journal article·2023-07Open access

Microstructural characterization and mechanical properties of additively manufactured 21-6-9 stainless steel for aerospace applications

Pragya Mishra, Pia Åkerfeldt, Fredrik Svahn, Erik Nilsson, Farnoosh Forouzan, Marta-Lena Antti

Abstract

The alloy 21-6-9 is a nitrogen-strengthened austenitic stainless steel often used in aerospace applications due to its high strength, good fabrication properties, and toughness at cryogenic temperatures. However, minimal research has been conducted on alloy 21-6-9 using the additive manufacturing process laser powder-bed fusion (L-PBF). The L-PBF technique has been seen as a key to reducing production time and avoiding costly machining. Therefore, there is an interest in investigating L-PBF-processed 21-6-9 to determine the effects of L-PBF on properties at elevated and cryogenic temperatures. In this study, prior to tensile testing the alloy 21-6-9 underwent heat treatments that simulated aerospace applications and the alloy was analyzed and characterized to evaluate phase stability. The effects of elevated and cryogenic temperatures (77 K) on the tensile behavior and microstructure were investigated using X-ray diffraction (XRD) and electron backscatter diffraction (EBSD). The tensile tests showed that the yield strength and ultimate tensile strength improved, while ductility varied depending on the conditions and test environment. The ultimate tensile strength was approximately 80% higher at 77 K than at room temperature, although the elongation decreased by around 90%, possibly due to the formation of strain-induced martensite.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. A review on metallurgical aspects of laser additive manufacturing (LAM): stainless steels, nickel superalloys, and titanium alloys10.1016/j.jmrt.2021.12.039 ↗
2. Increasing the productivity of laser powder bed fusion for stainless steel 316L through increased layer thickness10.1007/s11665-020-05334-3 ↗
3. Energy efficiency contributions and losses during selective laser melting10.2351/1.5040603 ↗
4. Microstructural characterization and mechanical properties of L-PBF processed 316 L at cryogenic temperature10.3390/ma14195856 ↗
5. Tensile properties of 21-6-9 austenitic stainless steel built using laser powder-bed fusion10.3390/ma14154280 ↗
6. Research status of laser additive manufacturing for metal: a review10.1016/j.jmrt.2021.08.050 ↗
7. On the relationship between laser scan strategy, texture variations and hidden nucleation sites for failure in laser powder-bed fusion10.1016/j.mtla.2022.101614 ↗
8. Additively manufactured hierarchical stainless steels with high strength and ductility10.1038/nmat5021 ↗
9. Deterioration in fracture toughness of 304LN austenitic stainless steel due to sensitization10.1007/s11661-009-0023-y ↗
10. Microstructural development in DED stainless steels: applying welding models to elucidate the impact of processing and alloy composition10.1007/s10853-020-05232-y ↗
11. Simultaneously enhanced strength and ductility for 3D-printed stainless steel 316L by selective laser melting10.1038/s41427-018-0018-5 ↗
12. Powder metallurgy of high nitrogen steels
13. Tech Steel & Materials. Stainless steel 21-6-9, https://www.techsteel.net/alloy/stainless-steel/21-6-9.
14. Overview: high-nitrogen alloying of stainless steels10.1016/0921-5093(95)09991-3 ↗
15. Cobelli · 2003 · 937
16. Effect of alloying elements and temperature on strength of cryogenic austenitic steels10.1016/S0921-5093(00)01796-2 ↗
17. Mechanical properties of inconel 625 welds in 21-6-9 stainless steel at 4K10.1016/0011-2275(79)90053-5 ↗
18. Microstructure and mechanical properties of 21-6-9 stainless steel electron beam welds10.1007/s11661-017-3996-y ↗
19. Torres · 1993
20. Nitrogen-containing 25Cr-13Ni stainless steel as a cryogenic structural material
21. Effect of hydrogen on cryogenic mechanical properties of Cr-Ni-Mn-N austenitic steels
22. Welding for cryogenic service
23. Yield stress of 21-6-9 stainless steel over very wide ranges of strain rates and temperatures10.1007/s11665-010-9818-7 ↗
24. Stress relief heat treatment and mechanical properties of laser powder bed fusion built 21-6-9 stainless steel10.1016/j.msea.2023.144742 ↗
