Microstructure evolution and mechanical properties of high-strength aluminum alloy prepared by additive friction stir deposition
Source abstract
Abstract
Additive friction stir deposition (AFSD) is a solid-phase additive technology with promising development and application prospects. In this paper, the final AA7075 builds with five layers were successfully prepared using the AFSD process under both room and low temperature conditions, and the microstructure evolution and mechanical properties of the final builds were systematically studied. The build produced at room temperature exhibited an average grain size of 4.2–4.5 μm, primarily influenced by the rotated Cube texture. Whereas, the build produced at low temperature had an average grain size of 3.9–5.0 μm, dominated by the Brass, rotated Cu and rotated Goss components. The dislocation restoration was suppressed by the lower temperature environment, resulting in an increase in geometrically necessary dislocation density and a drop in recrystallization fraction. Due to the overgrowth of the strengthening phase, the hardness and tensile strength of the final builds decreased from the top layer to the bottom layer. Moreover, the lower temperature environment also inhibited the precipitation of the strengthening phase. This led to lower hardness and tensile strength compared to the build produced at room temperature. However, the elongation of the both builds exceeded 16 %, surpassing that of the AA7075-T6 feed bar. This study enhances the understanding of the relationship between microstructure and mechanical properties of additive friction stir deposited age-hardenable aluminum alloys, and provides an experimental reference and theoretical foundation for industrial additive manufacturing of high-performance aluminum alloys.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Additive manufacturing-A review10.1016/j.matpr.2021.05.181 ↗
2. Progress in additive manufacturing on new materials: a review10.1016/j.jmst.2018.09.002 ↗
3. Deformation mechanisms and mechanical properties of the high-strength and ductile Al-Zn-Mg-Cu alloys processed by repetitive continuous extrusion forming process with different heat treatments10.1016/j.jallcom.2023.171006 ↗
4. Development of bimodal grain-structured Al-Zn-Mg-Cu-Zr alloys for strength-ductility synergy via microalloying with Hf and Sc10.1016/j.matchar.2023.113349 ↗
5. Recent progress on the additive manufacturing of aluminum alloys and aluminum matrix composites: microstructure, properties, and applications10.1016/j.ijmachtools.2023.104047 ↗
6. Research trends in laser powder bed fusion of Al alloys within the last decade
7. A review on recent progress in solid state friction based metal additive manufacturing: friction stir additive techniques10.1080/10408436.2018.1490250 ↗
8. Experimental investigation on tool pin profile for defect-free multi-layered laminates using friction stir additive manufacturing10.1016/j.rineng.2023.101516 ↗
9. Influence of the kissing bond on the mechanical properties and fracture behaviour of AA5083-H112 friction stir welds10.1016/j.msea.2018.02.011 ↗
10. Effect of multi-layer deposition in solid-state friction stir surfacing-based additive manufacturing for fabrication of large-scale metal product10.1016/j.jmatprotec.2023.118107 ↗
11. Effect of preprocessing heat treatment of the Al-16Si-4Cu alloy on microstructure and tribological behavior of friction-surfaced coating10.1016/j.apsadv.2023.100564 ↗
12. Friction surfacing: a tool for surface crack repair10.1016/j.surfcoat.2021.127482 ↗
13. Additive friction stir deposition: a deformation processing route to metal additive manufacturing10.1080/21663831.2020.1847211 ↗
14. Deformation-based additive manufacturing of 7075 aluminum with wrought-like mechanical properties10.1016/j.matdes.2020.109288 ↗
15. Process-structure-property relations for as-deposited solid-state additively manufactured high-strength aluminum alloy
16. Precipitation behavior and strengthening-toughening mechanism of additive friction stir-deposited Al–Mg–Si–Cu alloy
17. Unveiling the mechanism of texture evolution in AZ31B Mg alloy during additive friction stir deposition10.1016/j.jallcom.2024.178404 ↗
18. Processing-structure-property correlation in additive friction stir deposited Ti-6Al-4V alloy from recycled metal chips
19. Additive friction stir deposition of SS316: effect of process parameters on microstructure evolution10.1016/j.matchar.2022.112470 ↗
20. A perspective on solid-state additive manufacturing of aluminum matrix composites using MELD10.1007/s11665-018-3649-3 ↗
21. Aluminum/steel dissimilar material with high interfacial strength manufactured by additive friction stir deposition10.1016/j.jmapro.2024.11.080 ↗
