SCM) for concrete production – a review part II10.1016/j.jclepro.2015.12.115 ↗
4. Hydration mechanism and environmental impacts of blended cements containing co-combustion ash of sewage sludge and rice husk: compared with blended cements containing sewage sludge ash10.1016/j.scitotenv.2022.161116 ↗
5. J.M. Khatib, O. Baalbaki, A.A. ElKordi, 15 - metakaolin, in: R. Siddique, P. Cachim (Eds.), Waste and supplementary cementitious materials in concrete, Woodhead Publishing2018, pp. 493-511..10.1016/B978-0-08-102156-9.00015-8 ↗
6. M.J. McCarthy, T.D. Dyer, 9 - Pozzolanas and pozzolanic materials, in: P.C. Hewlett, M. Liska (Eds.), Lea's chemistry of cement and concrete (fifth ed.), Butterworth-Heinemann2019, pp. 363-467..10.1016/B978-0-08-100773-0.00009-5 ↗
7. Malhotra · 1996
8. Influence of pozzolan from various by-product materials on mechanical properties of high-strength concrete10.1016/j.conbuildmat.2005.09.011 ↗
9. Durability of mortar and concrete made up of pozzolans as a partial replacement of cement: a review10.1016/j.conbuildmat.2016.04.147 ↗
10. Importance of using the natural pozzolans on concrete durability10.1016/S0008-8846(01)00714-1 ↗
11. Value-added recycling of cathode ray tube funnel glass into high-performance radiation shielding concrete10.1016/j.resconrec.2023.107252 ↗
12. Characterization of ceramic waste aggregate concrete10.1016/j.hbrcj.2016.11.003 ↗
13. Reusing ceramic wastes in concrete10.1016/j.conbuildmat.2009.10.023 ↗
14. Microstructure and properties of recycled concretes using ceramic sanitary ware industry waste as coarse aggregate10.1016/j.conbuildmat.2011.12.075 ↗
15. Utilization of ceramic waste as partially cement substitute – a review10.1016/j.conbuildmat.2021.124009 ↗
16. New blended cement from polishing and glazing ceramic sludge10.1111/j.1744-7402.2009.02368.x ↗
17. Recycling of industrial wastes in ceramic manufacturing: state of art and glass case studies10.1016/j.ceramint.2016.05.205 ↗
18. Effectiveness of ceramic tile polishing residues as supplementary cementitious materials for cement mortars10.1016/j.susmat.2015.05.001 ↗
19. High performance concrete incorporating ceramic waste powder as large partial replacement of Portland cement10.1016/j.conbuildmat.2017.03.115 ↗
20. Valorization of ceramic sludge waste as alternative flux: a way to clean production in the sanitary ware industry10.1016/j.clet.2022.100453 ↗
21. Recycling of polishing porcelain stoneware residues in ceramic tiles10.1016/j.jeurceramsoc.2007.01.021 ↗
22. Assessing the environmental impact of ceramic tile production in Thailand10.2109/jcersj2.118.887 ↗
23. Use of screen glass and polishing sludge in waste-based expanded aggregates for resource-saving lightweight concrete10.1016/j.jclepro.2021.130089 ↗
24. Properties of fresh and hardened concrete containing supplementary cementitious materials
25. Waste ceramic powder as a pozzolanic supplementary filler of cement for developing sustainable building materials10.1016/j.jclepro.2020.120853 ↗
26. Pozzolanic activity of tiles, bricks and ceramic sanitary-ware in eco-friendly Portland blended cements10.1016/j.jclepro.2020.123713 ↗
27. Ismail · 2015 · 1087
28. Strength development and physical properties of cement paste with incorporated ceramic powder
29. Surface properties of ceramic waste powder and its effect on the rheology, hydration and strength development of cement paste
30. Reutilizing ceramic polishing waste as powder filler in mortar to reduce cement content by 33% and increase strength by 8510.1016/j.powtec.2019.07.043 ↗
31. Utilization of ceramic tile demolition waste as supplementary cementitious material: an early-age investigation
32. Mohit · Ceramic waste powder as alternative mortar-based cementitious material · 2019 · 116 · 107
33. DSC and TG analysis of a blended binder based on waste ceramic powder and Portland cement10.1007/s10765-016-2043-3 ↗
34. Ceramic waste as an efficient material for enhancing the fire resistance and mechanical properties of hardened Portland cement pastes10.1016/j.conbuildmat.2017.08.040 ↗
35. Positive impact of ultra fine-ceramic waste on the physico-mechanical features and microstructure of white cement pastes composites10.1016/j.jmrt.2020.05.087 ↗
36. Rheological and calorimetric behaviour of cements blended with containing ceramic sanitary ware and construction/demolition waste10.1016/j.conbuildmat.2012.11.112 ↗
