Dynamic precipitation and its effect on microstructure of 2195 Al–Li alloy during medium/high temperature deformation
Source abstract
Abstract
In this work, the homogenized Al-Li alloys were compressed at different strains (20%-80%) under medium (370 °C) and high temperatures (470 °C), and their microstructures were characterized by SEM, EBSD, and TEM. The evolution of dynamic precipitation (DPN) during thermal deformation and its effect on microstructure and flow behavior were investigated. The results show that obvious flow softening appears with the increase of strain at medium temperature deformation while not at high temperatures, associated with the reduction of solid solution strengthening caused by DPN and the fragmentation of T1 precipitates with large aspect ratios. The T1 precipitates undergo fragmentation, dissolution and re-precipitation to develop two types of T1 bands. Deformation at medium temperatures, DPN inhibits dislocations and (sub)grain boundary movement, and mainly dynamic recovery (DRV) accompanied by little dynamic recrystallization (DRX) occurs. The fine secondary phases at high temperatures are dominated by the pre-existing Al3Zr phase, and some precipitates are observed until 80% strain, however, DPN has little influence on precipitation hardening and DRX and occurs later than DRX. DRX mechanism changes from CDRX (20-60%) to CDRX and GDRX (80%) with strain at high temperatures. Furthermore, the deformed grains tend to develop in <101>//CD (compression direction) fiber texture during deformation, and the texture strength increases with increasing strain and decreasing temperature.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (71)
Show source-provided references
1. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
2. Superior mechanical properties and microstructural evolution of 2195-T6 Al-Li alloys at a high strain rate10.1016/j.msea.2021.141314 ↗
3. Microstructure, texture and hardness of Al–Cu–Li alloy sheet during hot gas forming with integrated heat treatment10.1016/j.matdes.2016.01.001 ↗
4. Plastic flow behavior and microstructure characteristics of light-weight 2060 Al-Li alloy10.1016/j.msea.2018.09.010 ↗
5. A review on superplastic formation behavior of Al alloys
6. A novel heterogeneous multi-wire indirect arc directed energy deposition for in-situ synthesis Al-Zn-Mg-Cu alloy: process, microstructure and mechanical properties
7. Microstructure evolution and physical-based diffusion constitutive analysis of Al-Mg-Si alloy during hot deformation10.1016/j.matdes.2019.108181 ↗
8. Modelling continuous dynamic recrystallization of aluminum alloys based on the polycrystal plasticity approach10.1016/j.ijplas.2020.102710 ↗
9. EBSD study of a hot deformed nickel-based superalloy10.1016/j.jallcom.2015.04.008 ↗
10. A critical assessment of experimental investigation of dynamic recrystallization of metallic materials10.1016/j.matdes.2020.108873 ↗
11. Dynamic recrystallization mechanisms of 2195 aluminum alloy during medium/high temperature compression deformation10.1016/j.msea.2020.140650 ↗
12. Flow curve correction and processing map of 2050 Al–Li alloy10.1016/S1003-6326(18)64674-6 ↗
13. Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions10.1016/j.jmapro.2020.09.063 ↗
14. A new dynamic recrystallisation model of an extruded Al-Cu-Li alloy during high-temperature deformation10.1016/j.msea.2014.11.095 ↗
15. Microstructure evolution and precipitation characteristics of spray-formed and subsequently extruded 2195 Al-Li alloy plate during solution and aging process10.1016/j.jmatprotec.2020.116718 ↗
16. Microstructure and mechanical properties of 2195 alloys prepared by traditional casting and spray forming10.1016/j.msea.2020.139337 ↗
