journal article·2023-07Open access

Preparation of high performance Ti–6Al–4V alloy thin strip by on-line warm rolling and study of its microstructure evolution and mechanical properties

Qiang-qiang Zhu, Su Huang, Wen-yong Niu, Hui-fang Lan, Tao Sun, Gui-Qiao Wang, Xing-di Yang, Jian-ping Li

Abstract

To address the challenges associated with preparing thin strips of difficult-to-deform materials – such as low processing efficiency and yield, poor shape, and subpar performance – our research team developed an on-line warm rolling experimental machine featuring hydraulic tension. We used the Ti-6Al-4V alloy as our experimental material and conducted warm rolling experiments at various temperatures, thoroughly examining the intricate relationship between microstructure evolution and mechanical properties. Our findings indicate that warm rolling causes a clear refinement of the α phase and β phase microstructures, while intensifying dislocation entanglement. These changes significantly enhance the strength of the Ti-6Al-4V alloy, though Total Elongation Limit (TEL) decreases. After evaluating mechanical properties, surface quality, and energy consumption associated with warm rolling, we determined the optimal warm rolling temperature for the Ti-6Al-4V alloy to be 650°C. At this temperature, the Ultimate Tensile Strength (UTS), Yield Strength (YS), and TEL were 1325MPa, 1164MPa, and 8.0%, respectively, maintaining good ductility. The impressive performance of the Ti-6Al-4V alloy sheet is mainly attributed to the strengthening effects of fine grain and dislocation, while the introduction of some fine recrystallization enhances ductility. High-performance Ti-6Al-4V alloy thin strip was successfully prepared by on-line warm rolling with hydraulic tension, which provided a new idea for the preparation of thin strip of difficult-to-deform materials.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Additive Manufacturing Materials and Processes · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Optimization of blended-elemental powderbased titanium alloy extrusions for aerospace applications10.1007/s11661-012-1437-5 ↗
2. Perspectives on titanium science and technology10.1016/j.actamat.2012.10.043 ↗
3. Developement and mechanical properties of Ti-15-3 alloy for aerospace applicaitons
4. Improved ductility and oxidation resistance of cast Ti-6Al-4V alloys by microalloying10.1016/j.jallcom.2014.03.039 ↗
5. A study of the microstructure and hardness of two titanium alloys: commercially pure and Ti-6Al-4V10.1016/j.jallcom.2009.06.172 ↗
6. Hot deformation behavior of Ti-6Al-4V alloy: effect of initial microstructure10.1016/j.jallcom.2017.05.097 ↗
7. Microstructure-fracture toughness correlation in an aircraft structural component alloy Ti-5Al-5V-5Mo- 3Cr10.1016/j.msea.2013.01.017 ↗
8. Research and application of high strength and high toughness titanium alloys
9. Constitutive modeling and the effects of strain-rate and temperature on the formability of Ti-6Al-4V alloy sheet10.1016/j.matdes.2013.09.069 ↗
10. Research status in preparation and properties of ultra-fine grained Ti alloys
11. Producing bulk ultrafinegrained materials by severe plastic deformation
12. ARB (accumulative roll-bonding) and other new techniques to produce bulk ultrafine grained materials10.1002/adem.200310077 ↗
13. An alternative method for manufacturing high- strength CP Ti-SiC composites by accumulative roll bonding process10.1016/j.matdes.2014.03.040 ↗
14. Ti-6Al-4V alloy with an ultrafine-grained microstructure exhibiting low-temperature-highstrain-rate superplasticity10.1016/j.matlet.2013.02.033 ↗
15. Effects of equal-channel angular pressing and accumulative roll-bonding on hydrogen storage properties of a commercial ZK60 magnesium alloy10.1016/j.ijhydene.2015.05.149 ↗
16. Solid-state alloying of Al-Mg alloys by accumulative roll-bonding: microstructure and properties10.1016/j.jmst.2022.02.029 ↗
17. Microstructure and mechanical properties of commercial purity titanium severely deformed by ARB process10.1007/s10853-006-0909-7 ↗
18. Microstructural evolution during accumulative roll-bonding of commercial purity aluminum10.1016/S0921-5093(02)00182-X ↗
19. Flow softening mechansim of a Ti alloy with lamellar structure during subtransus deformation
20. Effect of electroplastic rolling on deformability, mechanical property and microstructure evolution of Ti-6Al-4V alloy strip10.1016/j.matchar.2014.10.026 ↗
21. Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition10.1016/j.actamat.2014.11.028 ↗
22. Effect of cold rolling and subsequent annealing on grain refinement of a beta titanium alloy showing stress-induced martensitic transformation10.1016/j.msea.2018.06.050 ↗