25. Enhanced mechanical properties of a novel high-nitrogen Cr-Mn-Ni-Si austenitic stainless steel via TWIP/TRIP effects10.1007/s11661-009-9863-8 ↗
26. Dependence of grain size on mechanical properties and microstructures of high manganese austenitic steel10.1016/j.proeng.2014.09.141 ↗
27. Creep-damage assessment of high chromium heat resistant steels and weldments10.1016/j.msea.2008.08.045 ↗
28. Twinning induced plasticity in austenitic stainless steel 316L made by additive manufacturing10.1016/j.msea.2017.07.082 ↗
29. Exploiting process-related advantages of selective laser melting for the production of high-manganese steel10.3390/ma10010056 ↗
30. Twinning and martensite in a 304 austenitic stainless steel10.1016/j.msea.2012.05.080 ↗
31. Pilhagen · 2007
32. 2009
33. 2015
34. Thick-section weldments in 21-6-9 and 316LN stainless steel for fusion energy applications10.1016/0022-3115(92)90561-X ↗
35. Microstructure and corrosion evaluation of as-built and heat-treated 316L stainless steel manufactured by laser powder bed fusion10.1016/j.jmrt.2022.03.156 ↗
36. Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing10.1007/s00170-020-04972-0 ↗
37. Microstructure and hardness studies of inconel 718 manufactured by selective laser melting before and after solution heat treatment10.1016/j.msea.2017.02.062 ↗
38. Dislocation network in additive manufactured steel breaks strength–ductility trade-off10.1016/j.mattod.2017.11.004 ↗
39. A comprehensive study on microstructure and tensile behaviour of a selectively laser melted stainless steel10.1038/s41598-018-26136-7 ↗
40. High strength Fe–Mn–(Al, Si) TRIP/TWIP steels development — properties — application10.1016/S0749-6419(00)00015-2 ↗
41. Effects of processing and manufacturing of high nitrogen-containing stainless steels on their mechanical, corrosion and wear properties10.1016/S0924-0136(01)00804-4 ↗
42. Quantification of extremely small-structured ferritic-austenitic phase fractions in stainless steels manufactured by laser powder bed fusion10.1016/j.mtla.2022.101393 ↗
43. Hardened austenite steel with columnar sub-grain structure formed by laser melting10.1016/j.msea.2014.12.018 ↗
44. Selective laser melting of stainless steel 316L with low porosity and high build rates10.1016/j.matdes.2016.05.035 ↗
45. Correlation between process parameters, microstructure and properties of 316 L stainless steel processed by selective laser melting10.1016/j.msea.2018.01.103 ↗
46. Effect of heat treatment on mechanical properties and microstructure of selective laser melting 316L stainless steel10.1088/1757-899X/257/1/012021 ↗
47. Effect of the delta-ferrite content on the tensile properties in Nitronic 60 steel at room temperature and 750 °C
48. Non-destructive techniques for the detection of sigma phase in duplex stainless steel: a comprehensive review10.1016/j.engfailanal.2021.105227 ↗
49. Overview of intermetallic sigma (σ) phase precipitation in stainless steels10.5402/2012/732471 ↗
50. Delta ferrite in stainless steel weld metals10.1080/09507119209548267 ↗
51. Enhanced strength-ductility synergy of bimetallic laminated steel structure of 304 stainless steel and low-carbon steel fabricated by wire and arc additive manufacturing10.1016/j.msea.2022.143984 ↗
52. Post-treatment of additively manufactured Fe–Cr–Ni stainless steels by high pressure torsion: TRIP effect10.1016/j.msea.2021.141086 ↗
53. Grain boundary engineering during the laser powder bed fusion of TiC/316L stainless steel composites: new mechanism for forming TiC-induced special grain boundaries10.1016/j.actamat.2021.117605 ↗
54. Effect of special boundaries on γ → α transformation in austenitic stainless steel10.1134/S0031918X21040050 ↗
55. Formation of strain-induced martensite in selective laser melting austenitic stainless steel10.1016/j.msea.2018.10.121 ↗
56. High strength and ductility of additively manufactured 316L stainless steel explained10.1007/s11661-018-4607-2 ↗
57. Microstructure and mechanical properties of stainless steel 316L vertical struts manufactured by laser powder bed fusion process10.1016/j.msea.2018.08.069 ↗
58. About metastable cellular structure in additively manufactured austenitic stainless steels