journal article·2024-11Open access

Effect of pulse frequency on the microstructure and properties of laser cladding layer of AlCoCrFeNiMo high entropy alloy

Wei Zhao, Xiang Li, Jinpeng Bi, Shuai Li, Chuanxin Fang, Hui Zhang, Song Gao, Yuexia Lv, Guangchun Xiao

Abstract

The cladding layer of high entropy alloy (HEA), specifically AlCoCrFeNiMo, was fabricated using both continuous wave (CW) and pulse wave (PW) laser techniques, with pulse frequencies set at 0.5 Hz, 5 Hz, 50 Hz, 500 Hz, and 5000 Hz. The microstructure of the cladding layer was analyzed using X-ray diffraction, ultra-depth-of-field metallographic microscopy, and scanning electron microscopy. The wear resistance, corrosion resistance, and combined corrosion-wear resistance of the cladding layer were assessed using friction and wear tests, electrochemical corrosion tests, and corrosion-wear experiments. Additionally, the impact of pulse frequency on the microstructure and properties of HEA cladding layers was examined and compared with CW cladding layers. The research results indicate the presence of body-centered cubic (BCC), σ, and B2 phases in all cladding layers. Compared to the CW cladding layer, the PW cladding layer exhibits smaller grain sizes and a reduced proportion of the σ phase. With an increase in pulse frequency, there is a gradual increase in the proportion of the σ phase and a corresponding evolution in the grain sizes within the HEA cladding structure. Notably, at a specific pulse frequency of 50 Hz, the grain size reaches its minimum. PW cladding exhibited superior wear resistance, corrosion resistance, and corrosion-wear resistance compared to CW cladding, primarily due to the finer grain size observed in the former. The optimal performance of the cladding layer can be achieved when the pulse frequency was set at 50 Hz. The refinement of grain size, combined with an appropriate presence of the σ phase, synergistically contributes to enhancing cutting resistance during friction processes. This collaborative effect further hinders plastic deformation, consequently improving the wear resistance of HEA cladding. Furthermore, the grain refinement in PW cladding promotes the development of surface oxide films, which play a crucial role in reducing galvanic corrosion of alloying elements and minimizing oxygen atom diffusion rates during corrosion processes. Consequently, both corrosion resistance and corrosion wear resistance of PW cladding are significantly enhanced.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High Entropy Alloys Studies · Additive Manufacturing Materials and Processes · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Mechanical properties of Q235-Q460 mild steels at low temperatures10.1016/j.conbuildmat.2022.129850 ↗
2. Advanced high-entropy alloys breaking the property limits of current materials10.1016/j.jmst.2023.12.006 ↗
3. Wear resistance of FeCoCrNiMnAlx high-entropy alloy cladding layer at high temperature10.1016/j.apsusc.2020.145736 ↗
4. Nano-coupled heterstructure induced excellent mechanical and tribological properties in AlCoCrFeNi high alloy10.1016/j.triboint.2020.106662 ↗
5. Microstructure and mechanical properties of AlCoCrFeMnNi HEAs fabricated by selective laser melting10.1016/j.jmrt.2023.07.124 ↗
6. Synergistic effects of Mo and in-situ TiC on the microstructure and wear resistance of AlCoCrFeNi high entropy alloy fabricated by laser cladding10.1016/j.triboint.2023.108827 ↗
7. Investigation into reciprocating dry sliding frection and wear properties of bulk CoCrFeNiMo high entropy alloys fabricated by spark plasma sintering and subsequent cold rolling processes: role of Mo element concentration
8. Microstructure and properties of CoCrFeNiAlxMo2-x high-entropy alloy coating by laser cladding10.1016/j.intermet.2023.108169 ↗
9. Effect of pulse frequency on microstructure and properties of welded joints for dual phase steel by pulsed laser welding10.1016/j.matdes.2016.05.071 ↗
10. Optimizing the pulse wave mode low power fibre laser welding parameters of 22Mnb5 boron steel using response surface methodology10.1016/j.measurement.2018.10.035 ↗
11. Microstructure development in pulsed laser welding of dual phase steel to aluminium alloy10.1016/j.promfg.2018.07.058 ↗
12. Current research and development status of dissimilar materials laser welding of titanium and its alloys10.1016/j.optlastec.2020.106090 ↗
13. K. Xiang, L.Y. Chen, L.J. Chai, et al. Microstructural characteristics and properties of CoCrFeNiNbx high-entropy ally cladding layer on pure titanium substrate by pulsed laser cladding. Appl Surf Sci, 517(2020): 146214.10.1016/j.apsusc.2020.146214 ↗
14. Microstructure, hardness and wear performance of quaternary CrNbTiZr refractory medium-entropy alloy coating fabricated on a commercial Zr alloy by pulsed laser cladding10.1016/j.jmrt.2023.05.142 ↗
