journal article·2023-09Open access

Microstructure and mechanical properties of wire arc additive manufactured ZL205A alloy

Haijiang Liu, Zhiyong Cai, Yan Feng, Meng Wang

Abstract

The evolution of grain structure, precipitates and mechanical properties of the ZL205A alloy prepared by wire arc additive manufacturing were investigated. The results show that the as-deposited alloy consists of equiaxed and columnar grains in the bottom region. As the deposition height increases, the alloy mainly consists of equiaxed grains. The evolution of columnar to equiaxed grains is explained by the solidification theory. The needle-like θ'-Al2Cu precipitates in Cu-rich regions surrounding the α-Al+θ-Al2Cu eutectics. As the part deposited first is subjected to multiple cycles of heating by the subsequently deposited layers, the volume fraction and average size of θ' precipitates gradually decrease with the increase of deposition heights. The microhardness of the as-deposited alloy fluctuates in the range of 74.6-84.5 HV. The mechanical properties of the horizontal specimens at different heights are affected by the combination of grain structure, precipitates and pores, and that of the specimens in the middle region are optimal. The mechanical properties of the horizontal and vertical specimens show isotropic. Attributed to the grain boundary strengthening and precipitation strengthening, the yield strength (132.9 MPa) and elongation (15.9%) of the as-deposited alloy are approximately 31.3% and 211.8% higher than that of the as-cast alloy, respectively.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Wire arc additive manufacturing of aluminium alloys: a review
2. Wire plus arc additive manufacturing10.1179/1743284715Y.0000000073 ↗
3. A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement10.1016/j.jmapro.2018.08.001 ↗
4. A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium10.1080/02670836.2018.1455012 ↗
5. Microstructure, defects, and mechanical properties of wire plus arc additively manufactured Al-Cu4.3-Mg1.5 alloy10.1016/j.matdes.2019.108357 ↗
6. Microstructure and mechanical properties of AlSi7Mg0.6 aluminum alloy fabricated by wire and arc additive manufacturing based on cold metal transfer (WAAM-CMT)10.3390/ma12162525 ↗
7. TIG wire and arc additive manufacturing of 5A06 aluminum alloy
8. Welding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire10.1016/j.jallcom.2020.154987 ↗
9. Temperature-dependent constitutive behavior with consideration of microstructure evolution for as-quenched Al-Cu-Mn alloy10.1016/j.msea.2016.09.090 ↗
10. Al-rich region of Al-Cu-Mn10.1016/j.jallcom.2016.07.075 ↗
11. Machinability aspects of new Al–Cu alloys intended for automotive castings10.1016/j.jmatprotec.2010.06.006 ↗
12. Additive manufacturing in construction: a review on processes, applications, and digital planning methods
13. Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3% Cu alloy10.1007/s00170-014-6346-x ↗
14. Effect of heat input on microstructure and mechanical properties of Al-Mg alloys fabricated by WAAM10.1016/j.apsusc.2019.04.255 ↗
15. Effect of equivalent heat input on WAAM Al-Si alloy10.1016/j.ijmecsci.2022.107831 ↗
16. Study on microstructural and mechanical properties of an Al-Cu-Sn alloy wall deposited by double-wire arc additive manufacturing process
17. In situ synthesis of carbide reinforced Fe-Cu-Ni-Mo-Ti high entropy alloy coatings using GTAW cladding with cable-type welding wire10.1016/j.matlet.2022.132706 ↗
18. Pore formation and evolution in wire + arc additively manufactured 2319 Al alloy
19. Effect of Sn content on the microstructure and properties of wire and arc additive manufactured Al-Cu alloy deposits10.1089/3dp.2019.0176 ↗
20. Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy10.1016/j.matchar.2020.110735 ↗
21. The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al-6.3Cu alloy10.1016/j.msea.2015.10.101 ↗
22. Influence of travel speed on microstructure and mechanical properties of wire plus arc additively manufactured 2219 aluminum alloy10.1016/j.jmst.2019.06.016 ↗
23. The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 231910.1016/j.jmatprotec.2018.07.030 ↗
24. Effect of copper content on the tensile elongation of Al-Cu-Mn-Zr alloys: experiments and finite element simulations10.1016/j.msea.2019.138801 ↗
25. Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding10.1016/j.jmatprotec.2010.11.005 ↗
26. Wire arc additive manufacturing of Al-6Mg alloy using variable polarity cold metal transfer arc as power source10.1016/j.msea.2017.11.084 ↗
27. Wire-arc additive manufacturing of AZ31 magnesium alloy fabricated by cold metal transfer heat source: processing, microstructure, and mechanical behavior10.1016/j.jmatprotec.2020.116895 ↗
28. Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy
29. Coupled segregation mechanisms of Sc, Zr and Mn at θ′ interfaces enhances the strength and thermal stability of Al-Cu alloys10.1016/j.actamat.2021.116634 ↗
30. Microstructure and mechanical properties of ZL205A aluminum alloy wall produced by wire arc additive manufacturing
31. Microstructure evolution and mechanical behavior of 2219 aluminum alloys additively fabricated by the cold metal transfer process10.3390/ma11050812 ↗
32. Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al-Cu-Mn alloys10.1016/j.jallcom.2018.09.362 ↗
33. Effects of microalloying with Cd and Ag on the precipitation process of Al-4Cu-0.3Mg (wt&) alloy at 200 degrees C10.1016/S0968-4328(00)00093-7 ↗
34. Microstructure and mechanical properties of double-wire plus arc additively manufactured Al-Cu-Mg alloys10.1016/j.jmatprotec.2017.12.019 ↗
35. Mechanical properties of 2219-Al components produced by additive manufacturing with TIG
36. On the role of Zr content into Portevin-Le Chatelier (PLC) effect of selective laser melted high strength Al-Cu-Mg-Mn alloy10.1016/j.matlet.2019.03.112 ↗
37. Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: the comparison of as-deposited and T6 heat-treated samples10.1016/j.matchar.2022.111990 ↗
38. Effect of microstructure and strength on the fracture behavior of AA2219 alloy10.1016/j.msea.2008.11.024 ↗
39. Pore formation and evolution in wire plus arc additively manufactured 2319 Al alloy
40. Laser powder bed fusion of high-strength Sc/Zr-modified Al–Mg alloy: phase selection, microstructural/mechanical heterogeneity, and tensile deformation behavior10.1016/j.jmst.2021.03.069 ↗
41. Single-crystal laser deposition of superalloys: processing–microstructure maps10.1016/S1359-6454(00)00367-0 ↗
42. A mechanism for the formation of equiaxed grains in welds of aluminum–lithium alloy 209010.1016/S0921-5093(02)00858-4 ↗
43. Effects of Cd addition in welding wires on microstructure and mechanical property of wire and arc additively manufactured Al−Cu alloy10.1016/S1003-6326(22)65830-8 ↗
44. Precipitation phenomena and strengthening mechanism of Al–Cu alloys deposited by in-situ rolled wire-arc additive manufacturing10.1016/j.msea.2022.143770 ↗