journal article·2024-03Open access

High strength and electrical conductivity of nanostructured Cu–1Cr–0.1Zr alloy processed by multi–stage deformation and aging

Zhuqi Chu, Xuhao Pan, Wei Wei, Kunxia Wei, Igor V. Alexandrov, Xulong An, Dandan Wang, Xiangkui Liu

Abstract

The effects of equal channel angular pressing (ECAP), multiple cryogenic rolling and aging treatment on the microstructure, mechanical properties, and electrical conductivity of Cu–1Cr–0.1Zr alloy were investigated. The results showed that multi-stage deformation and aging (ECAP at ambient temperature + primary cryogenic rolling 50 % + 450 °C aging for 1h + secondary cryogenic rolling 80 % + 150 °C aging for 1h) can lead to the rational comprehensive performance of Cu–1Cr–0.1Zr alloy with tensile strength of 730 MPa and electrical conductivity of 75.5 % IACS. The microstructure characterization revealed that in the Cu–1Cr–0.1Zr alloy a subject to the multistage deformation and aging, there ultrafine grains, nanotwins, nanoprecipitates and micrometer precipitates constituted the nanostructured state. The increase in tensile strength was mainly attributed to fine grain strengthening and precipitation strengthening, followed by dislocation strengthening due to low temperature deformation. The ECAP resulted in the refinement of grain, and the increased dislocation density. The following primary cryogenic rolling refined the grains up to ultrafine-grained (UFG) size and created nanotwins. The introduction of nano-precipitated phases by intermediate aging pinned dislocations and impeded the motion of dislocation entanglements, allowing the alloy to achieve higher strength. Multi-stage deformation and aging resulted in a higher density of twin boundaries in the nanostructure and dilute solid solution in comparison with one stage treatment. These microstructural features were responsible for the excellent electrical conductivity.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Effect of chromium and zirconium content on structure, strength and electrical conductivity of Cu–Cr–Zr alloys after high pressure torsion10.1016/j.matlet.2017.04.039 ↗
2. Deformation microstructures, strengthening mechanisms, and electrical conductivity in a Cu–Cr–Zr alloy10.1016/j.msea.2015.01.065 ↗
3. Research on aging precipitation in a Cu–Cr–Zr–Mg alloy10.1016/j.msea.2004.09.041 ↗
4. Study on the variation of properties of Cu–Cr–Zr alloy by different rolling and aging sequence10.1016/j.msea.2020.140413 ↗
5. Microstructure evolution and properties of a Cu–Cr–Zr alloy with high strength and high conductivity10.1016/j.msea.2021.141464 ↗
6. Effects of Zr and (Ni, Si) additions on properties and microstructure of Cu–Cr alloy10.1016/j.jallcom.2013.08.146 ↗
7. Microstructure and properties of Cu–Zn–Cr–Zr alloy treated by multistage thermo-mechanical treatment10.1016/j.msea.2023.144679 ↗
8. Strengthening in high strength Cu–Cr–Zr–Ti alloy plates produced by hot rolling10.1016/j.msea.2016.07.063 ↗
9. Tailoring the microstructure of a Cu–0.7Cr–0.07Zr alloy submitted to ECAP at cryogenic temperature for improved thermal stability10.1016/j.matchar.2022.112045 ↗
10. Effect of heat treatment on low cycle fatigue properties of Cu–Cr–Zr alloy
11. Microstructure and properties of Cu–1.0Cr–0.2Zr–0.03Fe alloy10.1016/j.msea.2008.07.061 ↗
12. A multiscale architectured CuCrZr alloy with high strength, electrical conductivity and thermal stability10.1016/j.jallcom.2017.11.309 ↗
13. Sabirov · 2015 · 118
14. Grain refinement and enhanced precipitation of Cu–Cr–Zr induced by hot rolling with intermediate annealing treatment10.1016/j.jmrt.2019.06.019 ↗