23. Effects of cold and warm cross-rolling on microstructure and texture evolution of AZ31B magnesium alloy sheet
24. Effect of rolling reduction on microstructure, texture, mechanical properties and mechanical anisotropy of AZ31 magnesium alloys10.1016/j.msea.2014.06.034 ↗
25. Microstructure-texture-mechanical properties relationship in multi-pass warm rolled Ti-6Al-4V alloy10.1016/j.msea.2013.09.087 ↗
26. Effect of two phase warm rolling on aging behavior and mechanical properties of Ti-15Mo-5Zr-3Al alloy10.1016/S0921-5093(97)00791-0 ↗
27. Enhanced mechanical response of an ultrafine grained Ti-6Al-4V alloy produced through warm symmetric and asymmetric rolling
28. Study on symmetry and asymmetry rolling of AA2519-T62 alloy at room-temperature and cryogenic conditions10.3390/ma15217712 ↗
29. Microstructure and mechanical properties of Ti-6Al-4V alloy sheets via room-temperature rolling and cryorolling10.1016/j.msea.2022.142600 ↗
30. Factors determining room temperature mechanical properties of bimodal microstructures in Ti-6Al-4V alloy10.1016/j.msea.2018.06.019 ↗
31. High-performance magnesium alloy with multi-element synergistic strengthening: design, microstructure, and tensile properties10.1016/j.jallcom.2022.165746 ↗
32. Effects of dynamic recrystallization mechanisms on texture evolution in Mg-Gd-Y-Zr-Ag alloy during hot compression10.1016/j.jallcom.2023.169190 ↗
33. High strength and toughness of Ti-6Al-4V sheets via cryorolling and short-period annealing10.1016/j.msea.2022.143766 ↗
34. Edge crack damage analysis of AZ31 magnesium alloy hot-rolled plate improved by vertical roll pre-rolling
35. Microstructural evolution of twin-roll cast Mg-3Al-0.5Mn-0.2Mm alloys during warm rolling and subsequent annealing10.1016/j.jmatprotec.2010.03.013 ↗
36. Structure, texture and strength of Mg-5.8Zn-0.65Zr alloy after hot-to-warm multi-step isothermal forging and isothermal rolling to large strains10.1016/j.msea.2017.10.008 ↗
37. Ultra-grain refinement and enhanced low-temperature superplasticity in a friction stir-processed Ti-6Al-4V alloy10.1016/j.msea.2018.03.009 ↗
38. The optimal temperature for enhanced low-temperature superplasticity in fine-grained Ti-15V-3Cr-3Sn-3Al alloy fabricated by friction stir processing
39. Grain refinement and superplastic flow in friction stir processed Ti-15V-3Cr-3Sn-3Al alloy
40. A constitutive model to describe high temperature flow behavior of AZ31B magnesium alloy processed by equal-channel angular pressing10.1016/j.msea.2019.03.106 ↗
41. Deformation mechanisms in h.c.p. metals at elevated temperatures-II. Creep behavior of a Mg-0.8% Al solid solution alloy
42. Grain refinement and superplastic flow in a fully lamellar Ti-6Al-4V alloy processed by high-pressure torsion10.1016/j.msea.2018.07.010 ↗
43. Ultra-grain refinement and enhanced low-temperature super-plasticity in a friction stir-processed Ti-6Al-4V alloy10.1016/j.msea.2018.03.009 ↗
44. Microstructure evolution and mechanical behavior of ultrafine Ti-6Al-4V during low-temperature superplastic deformation10.1016/j.actamat.2016.09.003 ↗
45. Superplastic forming at high strain rates after severe plastic deformation10.1016/S1359-6454(00)00182-8 ↗
46. Experimental evidence for grain-boundary sliding in ultrafine-grained aluminum processed by severe plastic deformation10.1002/adma.200501232 ↗
47. Yield strength-ductility trade-off breakthrough in Co-free Fe40Mn10Cr25Ni25 high-entropy alloys with partial recrystallization
48. Reduced yield asymmetry and excellent strength-ductility synergy in Mg-Y-Sm-Zn-Zr alloy via ultra-grain refinement using simple hot extrusion
49. Heterogeneous structure-induced strength-ductility synergy by partial recrystallization during friction stir welding of a high-entropy alloy10.1016/j.matdes.2020.109238 ↗
50. Interface microstructure and bonding mechanisms of 7050 aluminum alloy thick plates produced by vacuum roll cladding10.1016/j.msea.2022.143582 ↗
51. Metadynamic recrystallization behavior of 5083 aluminum alloy under double-pass compression and stress relaxation tests10.1016/j.msea.2021.141673 ↗
52. Study on the hot deformation behavior of a novel multi-element synergistic strengthening Mg-Al-Ca-Mn-Zn-Sn alloy10.1016/j.jallcom.2023.170156 ↗
53. Kinetic model for describing continuous and discontinuous dynamic recrystallization behaviors of 2195 aluminum alloy during hot deformation10.1016/j.matchar.2021.111492 ↗
54. Effect of subgrain and the associated DRX behaviour on the texture modification of Mg-6.63Zn-0.56Zr alloy during hot tensile deformation10.1016/j.msea.2021.141745 ↗
55. Mechanistic investigation on Ce addition in tuning recrystallization behavior and mechanical property of Mg alloy10.1016/j.jmst.2022.05.042 ↗