Effects of ECAP and subsequent recovery on microstructure, mechanical, tribological and corrosion properties of Ti–6Al–4V alloy
Source abstract
Abstract
Ti–6Al–4V alloy is widely used in various industries such as aerospace and biomedical engineering . This article reports a study on effects of the equal channel angular pressing (ECAP) and subsequent recovery on microstructure, mechanical, tribiological, and corrosion properties of the alloy. The two passes of ECAP process were done at 540 °C with 120 ° inner angle and subsequent recovery was carried out at 340 °C for 1 h. Microstructure was examined with optical microscope , scanning electron microscope and transmission electron microscope. The mechanical properties and corrosion behavior were evaluated with compressive and polarization dynamic tests, respectively. The wear resistance was determined with scratching test, and the volume loss was measured with a profilometer. Obtained results show that the ECAP-recovery (i.e. ECAP + recovery) sample exhibits improved properties than the as-received one (annealed) and ECAP (ECAP treated) samples. The corrosion tests indicate that the ECAP sample has its corrosion resistance higher than that of the as-received one but lower than that of the ECAP-recovery sample. ECAP-recovery sample has the highest resistance to wear and corrosive wear among the three samples.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Perspectives on titanium science and technology10.1016/j.actamat.2012.10.043 ↗
2. Microstructure and mechanical properties of additively manufactured Ti–6Al–4V alloy based on large area, high-resolution EBSD mapping10.1016/j.jmrt.2024.10.020 ↗
3. Ti based biomaterials, the ultimate choice for orthopedic implants–a review10.1016/j.pmatsci.2008.06.004 ↗
4. A new look at biomedical Ti-based shape memory alloys10.1016/j.actbio.2012.01.018 ↗
5. Titanium as a metal for implantation. Part 2: biological and clinical applications
6. 2014 · p68
7. 1986
8. Surface properties determine bioadhesive outcomes: methods and results10.1002/jbm.820180404 ↗
9. Adhesion: mechanisms that Assist or Impede It: an interdisciplinary approach relates present knowledge of adhesion to bioadhesional problems10.1126/science.162.3860.1360 ↗
10. Albrektsson · 1991
11. Material considerations
12. Wear characteristics of Ti–Nb–Ta–Zr and Ti–6Al–4V alloys for biomedical applications10.1016/j.wear.2004.04.001 ↗
13. Titanium: Physical metallurgy
14. Twenty-five years of ultrafine-grained materials: achieving exceptional properties through grain refinement10.1016/j.actamat.2013.08.018 ↗
15. A review on high-pressure torsion (HPT) from 1935 to 198810.1016/j.msea.2015.11.074 ↗
16. Principles of equal-channel angular pressing as a processing tool for grain refinement10.1016/j.pmatsci.2006.02.003 ↗
17. Residual stress, fatigue behavior, and mechanical properties of equal-channel angular pressed commercial pure titanium10.1016/j.jmrt.2023.12.265 ↗
18. The effect of equal-channel angular pressing on the structure and mechanical behavior of Ti–6Al–4V alloy10.1016/j.msea.2004.02.093 ↗
19. Producing bulk ultrafine-grained materials by severe plastic deformation: ten years later10.1007/s11837-016-1820-6 ↗
20. Microstructural approach to equal channel angular processing of commercially pure titanium—a review10.1016/S1003-6326(15)63734-7 ↗
21. Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP10.1016/j.jmrt.2023.12.273 ↗
22. Microstructure evolution and mechanical properties of Ti-6Al-4V alloy prepared by multipass equal channel angular pressing10.1007/s11665-020-04673-5 ↗
23. Mechanical and microstructural variations in ECAP of Ti–6Al–4V alloy with equiaxed microstructure10.1007/s12598-018-1071-5 ↗
24. Achieving ultra-fine grains and high corrosion resistance of Al–Zn–Mg–Cu alloy by ECAP and post cold rolling10.1016/j.jmrt.2023.09.070 ↗
