journal article·2023-05Open access

Effects of tempering temperature on the microstructure evolution and mechanical properties of 16%Cr–5%Ni super martensitic stainless steel

Yisi Song, Chuanwei Li, Yu Liao, Lizhan Han, Jianfeng Gu

Abstract

The effects of tempering temperature on the microstructure evolution and mechanical properties of 16%Cr–5%Ni super martensitic stainless steel (SMSS) were investigated in the present study. Reversed austenite was detected via X-ray diffraction when the as-quenched samples with full martensite were tempered above 500 °C, and its volume fraction attained a maximum of ∼17% at 620 °C. When tempered below 620 °C, all the reversed austenite formed was able to keep stable at room temperature, while partial or even entire reversed austenite formed above 640 °C with Ni content less than 8 wt% transformed back into fresh martensite during cooling, demonstrating that the enrichment of Ni determined the thermal stability of reversed austenite. EDS results revealed that the precipitation of M23C6 carbides caused Ni enrichment in the adjacent regions, promoting the nucleation of reversed austenite, and the growth of reversed austenite was mainly controlled by Ni diffusion. The results of tensile tests and instrumented impact tests indicated that stable reversed austenite effectively improved the ductility and toughness, and offset the deterioration of toughness caused by the M23C6 precipitating at grain boundaries. Tempering at 540 °C achieved an excellent combination of strength and toughness, while the best plasticity of samples was obtained by tempering at 620 °C.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Impact of reversed austenite on the pitting corrosion behavior of super 13Cr martensitic stainless steel10.1016/j.electacta.2016.01.094 ↗
2. Corrosion behavior of supermartensitic stainless steel in aerated and CO2-saturated synthetic seawater10.1016/j.msea.2006.04.107 ↗
3. Corrosion and metallurgical investigation of two supermartensitic stainless steels for oil and gas environments10.1016/j.corsci.2013.12.015 ↗
4. The effects of temperature and hydrodynamics on the CO2 corrosion of 13Cr and 13Cr5Ni2Mo stainless steels in the presence of free acetic acid10.1016/j.corsci.2004.05.020 ↗
5. Studies on Nb microalloying of 13Cr super martensitic stainless steel10.1007/s11661-012-1268-4 ↗
6. Influence of heat treatments on toughness and sensitization of a Ti-alloyed supermartensitic stainless steel10.1007/s10853-011-5753-8 ↗
7. Effect of Cu addition on microstructure and mechanical properties of 15%Cr super martensitic stainless steel10.1016/j.matdes.2012.04.036 ↗
8. Microstructural evolution and low temperature impact toughness of a Fe–13%Cr–4%Ni–Mo martensitic stainless steel10.1016/j.msea.2009.08.022 ↗
9. The influence of tempering temperature on the reversed austenite formation and tensile properties in Fe–13%Cr–4%Ni–Mo low carbon martensite stainless steels10.1016/j.msea.2011.01.078 ↗
10. Microstructure and properties of 13Cr5Ni1Mo0.025Nb0.09V0.06N super martensitic stainless steel10.1016/j.msea.2012.01.093 ↗
11. Characteristics and effects of austenite resulting from tempering of 13Cr–NiMo martensitic steel weld metals10.1016/S1044-5803(00)00099-1 ↗
12. Hot workability of 00Cr13Ni5Mo2 supermartensitic stainless steel10.1016/j.matdes.2011.03.067 ↗
13. Microstructural and mechanical characterization of radial friction welded supermartensitic stainless steel joints10.1016/j.msea.2013.08.014 ↗
14. Microstructure evolution and orientation relationship of reverted austenite in 13Cr supermartensitic stainless steel during the tempering process
15. Advances in the making and base material properties of supermartensitic stainless steels (SMSS)
16. Effect of heat treatment on reversed austenite in Cr15 super martensitic stainless steel10.1016/S1006-706X(13)60099-0 ↗
17. In-situ determination of austenite and martensite formation in 13Cr6Ni2Mo supermartensitic stainless steel10.1016/j.matchar.2012.06.004 ↗
18. Influence of retained austenite on the mechanical properties of low carbon martensitic stainless steel castings10.2355/isijinternational.51.471 ↗
19. Reversed austenite growth behavior of a 13%Cr-5%Ni stainless steel during intercritical annealing10.2355/isijinternational.ISIJINT-2015-280 ↗
20. Investigation of the evolution of retained austenite in Fe–13%Cr–4%Ni martensitic stainless steel during intercritical tempering10.1016/j.matdes.2015.06.143 ↗
21. Study on the crystallographic orientation relationship and formation mechanism of reversed austenite in economical Cr12 super martensitic stainless steel10.1016/j.matchar.2015.09.013 ↗
22. Carbon partitioning into austenite after martensite transformation10.1016/S1359-6454(03)00059-4 ↗
23. Tailoring the metastable reversed austenite from metastable Mn-rich carbides10.1016/j.actamat.2021.116986 ↗
24. Ensuring combination of strength, ductility and toughness in medium-manganese steel through optimization of nano-scale metastable austenite10.1016/j.matchar.2017.11.058 ↗
25. On the thermal and mechanical stability of reverted austenite by intercritical tempering10.1016/j.matlet.2021.129457 ↗
26. Reversed austenite in 0Cr13Ni4Mo martensitic stainless steels10.1016/j.matchemphys.2013.10.006 ↗
27. Bhadeshia · 2017 · 343
28. Effects of cooling path and resulting microstructure on the impact toughness of a hot stamping martensitic stainless steel10.1016/j.msea.2018.11.036 ↗
29. The effects of carbon contents and ms temperatures on the hardness of martensitic Fe-Ni-C alloys10.2355/isijinternational1966.12.16 ↗
30. Structure–mechanical property relationship in low carbon microalloyed steel plate processed using controlled rolling and two-stage continuous cooling10.1016/j.msea.2013.07.071 ↗
31. Stabilization of retained austenite by the two-step intercritical heat treatment and its effect on the toughness of a low alloyed steel10.1016/j.matdes.2014.02.035 ↗
32. Effect of alloying additions on the lattice parameter of austenite
33. Segregation engineering enables nanoscale martensite to austenite phase transformation at grain boundaries: a pathway to ductile martensite10.1016/j.actamat.2013.06.055 ↗
34. Formation of the reversed austenite during intercritical tempering in a Fe–13%Cr–4%Ni–Mo martensitic stainless steel10.1016/j.matlet.2010.03.021 ↗
35. Song · 2011
36. Austenite grain size and the martensite-start temperature10.1016/j.scriptamat.2008.11.043 ↗
37. Austenite stability of ultrafine-grained transformation-induced plasticity steel with Mn partitioning10.1016/j.scriptamat.2011.04.010 ↗
38. Phase identification in an isothermally aged austenitic 22Cr-21Ni-6Mo-N stainless steel10.1016/S1359-6462(98)00269-3 ↗
39. Precipitation of M23C6 in austenitic steels10.1016/0001-6160(65)90053-2 ↗
40. Effect of tempering process on the cryogenic impact toughness of 13Cr4NiMo martensitic stainless steel10.1016/j.jmrt.2023.02.182 ↗
41. On the interaction of cleavage cracks with second phase particles10.1016/0001-6160(75)90189-3 ↗
42. The determining role of reversed austenite in enhancing toughness of a novel ultra-low carbon medium manganese high strength steel10.1016/j.scriptamat.2015.04.009 ↗