journal article·2024-05Open access

The role of Si in enhancing the stability of residual austenite and mechanical properties of a medium carbon bainitic steel

Shaolong Zhang, Wen Zhou, Feng Hu, Serhii Yershov, Kaiming Wu

Abstract

In this work, two bainitic steels with medium carbon content were developed by adding different Si. The mechanical properties of the two test steels and the stability of their retained austenite were studied, and the influence of Si in the steels was discussed. The results show that the film-like retained austenite of the high Si bainitic steel is greatly increased compared with that of the low Si bainitic steel and that the C content is increased, effectively preventing crack propagation and significantly improving the comprehensive mechanical properties. Due to the different Si content in the test steels, the orientation relationship of austenite in the steels has changed, and when the Si content is increased from 0.7 wt% to 1.4 wt%, the variant selection of bainite becomes weaker. Moreover, the increase of Si content not only inhibits the precipitation of carbides but also promotes the accumulation of C in the austenite, which improves the stability of the retained austenite.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Magnetic Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Insight into the impact of microstructure on crack initiation/propagation behavior in carbide-free bainitic steel during tensile deformation10.1016/j.msea.2022.143175 ↗
2. Quantitative evaluation of the contribution of carbide-free bainite, lath martensite, and retained austenite on the mechanical properties of C-Mn-Si high-strength steels10.1016/j.matchar.2023.112802 ↗
3. The combining effects of ausforming and below-Ms or above-Ms austempering on the transformation kinetics, microstructure and mechanical properties of low-carbon bainitic steel10.1016/j.matdes.2019.108123 ↗
4. Unravelling the mechanical behaviour of advanced multiphase steels isothermally obtained below Ms10.1016/j.matdes.2020.108484 ↗
5. Austenite stability of ultrafine-grained transformation-induced plasticity steel with Mn partitioning10.1016/j.scriptamat.2011.04.010 ↗
6. Continuous cooling transformation diagrams and properties of micro-alloyed TRIP steels10.1016/j.msea.2006.01.128 ↗
7. A novel two-step intercritical annealing process to improve mechanical properties of medium Mn steel10.1016/j.actamat.2019.07.014 ↗
8. Bimodal size-distribution of bainite plates10.1016/j.msea.2005.12.070 ↗
9. Effects of aluminum on the microstructure and phase transformation of TRIP steels10.1007/s12540-012-4012-0 ↗
10. Microstructure–hardness relationship in quenched and partitioned medium-carbon and high-carbon steels containing silicon10.1016/j.msea.2008.08.028 ↗
11. Effects of partitioning parameters in quenching and partitioning on microstructure and mechanical properties of an ultra-high strength low-alloy steel10.1002/mawe.201700267 ↗
12. The influence of silicon additions on the deformation behavior of austenite-ferrite duplex medium manganese steels10.1016/j.actamat.2018.02.005 ↗
13. Recent progress in medium-Mn steels made with new designing strategies, a review10.1016/j.jmst.2017.06.017 ↗
14. Composition design of nanocrystalline bainitic steels by diffusionless solid reaction10.1007/s12540-014-3002-9 ↗
15. Bhadeshia · 1992
16. Development of hard bainite10.2355/isijinternational.43.1238 ↗
17. Strengthening and mechanical stability mechanisms in nanostructured bainite10.1007/s10853-013-7408-4 ↗
18. Investigation of microstructural evolution and crack extension in a quenching and partitioning (Q & P) steel at different strain rates10.1016/j.jmrt.2023.03.149 ↗
19. Quantitative phase analysis of martensite-bainite steel using EBSD and its microstructure, tensile and high-cycle fatigue behaviors10.1016/j.msea.2020.139375 ↗
20. The influence of the lath morphology on the yield stress and transition temperature of martensitic- bainitic steels10.1007/BF02658305 ↗
21. Correlation of ferrite and martensite micromechanical behavior with mechanical properties of ultrafine grained dual phase steels10.1016/j.msea.2019.138206 ↗
22. Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling10.1016/j.msea.2022.143904 ↗
23. Effect of Mn on tempering stability of retained austenite in bainite steel
24. Microstructure-property relationship in the quenching and partitioning (Q&P) steel10.1016/j.matchar.2022.112561 ↗
25. Microstructure and mechanical properties of a medium-carbon bainitic steel by a novel quenching and dynamic partitioning (Q-DP) process10.1016/j.msea.2016.03.042 ↗
26. Fatigue property and microstructure deformation behavior of multiphase microstructure in a medium-carbon bainite steel under rolling contact condition10.1016/j.ijfatigue.2019.04.019 ↗
27. Microstructure, tensile and toughness properties after quenching and partitioning treatments of a medium-carbon steel10.1016/j.msea.2012.08.130 ↗
28. Effect of rapid tempering at high temperature on microstructure, mechanical properties and stability of retained austenite of medium carbon ultrafine bainitic steel10.1016/j.jmrt.2023.12.238 ↗
29. Effect of retained austenite on impact toughness and fracture behavior of medium carbon submicron-structured bainitic steel10.1016/j.jmrt.2021.07.011 ↗
30. Theoretical design and advanced microstructure in super high strength steels10.1016/j.matdes.2008.08.042 ↗
31. Effect of processing techniques on microstructure and mechanical properties of carbide-free bainitic rail steels
32. Low cycle fatigue behavior in a medium-carbon carbide-free bainitic steel10.1016/j.msea.2016.03.077 ↗
33. A heterostructured bainitic steel produced by two-step austempering and low-temperature ausforming10.1016/j.scriptamat.2023.115943 ↗
34. Study on microstructures and properties of carbide-free and carbide-bearing bainitic steels10.1016/j.msea.2017.12.108 ↗
35. Determining role of microstructure on crack arrest and propagation phenomenon in low-carbon microalloyed steel10.1016/j.msea.2019.06.019 ↗
36. Effect of austempering treatment on the microstructure and mechanical properties of 0.4C–1.5Si-1.5Mn TRIP-aided bainitic ferrite steel10.1016/j.msea.2021.141479 ↗
37. Influence of carbon concentration and reaction temperature upon bainite morphology in Fe-C-2 Pct Mn alloys10.1007/BF02672559 ↗
38. Effect of Si content on microstructure and properties of high carbon bainitic steel
39. The influence of the Si and Mn concentrations on the kinetics of the bainite transformation in Fe-C-Si-Mn alloys10.1007/BF02672566 ↗
40. Crystallographic analysis of isothermally transformed bainite in 0.2C–2.0Mn–1.5Si–0.6Cr steel using EBSD10.1016/j.jmst.2013.01.015 ↗
41. Variant selection in grain boundary nucleation of bainite in Fe-2Mn-C alloys10.1016/j.actamat.2017.01.035 ↗
42. Influence of austempering temperature on microstructure and mechanical properties of high-carbon nanostructured bainitic steels10.1016/j.msea.2022.143334 ↗
43. On the crystallographic characteristics of nanobainitic steel10.1016/j.actamat.2017.01.058 ↗
44. Estimation of bainite plate-thickness in low-alloy steels10.1016/S0921-5093(97)00701-6 ↗
45. Austenite carbon enrichment and decomposition during quenching and tempering of high silicon high carbon bearing steel10.1016/j.actamat.2023.118742 ↗
46. The distribution of substitutional alloying elements during the bainite transformation10.1007/BF02656567 ↗
47. Redistribution of alloying elements during tempering of a nanocrystalline steel10.1016/j.actamat.2007.09.018 ↗
48. The role of silicon in carbon partitioning processes in martensite/austenite microstructures10.1016/j.matdes.2017.04.080 ↗