On anisotropic tensile mechanical behavior of Al–Cu–Li AA2198 alloy under different ageing conditions
Source abstract
Abstract
The anisotropic mechanical behavior of Al–Cu–Li (AA2198) alloy under different artificial ageing conditions as well as for different thicknesses of the material was examined in the present investigation. Material characterization was performed for three different sheet directions, namely, longitudinal (0°), diagonal (45°) and transverse (90°) to the rolling direction. The results showed that the grain structure did not have significant changes by applying different artificial ageing times. In T3 heat treatment condition, only δ′ (Al3Li) phase was observed, while with increasing the ageing time, the major precipitates were T1 (Al2CuLi) phases. The latter was found to increase in size with artificial aging time. Almost similar yield strength values were observed for all investigated thicknesses, while the higher thickness specimens showed higher elongation at fracture values. Anisotropy was slightly higher at T3 condition, while the lowest anisotropy degree was noticed at the peak-aged condition. The specimens extracted in the diagonal direction showed high variation in mechanical properties, when compared with the respective results at the other two investigated directions, independently from the thickness of the specimens as well as from heat treatment condition. The smaller thickness specimens presented lower elongation at fracture values and for all investigated sheet directions, since they undergo plane stress conditions. Analysis of work hardening behavior showed that Bauschinger effect, which was not observed in T3 condition, became increasingly more prominent with artificial ageing time in all directions investigated.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. Application of modern aluminum alloys to aircraft10.1016/0376-0421(95)00004-6 ↗
2. The evolution of Al-Li base products for aerospace and space applications10.1007/s11661-012-1155-z ↗
3. Strength, deformation, fracture behaviour and ductility of aluminium-lithium alloys10.1007/BF00585420 ↗
4. Ageing response of a Al-Cu-li 2198 alloy10.1016/j.matdes.2014.04.063 ↗
5. Recent development in aluminium alloys for aerospace applications10.1016/S0921-5093(99)00674-7 ↗
6. Aluminium-lithium alloys10.1007/BF01132370 ↗
7. Assessment of the ability of conventional and advanced wrought aluminum alloys for mechanical performance in light-weight applications10.1016/j.matdes.2006.12.004 ↗
8. Recent developments in advanced aircraft aluminum alloys10.1016/j.matdes.2013.12.002 ↗
9. Weldability of Li-bearing aluminium alloys10.1179/095066099101528289 ↗
10. Transmission electron microscopy study of the evolution of precipitates in aged Al–Li–Cu alloys: the θ′ and T1 phases10.1016/S1359-6454(03)00253-2 ↗
11. Texture evolution behavior and anisotropy of 2A97 Al–Li alloy during recrystallization at elevated temperature
12. Effect of T1 precipitate on the anisotropy of Al-Li alloy 209010.1016/0956-7151(93)90028-Q ↗
13. Strength profile in Al-Li plate material10.1016/0036-9748(86)90138-9 ↗
14. Fabrication methods to manufacture isotropic Al-Li alloys and products for space and aerospace applications10.1016/S0921-5093(98)00827-2 ↗
15. Experimental investigation of tensile properties and anisotropy of 1420, 8090 and 2060 Al-Li alloys sheet undergoing different strain rates and fibre orientation: a comparative study10.1016/j.proeng.2017.10.730 ↗
16. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
17. Strengthening mechanisms of T1 precipitates and their influence on the plasticity of an Al-Cu-Li alloy10.1016/j.msea.2014.03.024 ↗
18. The plastic anisotropy of an Al-Li-Cu-Zr alloy extrusion in unidirectional deformation10.1007/BF02595442 ↗
19. Anisotropic deformation and damage in aluminium 2198 T8 sheets10.1177/1056789508101916 ↗