17. Heterogeneous Zr solute segregation and Al3Zr dispersoid distributions in Al–Cu–Li alloys10.1016/j.actamat.2015.03.057 ↗
18. Microstructure and hot deformation behavior of a new aluminum–lithium–copper based AA2070 alloy10.1016/j.msea.2020.139048 ↗
19. The double-edge effect of second-phase particles on the recrystallization behaviour and associated mechanical properties of metallic materials10.1016/j.pmatsci.2017.10.004 ↗
20. Texture analysis of the transition from slip to grain boundary sliding in a discontinuously recrystallized superplastic aluminum alloy10.1016/S1359-6454(01)00128-8 ↗
21. Mechanical behaviour and microstructural evolution in superplastic Al–Li–Mg–Cu–Zr AA809010.1016/j.actamat.2007.05.017 ↗
22. Hot deformation behavior and microstructure evolution of the spray deposited and secondary hot extruded 2195 Al–Li alloy10.1016/j.jmrt.2022.08.055 ↗
23. Precipitation behavior and its effect on the dynamic recrystallization of a novel extruded Al-Cu-Li alloy10.1016/j.matdes.2022.111135 ↗
24. T1 precipitate bands and particle stimulated nucleation in 2195 Al-Cu-Li alloy during hot deformation10.1016/j.jallcom.2022.164716 ↗
25. Effects of re-solution, pre-stretching and double re-ageing treatment on mechanical behavior and microstructure of 2195 Al–Cu–Li alloy10.1016/j.msea.2022.144172 ↗
26. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
27. Dynamic precipitation and dynamic recrystallization during hot deformation of a solutionized WE43 magnesium alloy10.1016/j.msea.2019.138076 ↗
28. Microstructure evolution of spray deposited and as-cast 2195 Al-Li alloys during homogenization10.1016/j.jmst.2020.12.028 ↗
29. Influence of homogenization treatment on microstructure and recrystallization behavior of 2195 Al-Li alloy10.1016/S1003-6326(23)66257-0 ↗
30. Deformation behavior and dynamic recrystallization during hot compression in homogenized Al–6Mg–0.8 Mn alloys10.1016/j.msea.2022.142953 ↗
31. Deformation-induced dynamic precipitation of 14H-LPSO structure and its effect on dynamic recrystallization in hot-extruded Mg-Y-Zn alloys10.1016/j.ijplas.2023.103573 ↗
32. Effects of heat treatment on the microstructure and mechanical properties of extruded 2196 Al-Cu-Li alloy10.1016/j.matdes.2020.108746 ↗
33. The influence of precipitation on plastic deformation of Al-Cu-Li alloys10.1016/j.actamat.2013.03.015 ↗
34. Effects of texture and precipitates characteristics on anisotropic hardness evolution during artificial aging for an Al–Cu–Li alloy10.1016/j.matdes.2021.110216 ↗
35. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
36. Study on the dynamic recrystallization mechanisms of Inconel 740 superalloy during hot deformation10.1016/j.jallcom.2019.153325 ↗
37. Work hardening characteristics and microstructural evolution during hot deformation of a nickel superalloy at moderate strain rates10.1016/j.jallcom.2017.03.158 ↗
38. Hetero-deformation induced (HDI) hardening does not increase linearly with strain gradient10.1016/j.scriptamat.2019.08.022 ↗
39. Physically based constitutive analysis and microstructural evolution of AA7050 aluminum alloy during hot compression10.1016/j.matdes.2016.06.023 ↗
40. Discontinuous dynamic recrystallization and nucleation mechanisms associated with 2-, 3- and 4-grain junctions of polycrystalline nickel-based superalloys10.1016/j.matdes.2023.112041 ↗
41. Analysis and characterization of dynamic recrystallization and grain structure evolution in friction stir welding of aluminum plates10.1016/j.actamat.2021.116692 ↗
42. Strain rate dependent microstructural evolution during hot deformation of a hot isostatically processed nickel base superalloy10.1016/j.jallcom.2016.04.185 ↗
43. Dynamic precipitation and recrystallization mechanism during hot compression of Mg-Gd-Y-Zr alloy10.1016/j.jmrt.2021.08.013 ↗