25. Microstructural homogeneity, texture and corrosion properties of RE-doped 55Mg-35Pb-9.2 Al-0.8 B alloy fabricated via equal channel angular pressing (ECAP)10.1016/j.jallcom.2023.171607 ↗
26. Effect of surface nanocrystallization on the corrosion behavior of Ti–6Al–4V titanium alloy10.1016/j.surfcoat.2013.02.052 ↗
27. Enhanced corrosion behavior of ultrafine-grained pure titanium in simulated high-temperature seawater10.1016/j.jmrt.2022.05.032 ↗
28. Commercially pure titanium modification to enhance corrosion behavior and osteoblast response by ECAP for biomedical applications
29. Tribological properties of ultrafine-grained materials processed by severe plastic deformation10.1007/s10853-011-6231-z ↗
30. Reduction of friction coefficient of ultrafine-grained CP titanium10.1016/j.msea.2003.12.026 ↗
31. Dry sliding wear behavior of TiNi alloy processed by equal channel angular extrusion10.1016/j.matdes.2006.06.012 ↗
32. Structural transformations, strengthening, and wear resistance of titanium nickelide upon abrasive and adhesive wear10.1134/S0031918X10070112 ↗
33. Effect of cryogenic treatment on wear resistance of Ti–6Al–4V alloy for biomedical applications10.1016/j.jmbbm.2013.11.003 ↗
34. Wear behavior of an aluminum alloy processed by equal-channel angular pressing10.1007/s10853-010-4862-0 ↗
35. Low sliding-wear resistance of ultrafine-grained Al alloys and steel having undergone severe plastic deformation10.3139/146.110109 ↗
36. Does severe plastic deformation (SPD) alone generate a nano-crystallinestructure?10.1080/09500831003662537 ↗
37. High‐cycle fatigue behavior of an ultrafine‐grained Ti–6Al–4V alloy processed by ECAP and extrusion10.1002/adem.201500630 ↗
38. Surface nanocrystallization by sandblasting and annealing for improved mechanical and tribological properties10.1088/0957-4484/16/12/040 ↗
39. A simple surface treatment for Mg to gain enhanced resistance to corrosion and corrosive wear by hammering Al powder-covered Mg substrate
40. Tribocorrosion behaviour of nanostructured titanium substrates processed by high-pressuretorsion10.1088/0957-4484/21/48/485703 ↗
41. Effects of prior cold work on corrosion and corrosive wear of copper in HNO3 and NaCl solutions10.1016/j.msea.2004.11.054 ↗
42. The evolution mechanism of tribo-oxide layer during high temperature dry sliding wear for nickel-based superalloy10.1016/j.wear.2021.203747 ↗
43. Hutchings · 2017
44. Application of an electrochemical scratch technique to evaluate contributions of mechanical and electrochemical attacks to corrosive wear of materials10.1016/j.wear.2005.02.041 ↗
45. Development of novel tribo composites with TiNi shape memory alloy matrix10.1016/S0043-1648(03)00116-9 ↗
46. Recent progress on wear‐resistant materials: designs, properties, and applications10.1002/advs.202003739 ↗
47. Development of a new wear-resistant material: TiC/TiNi composite10.1016/S1359-6462(99)00236-5 ↗
48. A microscale dynamical model for wear simulation10.1016/S0043-1648(98)00368-8 ↗
49. A finite element approach to modeling abrasive wear modes10.1080/10402004.2016.1206647 ↗
50. Effects of 3D printed surface texture on erosive wear10.1016/j.triboint.2019.106110 ↗
51. Microstructure and mechanical properties of Mg-to-Al dissimilar welded joints with an Ag interlayer using ultrasonic spot welding10.1016/j.jma.2020.04.001 ↗
52. Budinski · 2021
53. Effect of deep cryogenic treatment on machinability and wear mechanism of TiAlN coated tools during dry turning10.1007/s12541-014-0384-z ↗
54. Effects of cathodic protection on corrosive wear of 304 stainless steel10.1007/s11249-004-3205-1 ↗
55. Effect of annealing treatment on mechanical properties of nanocrystalline α-iron: an atomistic study10.1038/srep08459 ↗
56. A novel hybrid micro-texture for improving the wear resistance of PCD tools on cutting SiCp/Al composites10.1016/j.jmapro.2023.06.027 ↗
57. 2013
58. Review of novel high-entropy protective materials: wear, irradiation, and erosion resistance properties10.3390/e25010073 ↗