journal article·2025-05Open access

The effect of Zr element on the microstructure and properties of Cu–Ni–Si alloys

Fuqiang Liu, Xiao Zhang, Xiaocui Zhang, Qing Liu, Fugong Qi, Chunyan Li, Liang Chen, Haimin Ding

Abstract

In order to investigate the effect of Zr addition on Cu–Ni–Si alloys, this study developed four Cu–Ni–Si-(Zr) alloys with different Zr contents based on the Cu-3.2Ni-0.7Si alloy and systematically analyzed their microstructure and property variations. After undergoing the same deformation and heat treatment processes, it was found that, in addition to Ni 2 Si, the alloy also formed the intermetallic compound Ni 16 Zr 6 Si 7 . As the Zr content increased, the activation energy for Ni 2 Si precipitation gradually decreased, leading to an increased precipitation rate. Meanwhile, the particle size and content of Ni 16 Zr 6 Si 7 also increased. During hot rolling, Ni 16 Zr 6 Si 7 promotes the nucleation Cu grain recrystallization and pins the grain boundaries, leading to a gradual reduction in grain size. This reduction in grain size contributes to improved plasticity and toughness of the alloy. However, due to the relatively large particle size, the formation of Ni 16 Zr 6 Si 7 has a smaller strengthening effect on the alloy. The increase in alloy strength primarily relies on the precipitation strengthening provided by the nano-sized Ni 2 Si formed during heat treatment. Therefore, when the Zr content is 0.05 wt%, the strengthening effect of Ni 2 Si is significantly improved compared to the Cu-3.2Ni-0.7Si alloy, while the precipitation of Ni 16 Zr 6 Si 7 particles remains relatively low, resulting in the best overall performance of the alloy. After aging at 450 °C for 6h, the peak hardness of Cu-3.2Ni-0.7Si-0.05Zr reaches 270.1HV, with conductivity of 37 %IACS, tensile strength of 692.5 MPa, and elongation of 10.1 %.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. High strength and high electrical conductivity Cu-Cr system alloys manu-factured by hot rolling-quenching process and thermomechanical treatments10.1016/j.msea.2012.01.047 ↗
2. A DSC analysis of thermodynamic properties and solidification characteristics for binary Cu-Sn alloys10.1016/j.actamat.2012.08.013 ↗
3. Effect of small amount addition of Co on dynamic recrystallization of Cu-Be alloys10.2320/matertrans1989.36.1023 ↗
4. Achieving high strength and high-electrical-conductivity of Cu-Ni-Si alloys via regulating nanoprecipitation behavior through simplified process10.1016/j.jmst.2024.07.039 ↗
5. Microstructure and properties of TiC-Ti5Si3 reinforced copper matrix composites10.1016/j.ceramint.2023.08.114 ↗
6. Effect of small amount addition of Co on dynamic recrystallization of Cu-Be alloys10.2320/matertrans1989.36.1023 ↗
7. Effects of Zr and (Ni, Si) additions on properties and microstructure of Cu-Cr alloy10.1016/j.jallcom.2013.08.146 ↗
8. Impression creep study of a Cu-0.3Cr-0.1Ag alloy10.1016/j.msea.2010.01.044 ↗
9. Mechanical properties of Cu-Cr system alloys with and without Zr and Ag10.1007/s10853-007-2159-8 ↗
10. Study on high-strength and high-conductivity Cu-Fe-P alloys10.1016/j.msea.2006.01.068 ↗
11. A new ultrahigh strength Cu-Ni alloy10.1016/j.intermet.2013.05.013 ↗
12. Effect of ther-momechanical treatment on spray formed Cu-Ni-Si alloy10.1179/026708304225017265 ↗
13. Araki · 2015
14. Precipitation behavior of Cu-3.0 Ni-0.72 Si alloy10.1016/j.actamat.2018.12.047 ↗
15. Research and development of advanced copper matrix composites10.1016/S1003-6326(24)66641-0 ↗
16. Effects of B and Y additions on the microstructure and properties of Cu-Mg-Te alloys10.1557/jmr.2013.266 ↗
17. Wire-based friction stir additive manufacturing towards isotropic high-strength-ductility Al-Mg alloys10.1080/17452759.2024.2417369 ↗
18. Effect of hot-rolling process on the microstructure, mechanical and corrosion behaviors of dual-phase Co-based entropic alloys10.1016/j.msea.2024.147433 ↗
19. Effect of electropulsing treatment on the microstructure and mechanical properties of Ti6Al4V alloy processed by a hybrid method of directed energy deposition and layer-by-layer ultrasonic impact peening10.1016/j.msea.2024.146774 ↗
20. Dynamic embrittlement at intermediate temperature in a Cu-Ni-Si alloy10.1016/j.msea.2007.05.013 ↗
21. Simultaneous enhancement of mechanical and electrical properties of Cu-Ni-Si alloys via thermo-mechanical process10.1016/j.msea.2022.142815 ↗
22. Effects of small addition of Ti on strength and microstructure of a Cu-Ni-Si alloy10.1007/s11661-015-2870-z ↗
23. Effect of Ti addition on tensile properties of Cu-Ni-Si alloys10.1007/s12540-011-0807-7 ↗
24. Effects of Ti addition and heat treatments on mechanical and electrical properties of Cu-Ni-Si alloys10.1007/s12540-013-1011-8 ↗