22. Interfacial corrosion behavior of aluminum/steel joints prepared by solid-state additive manufacturing10.1016/j.corsci.2024.112650 ↗
23. In situ investigation into temperature evolution and heat generation during additive friction stir deposition: a comparative study of Cu and Al-Mg-Si
24. Solid-state additive manufacturing of aluminum and copper using additive friction stir deposition: process-microstructure linkages10.1016/j.mtla.2020.100967 ↗
25. Effects of different cooling conditions on microstructure and precipitation behavior of fine-grained Al–Zn–Mg–Cu alloy friction stir welding joint10.1016/j.jmrt.2023.04.052 ↗
26. Effect of different cooling conditions on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys repaired by additive friction stir deposition10.1016/j.matchar.2024.114636 ↗
27. Correlation of local microstructures and mechanical properties of Al–Zn–Mg–Cu alloy build fabricated via underwater friction stir additive manufacturing10.1016/j.msea.2020.140590 ↗
28. A new grain orientation spread approach to analyze the dynamic recrystallization behavior of a cast-homogenized Mg-Zn-Zr alloy using electron backscattered diffraction10.1016/j.msea.2017.10.062 ↗
29. Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited 6061-T6 Al-Mg-Si alloy10.1016/j.jmrt.2023.07.097 ↗
30. Fine-grained aluminium crossover alloy for high-temperature sheet forming10.1016/j.actamat.2023.118952 ↗
31. Transmission electron microscopy investigation of separated nucleation and in-situ nucleation in AA7050 aluminium alloy10.1016/j.actamat.2018.02.045 ↗
32. Fine-grained AA 7075 processed by different thermo-mechanical processings10.1016/j.msea.2014.09.026 ↗
33. Microstructure and mechanical properties of Al–Li alloy manufactured by additive friction stir deposition10.1016/j.msea.2023.145753 ↗
34. A meshfree computational framework for the numerical simulation of the solid-state additive manufacturing process, additive friction stir-deposition (AFS-D)10.1016/j.matdes.2021.109514 ↗
35. Superior strength of laser-arc hybrid additive manufactured Al-Zn-Mg-Cu alloy enabled by a tunable microstructure
36. Microstructures and mechanical properties of Al–Zn–Mg aluminium alloy samples produced by wire + arc additive manufacturing10.1016/j.jmrt.2020.09.114 ↗
37. Effect of rotation speed on microstructure and mechanical anisotropy of Al-5083 alloy builds fabricated by friction extrusion additive manufacturing10.1016/j.msea.2022.144237 ↗
38. Additive friction stir deposition of AZ31B magnesium alloy10.1016/j.jma.2022.03.011 ↗
39. Clarification of microstructure evolution of aluminum during friction stir welding using liquid CO2 rapid cooling10.1016/j.matdes.2017.05.013 ↗
40. Interfacial grain structure, texture and tensile behavior of multilayer deformation-based additively manufactured Al 6061 alloy10.1016/j.matchar.2023.112646 ↗
41. Revisiting the precipitation mechanisms of Guinier-Preston zones, η′, and η precipitates in Al-Zn-Mg alloys10.1016/j.actamat.2024.119789 ↗
42. Experimental and first-principles characterization of heterogeneous nucleation of η on the E(Al18Mg3Cr2) phase in the 7075 Al alloys10.1016/j.jallcom.2023.172277 ↗
43. Atomic-scale investigation of the heterogeneous precipitation in the E (Al18Mg3Cr2) dispersoid of 7075 aluminum alloy10.1016/j.jallcom.2020.156890 ↗
44. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
45. Closed-loop temperature and force control of additive friction stir deposition
46. Recent advances in ageing of 7xxx series aluminum alloys: a physical metallurgy perspective10.1016/j.jallcom.2018.11.286 ↗
47. The effect of severe plastic deformation on precipitation in supersaturated Al–Zn–Mg alloys10.1016/j.msea.2007.01.001 ↗
48. A statistical theory of solid solution hardening10.1002/pssb.19700410221 ↗
49. Effects of processing paths on the microstructure, mechanical properties and electrical conductivity of dilute Al-Zr-Sc alloy conductive wires10.1016/j.jmst.2023.11.060 ↗
50. Mechanical behaviors and precipitation transformation of the lightweight high-Zn-content Al–Zn–Li–Mg–Cu alloy10.1016/j.msea.2020.140637 ↗
51. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
52. Experimental measurement of dislocation density in metallic materials: a quantitative comparison between measurements techniques (XRD, R-ECCI, HR-EBSD, TEM)10.1016/j.matchar.2023.112842 ↗
53. Geometrically necessary boundaries, incidental dislocation boundaries and geometrically necessary dislocations10.1016/S1359-6462(02)00358-5 ↗
54. Developing age-hardenable Al-Zr alloy by ultra-severe plastic deformation: significance of supersaturation, segregation and precipitation on hardening and electrical conductivity10.1016/j.actamat.2020.116503 ↗
55. Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al–Mn–Mg–Sc–Zr alloy processed by laser powder bed fusion10.1016/j.jmst.2023.11.033 ↗