15. Pulsed laser cladding on IN718 alloy using pre-coated CrCoNi-TiC/SiC powders for enhancing wear resistance10.1016/j.surfcoat.2023.130253 ↗
16. Single-crystal laser deposition of super alloys: processing-microstructure maps10.1016/S1359-6454(00)00367-0 ↗
17. Synergistic and competitive mechanisms of plastic anisotropy in high-efficiency laser melting deposited TC11 alloy10.1016/j.msea.2023.145067 ↗
18. Synthesis and microstructure characterization of Ni-Cr-Co-Ti-V-Al high entropy alloy coating on Ti-6Al-4V substrate by laser surface alloying10.1016/j.matchar.2016.09.011 ↗
19. Improving mechanical properties of quasi-continuous-wave laser beam welded 7075 aluminum alloy through microstructural refinement and homogenization of the fusion zone10.1016/j.optlastec.2022.108221 ↗
20. Effects of pulse frequency on the microstructure and properties of AlCoCrFeNiMo(TiC) high-entropy alloy cladding layer prepared by laser cladding10.1016/j.surfcoat.2023.129352 ↗
21. Microstructure and corrosion behavior of CeO2/FeCoNiCrMo high-entropy alloy coating prepared by laser cladding10.1016/j.jallcom.2021.161826 ↗
22. Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition10.1016/j.jmatprotec.2016.09.005 ↗
23. Study on surface quality, precision and mechanical properties of 3D printed ZrO2 ceramic components by laser scanning stereolithography10.1016/j.ceramint.2017.09.007 ↗
24. Strengthening in Al-, Mo- or Ti-doped CoCrFeNi high entropy alloys: a parallel comparison10.1016/j.jmst.2021.02.060 ↗
25. Effect of synergistic variation in Ti and Zr elements on the microstructure and properties of laser cladding AlCoCrFeNi high-entropy alloy cladding layer10.1016/j.matchar.2023.113300 ↗
26. Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying10.1016/j.surfcoat.2024.131421 ↗
27. Microstructure and properties of W0.5Ta0.3MoNbVAlTi1-xZrx high entropy alloy cladding layer by laser cladding on the surface of 45# steel10.1016/j.ceramint.2023.08.325 ↗
28. Tribological and electrochemical behaviors of FeCoNiCrMox HEA coatings prepared by internal laser cladding on 316L steel tube10.1016/j.matchar.2024.113906 ↗
29. Al and Mo synerhancement of CoCrFeNi high-entropy alloy laser cladding layer10.1016/j.jmrt.2023.12.212 ↗
30. A combinatorial assessment of microstructure and mechanical properties in AlCrCuFeNi2Vx concentrated alloys
31. Tribological performance of a TiZrNbMo0.6 refractory high entropy alloy at elevated temperatures
32. Mechanical and tribological performance of AlCr0.5NbTaxTi4–x (x = 0, 0.5, 1) refractory high-entropy alloys10.1016/j.jmst.2023.02.016 ↗
33. Contact and rubbing of flat surfaces10.1063/1.1721448 ↗
34. Wear behavior of 7075-aluminum after ultrasonic-assisted surface burnishing10.1016/j.jmapro.2020.01.026 ↗
35. Manufacturing of FeCoCrNiCux medium-entropy alloy coating using laser cladding technology10.1016/j.matdes.2017.07.045 ↗
36. Investigation of microstructure and wear resistance of laser-clad CoCrNiTi and CrFeNiTi mediumentropy alloy cladding layer on Ti sheet10.1016/j.optlastec.2021.107518 ↗
37. Investigation into reciprocating dry sliding friction and wear properties of bulk CoCrFeNiMo high entropy alloys fabricated by spark plasma sintering and subsequent cold rolling processes: role of Mo element concentration
38. Effect of Mo element on the mechanical properties and tribological responses of CoCrFeNiMox high-entropy alloys10.3390/met11030486 ↗
39. Improving mechanical properties and tribological performance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloys via doping Si10.1016/j.jallcom.2021.159122 ↗
40. An investigation on the wear resistance and mechanism of Fe60-xCo20MoxNi20 (x=10, 15, 20) high-entropy alloy reinforced by μ-phase
41. Synergistic improvement of wear and corrosion resistance of CoCrNiMoCB cladding layer obtained by laser cladding: role of Mo concentration10.1016/j.matdes.2022.110751 ↗
42. Y.S. Effects of ultrasonic impact treatment on the corrosion resistance of laser-cladded CrMnFeCoNi high-entropy alloy coatings10.1016/j.surfcoat.2024.131102 ↗
43. Electrochemical behaviour of passive film formed on the surface of Ti-6Al-4V alloys fabricated by electron beam melting10.1016/j.corsci.2018.09.010 ↗
44. Materials for extreme environments10.1038/s41578-022-00496-z ↗
45. Investigation on the relationship between reinforcing behavior of TiN and wear resistance of AlCoCrCuNiTi high-entropy alloy coating10.1016/j.apsusc.2022.153419 ↗
46. Corrosion and corrosive wear of AlCrFeCoNi and Co–free AlCrFeNi-Tix (x=0-1.5) high–entropy alloys in 3.5 wt% NaCl and H2SO4 (pH=3) solutions10.1016/j.wear.2023.204765 ↗
47. Corrosion behavior and mechanism of dual phase Fe1.125Ni1.06CrAl high entropy alloy10.1016/j.corsci.2022.110276 ↗
48. Microstructure and corrosion behavior of CeO2/FeCoNiCrMo high-entropy alloy coating prepared by laser cladding10.1016/j.jallcom.2021.161826 ↗