journal article·2024-01Open access

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

Weichen Zhang, Jian Wang, Xiaolei Zhu, Xiaofeng Lu, Xiang Ling

Abstract

In this study, gas tungsten arc welding (GTAW) based dual wire additive manufacturing (D-WAAM) is adopted to fabricate the functionally graded material (FGM) from stainless steel (SS) 304 to Fe–40Al, using SS 304 and aluminum alloy (AA) 1070 wires. The Al/Fe atomic ratio varies from 0 to 40 % by varying the ratio of the wire feed speeds of the SS and AA wires. The chemical composition, phases, microstructure, and mechanical properties of the FGM are investigated. The results showed that with the increase of Al content, microstructures evolve as follows: γ-Fe → γ-Fe + α-Fe → α-Fe → Fe3Al → FeAl. Cracks occur in FeAl region, caused by the high stress and the low plasticity. Dislocation walls prevent the large grains from slipping, leading to the loss of plasticity. The microhardness of SS 304 to Fe–40Al FGM ranges from 188HV0.5 to 558HV0.5. As Al content increases, the ultimate compressive strength decreases from 1820 MPa to 1061 MPa. The results on microstructure and mechanical properties provide guidance for the preparation of steel - aluminum alloy FGMs.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Intermetallics and Advanced Alloy Properties · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Additive manufacturing of functionally graded material objects: a review10.1115/1.4039683 ↗
2. Advances in additive manufacturing of metal-based functionally graded materials10.1080/09506608.2019.1709354 ↗
3. Development and characterization of polymer–ceramic continuous fiber reinforced functionally graded composites for aerospace application10.1016/j.ast.2012.04.002 ↗
4. Microscopic control actions for distributed LaSMP patches laminated on paraboloidal thin shells
5. Additive manufacturing for energy: a review10.1016/j.apenergy.2020.116041 ↗
6. To improve total knee prostheses performance using three-phase ceramic-based functionally graded biomaterials10.3389/fmats.2019.00107 ↗
7. Microstructure and mechanical properties of TA15/TC11 graded structural material by wire arc additive manufacturing process10.1016/S1003-6326(21)65657-1 ↗
8. Fabrication and characterization of stainless steel 308 L/Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing10.1016/j.jallcom.2022.165398 ↗
9. Wire and arc additive manufacturing of 316L stainless steel/Inconel 625 functionally graded material: development and characterization10.1016/j.jmrt.2022.08.169 ↗
10. A functionally graded material from TC4 to 316L stainless steel fabricated by double-wire + arc additive manufacturing10.1016/j.matlet.2021.130141 ↗
11. Internal oxidation of Fe3Al during high temperature oxidation
12. The erosion-corrosion behavior of some Fe3Al-based alloys at high temperatures10.1016/S0043-1648(02)00046-7 ↗
13. Isothermal oxidation behavior of a sheet alloy of Fe-40at.%Al at temperatures between 1073 and 1473 K10.1016/S0966-9795(03)00067-0 ↗
14. Corrosion behavior of Fe-40Al sheet in N2-11.2O2-7.5CO2 atmospheres with various SO2 contents at 1273 K10.1016/S0966-9795(02)00190-5 ↗
15. Fabrication of Fe-FeAl functionally graded material using the wire-Arc Additive manufacturing process10.1007/s11663-015-0509-5 ↗
16. Evaluation of oxidation and hydrogen permeation in Al-containing stainless steel alloys10.1016/j.msea.2006.02.025 ↗
17. Effect of cooling rate on AlN precipitation in FeCrAl stainless steel during solidification10.3390/met9101091 ↗