Selective laser melting of Hastelloy-X alloy and cerium oxide reinforced Hastelloy-X composite: Microstructural examination and corrosion behavior
Source abstract
Abstract
The study investigated the microstructures and corrosion behaviors of Hastelloy X (HX) and HX reinforced by cerium oxide particles (HX-C) produced by selective laser melting (SLM) and compared to the wrought equivalent (HX-W). The aim was to eliminate hot cracking and investigate the HX's corrosion behavior in the presence of cerium oxide particles. The HX samples showed fine cellular and columnar solidification structures with uniform-size sub-cells and severe microcracking. Incorporating cerium oxide particles (1 wt.%) resulted in finer and relatively equiaxed grains without microcracking. The HX-W alloy contained a micron-sized carbide (Mo-rich M6C type) within the matrix. The HX-C sample displayed higher porosities compared to the HX sample (1.8 % against 0.3 %). Potentiodynamic polarization and electrochemical impedance spectroscopy tests were conducted in a standard NaCl solution at temperatures of 25, 50, and 70 °C to assess the corrosion behavior of Hastelloy samples. The HX-C matrix showed superior corrosion resistance compared to the HX-W and HX samples due to its finer grain structure and stable passive layer formation. Cerium oxide particles were found to be efficient in decreasing hot cracking and improving corrosion resistance.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (57)
Show source-provided references
1. Hot corrosion behaviour of Hastelloy X and Inconel 625 in an aggressive environment for superalloys for high-temperature energy applications10.1007/s13204-021-02077-y ↗
2. Microstructure and mechanical properties of Hastelloy X produced by HP-SLM (high power selective laser melting)10.1016/j.matdes.2019.107598 ↗
3. A defect-resistant Co–Ni superalloy for 3D printing10.1038/s41467-020-18775-0 ↗
4. Policy needed for additive manufacturing10.1038/nmat4658 ↗
5. Scientific, technological and economic issues in metal printing and their solutions10.1038/s41563-019-0408-2 ↗
6. Laser powder bed fusion of Hastelloy X: effects of hot isostatic pressing and the hot cracking mechanism10.1016/j.msea.2018.07.008 ↗
7. Anisotropic response in mechanical and corrosion properties of hastelloy X fabricated by selective laser melting10.1016/j.conbuildmat.2019.06.132 ↗
8. Micro-cracking, microstructure and mechanical properties of Hastelloy-X alloy printed by laser powder bed fusion: as-built, annealed and hot-isostatic pressed
9. Microscopic investigation of as built and hot isostatic pressed Hastelloy X processed by Selective Laser Melting10.1016/j.matchar.2019.05.024 ↗
10. Microstructure and hot tensile behavior of Hastelloy X superalloy laser powder-bed fusion-fabricated through different scanning patterns10.1016/j.msea.2023.144717 ↗
11. Study of the microstructure and cracking mechanisms of hastelloy X produced by laser powder bed fusion10.3390/ma11010106 ↗
12. Effects of Selective Laser Melting additive manufacturing parameters of Inconel 718 on porosity, microstructure and mechanical properties10.1016/j.msea.2018.08.037 ↗
13. Effect of processing routes on microstructural development, mechanical properties, and wear behavior of Ti6Al4V alloy
14. Influence of post heat treatments on anisotropy of mechanical behaviour and microstructure of Hastelloy-X parts produced by selective laser melting10.1016/j.msea.2016.04.086 ↗
15. Effect of minor alloying elements on crack-formation characteristics of Hastelloy-X manufactured by selective laser melting
16. Selective laser melting of Hastelloy X nanocomposite: effects of TiC reinforcement on crack elimination and strength improvement10.1016/j.compositesb.2020.108442 ↗
17. Insight to potential of TiB2 and CeO2 inoculants on microstructural evolution in laser powder bed fusion processed superalloy IN71810.1007/s11661-023-07247-x ↗
18. Electrochemical anisotropy of Hastelloy X fabricated by selective laser melting in a NaNO3 solution10.1016/j.jallcom.2023.169947 ↗
19. Effect of solution heat treatment on microstructure, mechanical and electrochemical properties of hastelloy X fabricated by laser powder bed fusion10.1016/j.jmrt.2023.03.108 ↗
20. Electrochemical behaviour of passivation film formed on SLM-fabricated Hastelloy X superalloy surface in 10 wt% NaNO3 solution10.1016/j.corsci.2022.110494 ↗
21. Passive and transpassive behaviour of Alloy 31 in a heavy brine LiBr solution10.1016/j.electacta.2013.02.024 ↗
22. Effect of grain refinement on tensile properties and electrochemical behavior of Fe-18.5%Cr ferritic stainless steel10.1016/j.matchemphys.2020.123089 ↗