44. Hot deformation and dynamic recrystallization in Al-Mg-Si alloy10.1016/j.matchar.2021.110976 ↗
45. Dynamic recrystallization and precipitation behavior of a novel Sc, Zr alloyed Al-Zn-Mg-Cu alloy during hot deformation10.1016/j.matchar.2021.111629 ↗
46. Microstructural evolution and dynamic recrystallization behavior of the homogenized 2195 Al–Li alloy during hot deformation10.1007/s12540-023-01397-8 ↗
47. Deformation behavior and microstructure evolution of Al–5.06Mg–1.67Li–0.51Zn alloy under hot compression10.1016/j.jmrt.2021.10.084 ↗
48. Hot deformation constitutive model and processing maps of homogenized Al–5Mg–3Zn–1Cu alloy10.1016/j.jmrt.2021.06.069 ↗
49. Hot deformation behavior and microstructure evolution of annealed Al-7.9Zn-2.7Mg-2.0Cu (wt%) alloy10.1016/j.jallcom.2018.05.307 ↗
50. Crash-worthiness of a recently-developed AA 2624 aluminum alloy: experimental studies10.1016/j.msea.2019.138389 ↗
51. Orientation dependence of the dislocation microstructure in compressed body-centered cubic molybdenum10.1016/j.matchar.2014.02.001 ↗
52. Texture of metals, texture
53. Microstructure and texture evolution of AZ31 Mg alloy after uniaxial compression and annealing10.1016/j.jma.2018.11.003 ↗
54. Precipitation strengthening at ambient and elevated temperatures of heat-treatable Al(Sc) alloys10.1016/S1359-6454(02)00496-2 ↗
55. Modelling dynamic precipitation in pre-aged aluminium alloys under warm forming conditions10.1016/j.actamat.2022.118036 ↗
56. Excess vacancies and the nucleation of precipitates in aluminum-silicon alloys10.1016/0001-6160(70)90055-6 ↗
57. Dynamic precipitation and recrystallization in Mg-9wt.%Al during equal-channel angular extrusion: a comparative study to conventional aging10.1016/j.actamat.2019.04.046 ↗
58. Effects of dynamic recrystallization and strain-induced dynamic precipitation on the corrosion behavior of partially recrystallized Mg-9Al-lZn alloys10.1016/j.jma.2020.09.005 ↗
59. Dislocation pipe diffusion10.1016/0001-6160(64)90220-2 ↗
60. Quantitative measurements of dynamic precipitation during fatigue of an Al–Zn–Mg–(Cu) alloy using small-angle X-ray scattering10.1016/j.actamat.2014.04.027 ↗
61. Increasing strength and ductility of a Mg–9Al alloy by dynamic precipitation assisted grain refinement during multi-directional forging10.1016/j.msea.2020.139192 ↗
62. Hot deformation behavior and processing maps of an as-cast Al-5Mg-3Zn-1Cu (wt%) Alloy10.3390/ma16114093 ↗
63. Influence of equal-channel angular pressing on precipitation in an Al–Zn–Mg–Cu alloy - ScienceDirect10.1016/j.actamat.2009.03.017 ↗
64. Dynamic microstructural evolution of Al-Cu-Li alloys during hot deformation10.1016/j.matchar.2022.112135 ↗
65. A comprehensive review of magnesium-based alloys and composites processed by cyclic extrusion compression and the related techniques10.1016/j.pmatsci.2022.101016 ↗
66. Effects of T1/T2 precipitates on deformation behavior and microstructure evolution of AA2099 Al-Li alloy: experimental investigation and crystal plasticity finite element modeling10.1016/j.jmrt.2022.01.009 ↗
67. Strengthening of an Al–Cu–Sn alloy by deformation-resistant precipitate plates10.1016/j.actamat.2008.03.028 ↗
68. Quantification and modelling of the microstructure/strength relationship by tailoring the morphological parameters of the T-1 phase in an Al-Cu-Li alloy10.1016/j.actamat.2014.04.046 ↗
69. Strengthening mechanisms of T1 precipitates and their influence on the plasticity of an Al–Cu–Li alloy10.1016/j.msea.2014.03.024 ↗
70. Effect of concurrent precipitation on recrystallization and evolution of the p-texture component in a commercial Al-Mn Alloy10.1007/s11661-010-0265-8 ↗
71. Dynamic precipitation behavior and mechanical properties of hot-extruded Mg89Y4Zn2Li5 alloys with different extrusion ratio and speed10.1016/j.msea.2020.140121 ↗