25. Mechanical properties of Cu-4.0 wt%Ni-0.95 wt%Si alloys with and without P and Cr addition10.4028/www.scientific.net/MSF.561-565.2321 ↗
26. Effect of V addition on hardness and electrical conductivity in Cu-Ni-Si alloys10.1007/s12540-013-4002-x ↗
27. Evolution of microstructure and properties of an ultra high strength Cu-Ni-Sn alloy with low Sn content during the multi-stage thermomechanical treatment10.1016/j.msea.2023.144933 ↗
28. Effect of TiC particle size on the microstructure and properties of CuCr-TiC composites manufactured by powder metallurgy10.1016/j.compstruct.2024.118323 ↗
29. Precipitation behavior of a new Cu-Ni-Co-Si-Fe-Mg alloy designed with low cobalt content10.1016/j.matdes.2024.112833 ↗
30. Mechanical properties of Cu-4.0 wt%Ni-0.95 wt%Si alloys with and without P and Cr addition10.4028/www.scientific.net/MSF.561-565.2321 ↗
31. Effect of V addition on hardness and electrical conductivity in Cu-Ni-Si alloys10.1007/s12540-013-4002-x ↗
32. The two-step nucleation of G-phase in ferrite10.1016/j.actamat.2016.06.013 ↗
33. Effects of small addition of Ti on strength and microstructure of a Cu-Ni-Si alloy10.1007/s11661-015-2870-z ↗
34. Effect of Ti addition on tensile properties of Cu-Ni-Si alloys10.1007/s12540-011-0807-7 ↗
35. Hot deformation and dynamic recrystallization behavior of Cu-3Ti-3Ni-0.5Si alloy10.1016/j.jallcom.2018.12.212 ↗
36. Effects of Ti addition and heat treatments on mechanical and electrical properties of Cu-Ni-Si alloys10.1007/s12540-013-1011-8 ↗
37. Microstructure and properties of high-strength Cu-Ni-Si-(Ti) alloys10.1007/s12598-020-01699-5 ↗
38. On the crystal structure of the Mn-Ni-Si G-phase10.1016/j.jallcom.2008.01.142 ↗
39. Development of novel ferritic steels strengthened by the Co16X6Si7-G phase: a theoretical and experimental study
40. Investigation of the orientation relationship between nano-sized G-phase precipitates and austenite with scanning nano-beam electron diffraction using a pixelated detector10.1016/j.scriptamat.2021.113930 ↗
41. New insights into the precipitation strengthening of ferritic steels: nanoscale G-phase particle10.1016/j.matlet.2017.07.078 ↗
42. Development of high-strength martensite by age-hardening of coherent intermetallic precipitates
43. Microstructural evolution and precipitation strengthening in a new 20Cr ferritic trial steel10.1016/j.msea.2018.05.027 ↗
44. Effect of Ni, Mo and Mn content on spinodal decomposition kinetics and G-phase precipitation of aged model cast austenitic stainless steels10.1016/j.jnucmat.2021.153123 ↗
45. Enhanced strength and electrical conductivity of Cu-Zr-B alloy by double deformation-aging process10.1016/j.jallcom.2014.07.010 ↗
46. Development of nano-structure Cu-Zr alloys by the mechanical alloying process10.1016/j.jallcom.2010.08.071 ↗
47. X-ray diffraction line profile analysis for defect study in Cu-1wt% Cr-0.1wt% Zr alloy10.1016/j.matchar.2004.09.009 ↗
48. Effect of inclusion on strength and conductivity of Cu-Ni-Si alloys with discontinuous precipitation10.1016/j.jallcom.2020.156006 ↗
49. Effect of aluminum on microstructure and property of Cu-Ni-Si alloys10.1016/j.msea.2013.02.024 ↗
50. Effect and mechanism of room temperature rolling, cryogenic rolling and heat treatment on mechanical properties and electrical conductivity of Cu-Ni-Si alloy with continuous directional solidification10.1016/j.jallcom.2023.169748 ↗
51. The effect of cold rolling on age hardening of Cu-3Ti-3Ni-0.5Si alloy10.1016/j.jallcom.2019.05.091 ↗
52. Microstructure and precipitate evolution in Cu-3.2Ni-0.75Si alloy processed by twin-roll strip casting10.1007/s11665-020-05371-y ↗
53. Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach10.1016/j.pnsc.2017.06.006 ↗
54. Effect of cold rolling reduction rate on mechanical properties and electrical conductivity of Cu-Ni-Si alloy prepared by temperature controlled mold continuous casting10.1016/j.msea.2019.138068 ↗
55. Structure and strength of the age hardened Cu-Ni-Si alloy10.1016/S0254-0584(02)00451-0 ↗
56. Effects of small addition of Ti on strength and microstructure of a Cu-Ni-Si alloy10.1007/s11661-015-2870-z ↗
57. An examination of microstructural evolution in a Cu-Ni-Si alloy processed by HPT and ECAP10.1016/j.msea.2013.04.004 ↗
58. Microstructure and properties of a high-strength Cu-Ni-Si-Co-Zr alloy10.1007/s11665-013-0482-6 ↗
59. Effect of G-phase and heterogeneous deformation-induced strengthening on the mechanical properties of Cu-20Ni-20Mn-2Fe-1Si alloy10.1016/j.matchar.2023.113325 ↗
60. Effects of Cr and Zr additions on microstructure and properties of Cu-Ni-Si alloys10.1016/j.msea.2016.07.021 ↗
61. The influence of Zr, P additions on microstructure and ductility of Cu-Ni-Si forged alloys10.2320/jinstmet.J2013031 ↗