Identification of tool wear and surface morphology measurements in sustainable milling of Al 6082 hybrid metal matrix composite
Source abstract
Abstract
Aluminium hybrid metal matrix composites have significantly increased in many advanced applications owing to their unique properties. However, these hybrid composites are difficult to machine because of hard reinforcements in the matrix. After identifying the optimum cutting conditions, it's crucial to identify the tool wear mechanisms to keep surface roughness within the desired range, especially with hybrid composites. Hence, the present work mainly focuses on identifying the wear mechanism of PVD-coated TiAlN cutting tool inserts during the end milling of Al 6082 hybrid metal matrix composites. MQL, CO2, and a combination of MQL + CO2 cooling conditions were employed over the cutting zone to decrease tool wear. In the context of 300 mm of cutting length, employing CO2, MQL, and MQL + CO2 conditions led to a significant reduction in tool wear by 34.5 %, 50.1 %, and 74.7 %, respectively, compared to dry cutting. The results showed that the MQL + CO2 condition produced better results than the other cooling conditions, improving tool life and surface quality.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing10.1016/j.matchar.2017.01.016 ↗
2. Experimental investigation and optimization of process parameters in milling of hybrid metal matrix composites10.1080/10426914.2012.677911 ↗
3. Study on mechanical behaviours of newly formulated aluminium alloy (6082) reinforced with boron carbide and rice husk ash
4. Investigation on mechanical characterization of Al/Mos2/WC hybrid composite10.1016/j.matpr.2022.08.014 ↗
5. Synthesis of B4C and BN reinforced Al7075 hybrid composites using stir casting method10.1016/j.jmrt.2020.03.043 ↗
6. Manufacturing of aluminum composite material using stir casting process
7. Experimental investigation on stir casting of a metal matrix composite material10.1177/25165984211015761 ↗
8. Wear mechanisms and performance of abrasively ground polycrystalline diamond tools of different diamond grains in machining titanium alloy10.1016/j.jmapro.2017.08.010 ↗
9. Recent research development of CNC based milling machining conditions: a comprehensive review10.1016/j.matpr.2022.04.582 ↗
10. Performance of cryogenically treated carbide inserts under sustainable cryo-lubrication assisted milling of Inconel X750 alloy10.1016/j.susmat.2021.e00314 ↗
11. A new approach of measurement and analysis of PVD-TiAlN coated carbide tools in machining of Monel 400 alloy under hybrid cooling conditions10.1016/j.measurement.2023.113428 ↗
12. Comprehensive analysis of tool wear, surface roughness and chip morphology in sustainable turning of Inconel-601 alloy10.1016/j.jmapro.2023.08.026 ↗
13. Implementation of green cooling/lubrication strategies in metal cutting industries: a state of the art towards sustainable future and challenges10.1016/j.susmat.2023.e00641 ↗
14. Experimental study on cryogenic milling performance of SiCp/Al composites with liquid nitrogen10.1080/10910344.2021.1971707 ↗
15. Production and characterization of AA6082-(Si3N4+ Gr) stir cast hybrid composites10.1080/02726351.2016.1143066 ↗
16. Taguchi design optimization of machining parameters on the CNC end milling process of halloysite nanotube with aluminium reinforced epoxy matrix (HNT/Al/Ep) hybrid composite10.1016/j.hbrcj.2013.09.007 ↗
17. Minimization of cutting force, temperature and surface roughness through GRA, TOPSIS and Taguchi techniques in end milling of Mg hybrid MMC10.1016/j.measurement.2017.11.011 ↗
18. Investigation on the mechanical and wear behaviour of Al-6082-BN-B4C-corn cob ash hybrid composites10.24874/ti.1165.08.21.11 ↗
19. End mill studies on Al6061 hybrid composite prepared by ultrasonic-assisted stir casting10.1007/s41939-020-00083-1 ↗
20. A study surface integrity of aluminum hybrid composites during milling operation10.1016/j.jmrt.2020.03.008 ↗
21. Machinability studies on Al 7075/BN/Al2O3 squeeze cast hybrid nanocomposite under different machining environments10.1080/10426914.2017.1401718 ↗
22. Investigation of the effects of cooling and lubricating strategies on tribological characteristics in machining of hybrid composites10.3390/lubricants10040063 ↗
23. Analysis and optimization of machinability of Al2O3 and fly ash reinforced aluminum hybrid composites using carbide inserts
24. Fabrication and mechanical characterization of Al 7050/TiO2/BN hybrid metal matrix composites10.1016/j.matpr.2020.06.386 ↗
25. Modeling and performance evaluation of Al2O3, MoS2 and graphite nanoparticle-assisted MQL in turning titanium alloy: an intelligent approach10.1007/s40430-020-2256-z ↗
26. New cooling approach and tool life improvement in cryogenic machining of titanium alloy Ti-6Al-4V10.1016/S0890-6955(01)00041-4 ↗
27. Hybrid cryogenic MQL for improving tool life in machining of Ti-6Al-4V titanium alloy10.1016/j.jmapro.2019.05.006 ↗
28. Wear under brittle removal regime of an under-expanded cryogenic nitrogen jet machining of bio-composites10.1016/j.wear.2021.203795 ↗
29. On the impacts of cutting parameters on surface roughness, tool wear mode and size in slot milling of A356 metal matrix composites reinforced with silicon carbide elements10.1177/0954405420937502 ↗
30. Tool wears in milling of Al/SiCp composites by dry and MQL milling
31. Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions10.1016/j.triboint.2021.107021 ↗
32. Machinability investigations on CFRP composites: a comparison between sustainable cooling conditions10.1007/s00170-021-07073-8 ↗
33. Grzesik · 2008
34. Hybrid machine learning-enabled multi-information fusion for indirect measurement of tool flank wear in milling10.1016/j.measurement.2022.112255 ↗
35. Estimation of surface roughness and flank wear in milling of inconel 625 superalloy10.1142/S0218625X21500116 ↗
36. Evaluation of machinability of Cu matrix composite materials by computer numerical control milling under cryogenic LN2 and minimum quantity lubrication10.1007/s11665-022-07262-w ↗
37. Role of CO2 cooling strategies in managing tool wear during the shoulder milling of grade 2 commercially pure titanium
38. Machinability investigations based on tool wear, surface roughness, cutting temperature, chip morphology and material removal rate during dry and MQL-assisted milling of Nimax mold steel10.3390/lubricants11030101 ↗
39. Sub-zero milling of Ti-6Al-4V—impact of the cutting parameters on the resulting forces, tool wear, and surface quality10.1007/s00170-023-11334-z ↗
40. Influence of hybrid nanofluid on tool wear and surface roughness in MQL-assisted face milling of AISI 5210010.1080/2374068X.2023.2210932 ↗
41. Dry and MQL milling of AISI 1045 steel with vegetable and mineral-based fluids10.3390/lubricants11040175 ↗
42. An investigation on performance of castor oil and Pongamia oil based cutting fluid in MQL milling of aluminium alloy 6061
43. Evaluation of tribological performance of MQL technique combined with LN₂, CO₂, N₂ ecological cooling/lubrication techniques when turning of Hastelloy C22 superalloy10.1016/j.triboint.2023.108786 ↗