23. Passive film breakdown at grain boundary junctions in high purity nickel
24. Electrochemical dissolution behavior of nickel-based hastelloy X superalloy at low current densities10.1109/ACCESS.2020.2983591 ↗
25. Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones10.1016/j.actamat.2016.02.014 ↗
26. A study of the microstructural evolution during selective laser melting of Ti–6Al–4V10.1016/j.actamat.2010.02.004 ↗
27. Analysis of defect generation in Ti–6Al–4V parts made using powder bed fusion additive manufacturing processes
28. Influence of defects on mechanical properties of Ti–6Al–4V components produced by selective laser melting and electron beam melting10.1016/j.matdes.2015.07.147 ↗
29. Additive manufacturing technologies of high entropy alloys (HEA): review and prospects10.3390/ma16062454 ↗
30. Cracking mechanism and control of Hastelloy X prepared by laser powder bed fusion10.1016/j.jmrt.2022.10.164 ↗
31. Phase precipitation and time–temperature-transformation diagram of Hastelloy X10.1016/S0921-5093(00)01049-2 ↗
32. Residual stresses in selective laser sintering and selective laser melting10.1108/13552540610707013 ↗
33. An investigation of hot cracking in Hastelloy-X
34. Effect of grain boundary fraction on castability of a directionally solidified nickel alloy10.1016/j.scriptamat.2006.02.032 ↗
35. Geddes · 2010
36. The effect of silicon on precipitation and decomposition behaviors of M6C carbide in a Ni–Mo–Cr superalloy10.1016/j.jallcom.2014.09.112 ↗
37. Hot tearing of nickel-based superalloys during directional solidification10.1016/S1359-6454(02)00042-3 ↗
38. Corrosion behavior of copper thin films deposited by EB-PVD technique on thermally grown silicon dioxide and glass in hydrochloric acid media
39. Corrosion mitigation ability of differently synthesized polypyrrole (PPy-FeCl3 & PPy-APS) conductive polymers modified with Na2MoO4 on mild steel in 3.5% NaCl solution: comparative study and optimization10.1016/j.corsci.2021.109894 ↗
40. Fabrication of Al5083-(CeO2-TiO2) hybrid surface composite via friction stir processing combined with plasma electrolytic oxidation
41. Corrosion inhibition of magnesium using biocompatible Alkyd coatings incorporated by mesoporous silica nanocontainers10.1016/j.porgcoat.2014.10.015 ↗
42. Application of mesoporous silica nanocontainers as an intelligent host of molybdate corrosion inhibitor embedded in the epoxy coated steel10.1016/j.pnsc.2017.02.005 ↗
43. Superhydrophobic surface of AZ31 alloy fabricated by chemical treatment in the NiSO4 solution10.1007/s11665-018-3479-3 ↗
44. The effect of mesoporous silica nanocontainers incorporation on the corrosion behavior of scratched polymer coatings10.1016/j.porgcoat.2015.11.006 ↗
45. An investigation on the corrosion behavior of the epoxy coating embedded with mesoporous silica nanocontainer loaded by sulfamethazine inhibitor10.1016/j.porgcoat.2018.12.022 ↗
46. Effect of temperature on passive film formation of UNS N08031 Cr – Ni alloy in phosphoric acid contaminated with different aggressive anions10.1016/j.electacta.2013.08.040 ↗
47. Influence of surface modifications on pitting corrosion behavior of nickel-base alloy 718 . Part 1 : effect of machine hammer peening10.1016/j.corsci.2013.08.007 ↗
48. Effect of annealing temperature on the microstructure evolution and corrosion behavior of Carbon-interstitial FeMnCoCrNi high-entropy alloys
49. Effect of temperature on the corrosion resistance and pitting behaviour of Alloy 31 in LiBr solutions10.1016/j.corsci.2008.03.016 ↗
50. Electrochemical and corrosion behavior of cast Re-containing inconel 718 alloys in sulphuric acid solutions and the effect of10.1016/S1452-3981(23)08171-3 ↗
51. Significantly enhanced corrosion resistance of Ni–Cu coating modified by minor cerium10.1016/j.corcom.2021.07.002 ↗
52. Fabrication of Al5083 surface composites reinforced by CNTs and cerium oxide nano particles via friction stir processing10.1016/j.jallcom.2014.10.158 ↗
53. Microstructure and wear performance of Al5083/CeO2/SiC mono and hybrid surface composites fabricated by friction stir processing10.1016/S1003-6326(18)64720-X ↗
54. Study of double layer rare earth metal conversion coating on aluminum alloy LY1210.1016/S0010-938X(00)00141-4 ↗
55. Reinforcing aluminium with cerium oxide: a new and effective technique to prevent corrosion in marine environments10.1016/j.elecom.2006.09.010 ↗
56. Development of cerium oxide and nickel oxide-incorporated aluminium matrix for marine applications10.1016/j.jallcom.2009.04.134 ↗
57. Influence of graphene oxide (GO) on microstructure and biodegradation of ZK30-xGO composites prepared by selective laser melting10.1016/j.jma.2019.10.004 ↗