20. Anisotropic yielding stress of 2198 Al–Li alloy sheet and mechanisms10.1016/j.msea.2019.138572 ↗
21. Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al-Cu-Li alloy
22. 2013 · 1
23. A phenomenological hardening model for an aluminium-lithium alloy10.1016/j.ijplas.2019.02.009 ↗
24. 2011
25. Anisotropy and size effect in tensile mechanical properties of Al-Cu-Li 2198 alloy10.1016/j.prostr.2017.07.052 ↗
26. Al–Cu–Li and Al–Mg–Li alloys: phase composition, texture, and anisotropy of mechanical properties (Review)10.1134/S0036029516040042 ↗
27. Textures in industrial processes and products10.4028/www.scientific.net/MSF.702-703.18 ↗
28. The effect of Mn and Zr dispersoid-forming additions on recrystallization resistance in Al-Cu-Li AA2198 sheet10.1016/j.actamat.2014.05.028 ↗
29. Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA219810.1016/j.matchar.2021.111257 ↗
30. Precipitates and intermetallic phases in precipitation hardening Al–Cu–Mg–(Li) based alloys10.1179/174328005X14357 ↗
31. Microstructural evolution during ageing of Al–Cu–Li–x alloys10.1016/j.actamat.2013.12.001 ↗
32. Precipitation of T1 phase in 2198 Al-Li alloy studied by atomic-resolution HAADF-STEM10.1557/jmr.2019.136 ↗
33. Comparison of the effect of individual and combined Zr and Mn additions on the fracture behavior of Al-Cu-Li alloy AA2198 rolled sheet10.1007/s11661-013-2103-2 ↗
34. Evolution of grain boundary precipitates in an Al-Cu-Li alloy during aging10.1007/s11661-016-3848-1 ↗
35. Analysis of aluminium based alloys by calorimetry: quantitative analysis of reactions and reaction kinetics
36. Quantitative description of the T1 formation kinetics in an Al–Cu–Li alloy using differential scanning calorimetry, small-angle X-ray scattering and transmission electron microscopy10.1080/14786435.2013.878047 ↗
37. Microstructure mapping of a friction stir welded AA2050 Al–Li–Cu in the T8 state10.1080/14786435.2014.887862 ↗
38. A combined approach to microstructure mapping of an Al–Li AA2199 friction stir weld10.1016/j.actamat.2011.01.040 ↗
39. Aluminum-copper-lithium alloy 2050 developed for medium to thick plate10.1007/s11665-009-9554-z ↗
40. Thermomechanical treatment and corrosion resistance correlation in the AA2198 Al–Cu–Li alloy10.1080/1478422X.2019.1637077 ↗
41. Aging kinetics of friction stir welded Al-Cu-Li-Mg-Ag and Al-Cu-Li-Mg alloys10.1016/j.matdes.2016.07.126 ↗
42. The influence of precipitation on plastic deformation of Al-Cu-Li alloys10.1016/j.actamat.2013.03.015 ↗
43. Influence of the rolling direction on the microstructure, mechanical, anisotropy and gamma rays shielding properties of an Al-Cu-Li-Mg-X alloy10.1016/j.msea.2018.06.074 ↗
44. Abbaschian · 2008
45. Effect of heat treatment on the microstructure and mechanical properties of extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr alloy10.1016/j.msea.2018.01.063 ↗
46. Laws for work-hardening and low-temperature creep10.1115/1.3443340 ↗
47. Kinetics of flow and strain-hardening10.1016/0001-6160(81)90112-7 ↗
48. The effect of solution treatment and artificial aging on the work hardening characteristics of a cast Al–7%Si–0.6%Mg alloy10.1016/j.msea.2006.04.011 ↗
49. The effect of artificial aging on tensile work hardening characteristics of a cast Al-7 Pct Si-0.55 Pct Mg (A357) alloy10.1007/s11661-008-9611-5 ↗
50. The effect of structural integrity on the tensile deformation characteristics of A206-T71 alloy castings10.1016/j.msea.2007.11.005 ↗
51. The influence of precipitation on the work-hardening behavior of the aluminum alloys AA6111 and AA703010.1007/s11661-003-0007-2 ↗
52. Physics and phenomenology of strain hardening: the FCC case10.1016/S0079-6425(02)00003-8 ↗
53. The effect of remelting on the melt and casting quality in Al–7%Si–Mg castings10.1016/j.msea.2014.03.032 ↗