37. Recycling of porcelain tile polishing residue in Portland cement: hydration efficiency10.1021/es203118w ↗
38. Wang · 2009 · 101
39. Strength and durability of concrete containing ceramic waste powder and Blast Furnace slag10.1061/(ASCE)MT.1943-5533.0004031 ↗
40. Test research on effects of ceramic polishing powder on carbonation and sulphate-corrosion resistance of concrete10.1016/j.conbuildmat.2014.01.023 ↗
41. Ceramic waste powder an alternative cement replacement – characterization and evaluation10.1016/j.susmat.2018.e00063 ↗
42. The Use of ceramic waste powder (CWP) in making eco-friendly concretes
43. Influence of binary blended cement containing slag and limestone powder to produce sustainable mortar10.1063/5.0171499 ↗
44. Study of fresh properties of cemented paste backfill material with ternary cement blends10.1016/j.conbuildmat.2023.134287 ↗
45. Correlation between slag reactivity and cement paste properties: the influence of slag chemistry10.1061/JMCEE7.MTENG-16385 ↗
46. Assessing the potential of sludge generated by the pulp and paper industry in assembling locking blocks10.1016/j.jobe.2019.02.012 ↗
47. Azevedo · 2021
48. 2022 · 5
49. 2022 · 11
50. 2021 · 10
51. 2022 · 9
52. Supplementary cementitious materials10.1016/j.cemconres.2010.12.001 ↗
53. Effects of sample preparation and Interpretation of thermogravimetric curves on calcium hydroxide in hydrated pastes and mortars10.3141/2290-02 ↗
54. Scrivener · 2016
55. Evidences of chemical interaction between EVA and hydrating Portland cement10.1016/S0008-8846(02)00805-0 ↗
56. 2020 · 11
57. 2021 · 8
58. 2021 · 3
59. Effect of particle size distribution of fly ash–cement system on the fluidity of cement pastes10.1016/S0008-8846(02)01054-2 ↗
60. The effect of particle size distribution on the properties of blended cements incorporating GGBFS and natural pozzolan (NP)10.1016/j.powtec.2007.03.033 ↗
61. Influence of cement particle-size distribution on early age autogenous strains and stresses in cement-based materials10.1111/j.1151-2916.2001.tb00619.x ↗
62. Comprehensive assessment of ceramic ETP sludge waste as a SCM for the production of concrete
63. Robustness of self-compacting concrete incorporating bone China ceramic waste powder along with granite cutting waste for sustainable development10.1016/j.jclepro.2022.132969 ↗
64. Hydration of ternary blended cements with sewage sludge ash and limestone: hydration mechanism and phase assemblage10.1016/j.conbuildmat.2023.130868 ↗
65. Pozzolanic effect of porcelain polishing residue in Portland cement10.1016/j.jclepro.2015.03.096 ↗
66. Hydration heat development in blended cements containing fine-ground ceramics10.1016/j.tca.2012.05.022 ↗
67. Kunal, Strength, permeability and microstructure of self-compacting concrete containing rice husk ash10.1016/j.biosystemseng.2014.12.005 ↗
68. Differential scanning calorimetry study of ordinary Portland cement10.1016/S0008-8846(99)00128-3 ↗
69. The influence of thermal-stressing (up to 1000°C) on the physical, mechanical, and chemical properties of siliceous-aggregate, high-strength concrete10.1016/j.conbuildmat.2013.01.020 ↗
70. Differential scanning calorimetry study of ordinary Portland cement paste containing metakaolin and theoretical approach of metakaolin activity10.1016/S0958-9465(00)00090-1 ↗
71. On the hydration of water-entrained cement–silica systems: combined SEM, XRD and thermal analysis in cement pastes10.1016/j.tca.2011.02.003 ↗
72. Effect of ceramic polishing waste on the properties of alkali-activated slag pastes: shrinkage, hydration and mechanical property
73. Setting and mechanical properties of alkali-activated fly ash/slag concrete manufactured at room temperature10.1016/j.conbuildmat.2013.05.107 ↗
74. The use of ceramic sludge and recycled glass to obtain engobes for manufacturing ceramic tiles10.1016/j.jclepro.2014.08.091 ↗
75. Synthesis, characterization and modeling of new building insulation material using ceramic polishing waste residue10.1016/j.conbuildmat.2015.03.089 ↗
76. Characterization of ceramic roof tile wastes as pozzolanic admixture10.1016/j.wasman.2008.10.019 ↗
77. Use of ceramic industry milling and glazing waste as an active addition in cement10.1111/jace.15355 ↗
78. Test research on the effect of waste ceramic polishing powder on the compressive strength and chloride penetration resistance of seawater concrete10.1016/j.conbuildmat.2023.131590 ↗