15. Microstructure and strengthening mechanisms of CuCrZr alloy by two-step thermomechanical treatment10.1007/s10854-020-04333-3 ↗
16. A high strength and high electrical conductivity Cu–Cr–Zr alloy fabricated by cryorolling and intermediate aging treatment10.1016/j.msea.2016.10.087 ↗
17. Nanotwinned metallic materials
18. A high strength and high electrical conductivity bulk CuCrZr alloy with nanotwins10.1016/j.scriptamat.2014.11.032 ↗
19. Annealing behavior of ultra-low temperature rolled nano-twinned Cu–Zn–Si alloys
20. An effective method to obtain Cu–35Zn alloy with a good combination of strength and ductility through cryogenic rolling10.1016/j.msea.2018.01.014 ↗
21. Enhancing the strength and conductivity of commercialized Cu–Cr–Zr plate through simple high strain cold rolling and aging10.1016/j.matchar.2023.113213 ↗
22. Effect of deep cryogenic treatment on microstructure and properties of pure copper processed by equal channel angular pressing10.1002/adem.201801372 ↗
23. Mechanical properties and rolling behaviors of nano-grained copper with embedded nano-twin bundles10.1016/j.actamat.2008.01.030 ↗
24. Grain refinement and strengthening of a Cu–0.1Cr–0.06Zr alloy subjected to equal channel angular pressing10.1080/14786435.2017.1324649 ↗
25. History-independent cyclic response of nanotwinned metals10.1038/nature24266 ↗
26. Ce effects on dynamic recrystallization and microstructure of the copper alloy under hot deformation behavior with different strain rate10.1016/j.jmrt.2023.04.142 ↗
27. Precipitation, recrystallization, and evolution of annealing twins in a Cu-Cr-Zr alloy10.3390/met8040227 ↗
28. Optimization of strength, ductility and electrical conductivity of Cu–Cr–Zr alloy by combining multi-route ECAP and aging10.1016/j.msea.2015.09.111 ↗
29. High-strength AlCoCrFeNi2.1 eutectic high entropy alloy with ultrafine lamella structure via additive manufacturing10.1016/j.msea.2022.143816 ↗
30. Effects of Co and Si additions and cryogenic rolling on structure and properties of Cu–Cr alloys10.1016/j.msea.2018.10.093 ↗
31. Strengthening mechanisms in a high-strength bulk nanostructured Cu–Zn–Al alloy processed via cryomilling and spark plasma sintering10.1016/j.actamat.2012.09.036 ↗
32. Microstructure and properties of Cu–Cr–Nb alloy with high strength, high electrical conductivity and good softening resistance performance at elevated temperature10.1016/j.msea.2019.02.036 ↗
33. Microstructure and properties of a Cu–Ni–Si–Co–Cr alloy with high strength and high conductivity10.1016/j.msea.2019.05.003 ↗
34. Optimisation of strength and ductility of Cu–Cr–Zr by combining severe plastic deformation and precipitation10.1016/j.msea.2011.12.098 ↗
35. Effect of Ag addition on the microstructure and mechanical properties of Cu–Cr alloy10.1016/j.msea.2018.04.077 ↗
36. The influence of preaging on the strength and precipitation behavior of a deformed Al–Cu–Mg–Ag alloy10.1016/j.jallcom.2018.06.046 ↗
37. Modeling the electrical resistivity of deformation processed metal–metal composites10.1016/j.actamat.2014.06.013 ↗
38. Lu · 2007
39. Analysis of the effect of equal-channel angular pressing on the strength and electrical conductivity of low-alloyed alloys of the Cu–Cr–Zr system10.1088/1742-6596/1431/1/012065 ↗
40. Effect of rolling and aging processes on microstructure and properties of Cu–Cr–Zr alloy10.1016/j.msea.2017.05.114 ↗
41. Optimizing the strength, ductility and electrical conductivity of a Cu–Cr–Zr alloy by rotary swaging and aging treatment10.1016/j.msea.2019.01.002 ↗
42. Improved strength with good conductivity in Cu–Cr–Zr alloys: determinant effect of under-aging treatment before rolling and aging