Investigation the effects of friction stir processing on microstructure and mechanical properties of Al–Cu alloy fabricated by wire arc additive manufacturing
Source abstract
Abstract
In this study, a hybrid additive manufacturing (AM) process that combines interlayer friction stir processing (FSP) with wire arc additive manufacturing (WAAM) is proposed to address the problems of high porosity, coarse grains, and low mechanical properties encountered in WAAM Al alloys. Straight walls of Al–Cu alloy were prepared using Er2319 wire and interlayer FSP was conducted to tailor the microstructure of deposited layers. The effects of interlayer FSP on the microstructure and mechanical properties of WAAM Al–Cu alloy was analyzed. Results show that the pore characteristics vary at different regions on the cross-section of the deposited walls. The interlayer FSP can partially repair pores by violent stirring action and downward force from FSP tool, and thereby decreases the pore size, pore density and pore area fraction of the WAAM Al–Cu alloy. Additionally, the interlayer FSP can significantly refine grains, resulting in a wider fine grain region in the WAAM-FSP sample. The WAAM-FSP samples have a larger number density of spot-like particles as compared to the WAAM samples due to the fragmentation as well as partially dissolution of second-phase particles caused by the violent stirring action and intense deformation of FSP. Both strengths and elongations of the manufactured Al–Cu alloy are enhanced by interlayer FSP, which is mainly ascribed to the combined action of porosity reduction, grain refinement, fragmentation and dissolution of the second-phase particles caused by interlayer FSP. The present study can provide theoretical guidance for the fabrication of Al-based alloy components with high performance using hybrid WAAM-FSP technique.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium10.1080/02670836.2018.1455012 ↗
2. A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement10.1016/j.jmapro.2018.08.001 ↗
3. Effect of wire and arc additive manufacturing (WAAM) process parameters on bead geometry and microstructure
4. Additive manufacturing method and different welding applications10.1016/j.jmrt.2020.08.039 ↗
5. Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy10.1007/s00170-014-6346-x ↗
6. Influence of arc mode on the microstructure and mechanical properties of 5356 aluminum alloy fabricated by wire arc additive manufacturing10.1016/j.jmrt.2022.08.005 ↗
7. Review on effect of heat input for wire arc additive manufacturing process10.1016/j.jmrt.2021.02.002 ↗
8. Integrated approach to wire arc additive manufacturing (WAAM) optimization: harnessing the synergy of process parameters and deposition strategies10.1016/j.jmrt.2024.03.170 ↗
9. Wire arc additive manufacturing of Al-6Mg alloy using variable polarity cold metal transfer arc as power source10.1016/j.msea.2017.11.084 ↗
10. Microstructure and mechanical properties of double-wire + arc additively manufactured Al-Cu-Mg alloys10.1016/j.jmatprotec.2017.12.019 ↗
11. Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening10.1016/j.jallcom.2018.02.353 ↗
12. Improving mechanical properties of austenitic stainless steel by the grain refinement in wire and arc additive manufacturing assisted with ultrasonic impact treatment10.1016/j.msea.2022.144044 ↗
13. Integration of deformation processing with additive manufacture of Ti-6Al-4V components for improved β grain structure and texture
14. Effects of ultrasonic peening treatment in three directions on grain refinement and anisotropy of cold metal transfer additive manufactured Ti-6Al-4V thin wall structure10.1016/j.jmapro.2020.03.010 ↗
15. The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys10.1016/j.jmatprotec.2015.11.006 ↗
16. Application of bulk deformation methods for microstructural and material property improvement and residual stress and distortion control in additively manufactured components10.1016/j.scriptamat.2016.10.031 ↗
17. Control of residual stress and distortion in aluminium wire + arc additive manufacture with rolling
18. Experimental study on surface characteristics of laser cladding layer regulated by high-frequency microforging10.1007/s11666-010-9534-8 ↗
19. Microstructure and mechanical properties of wire + arc additively manufactured mild steel by welding with trailing hammer peening10.1002/srin.202100238 ↗
20. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
21. Mechanical and microstructural characterization of aluminium powder deposit made by friction stir based additive manufacturing10.1016/j.jmatprotec.2020.116648 ↗
22. Effect of inter-layer rotary friction processing on porosity of arc-directed energy-deposited high-strength aluminum alloys10.1016/j.jmatprotec.2023.117951 ↗
23. Achieving high performance of wire arc additive manufactured Mg-Y-Nd alloy assisted by interlayer friction stir processing10.1016/j.jmatprotec.2022.117809 ↗
24. Ductilization of selective laser melted Ti6Al4V alloy by friction stir processing10.1016/j.msea.2019.03.133 ↗
25. Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing10.1016/j.jmrt.2023.06.053 ↗
26. Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing10.1016/j.jmst.2022.07.001 ↗
27. Formation mechanism of porosity in laser welding-brazing of Ti/Al dissimilar alloys
28. Microstructural and defect evolution during WAAM resulting in mechanical property differences for AA5356 component10.1016/j.jmrt.2022.11.116 ↗
29. Alloy composition and metal/mold heat transfer efficiency affecting inverse segregation and porosity of as-cast Al-Cu alloys10.1016/j.matdes.2008.08.032 ↗
30. Microstructures and mechanical properties of Al-Zn-Mg aluminium alloy samples produced by wire + arc additive manufacturing10.1016/j.jmrt.2020.09.114 ↗
31. Pore formation and evolution in wire + arc additively manufactured 2319 Al alloy
32. Keyhole fluctuation and pore formation mechanisms during laser powder bed fusion additive manufacturing10.1038/s41467-022-28694-x ↗
33. The interaction of hydrogen and dislocations in iron10.1016/0001-6160(69)90097-2 ↗
34. Hydrogen-modified interaction between lattice dislocations and grain boundaries by atomistic modelling10.1016/j.ijhydene.2020.01.103 ↗
35. Four-dimensional annihilation behaviors of micro pores during surface cold working10.2320/matertrans.M2010069 ↗
36. Solids Co. Ostwald ripening in porous materials: the case of arbitrary Pore size distributions10.1016/0022-3697(95)00021-6 ↗
37. Investigation of microstructure and properties in an aged ultra-high strength Al alloy and its friction stir welded joints10.1016/j.jmrt.2022.10.067 ↗
38. A framework for shear driven dissolution of thermally stable particles during friction stir welding and processing10.1016/j.msea.2016.10.015 ↗
39. Preparation and characterization of CMT wire arc additive manufacturing Al-5% Mg alloy depositions through assisted longitudinal magnetic field10.1016/j.jmapro.2023.05.104 ↗
40. Modelling grain boundary strengthening in ultra-fine grained aluminum alloys10.1016/j.msea.2005.08.121 ↗