journal article·2025-09Open access

A new hybrid surface strengthening method for 42CrMo steel based on ultrasonic shot peening and low-temperature nitriding

Zhi Chen, Lexing Deng, Zouhao Song, Xiaoyan Wu, Guojun Zhang, Fenglin Han

Abstract

42CrMo steel, a high-strength chromium–molybdenum alloy steel, is widely used in the manufacture of high-end key parts that must withstand high loads and stresses over extended service times. Under extreme service conditions, such as high speed, heavy loading, and frequent impact, the failure of 42CrMo steel components typically initiates at the surface and then extends inward. Single shot peening treatment can refine grains and introduce high compressive residual stress, but the improvement of surface hardness is limited. Conversely, nitriding treatment alone markedly increases surface hardness, but it is usually accompanied by surface cracking and grain coarsening. In this study, seven types of surface treatment processes were applied to 42CrMo steel, single shot peening (S-SP), single high-temperature nitriding (S-HT), single low-temperature nitriding (S-LT), shot peening followed by high-temperature nitriding (S-SP + HT), high-temperature nitriding followed by shot peening (S-HT + SP), shot peening followed by low-temperature nitriding (S-SP + LT), and low-temperature nitriding followed by shot peening (S-LT + SP). Untreated samples were designated as S-UT. The surface properties after the different treatments, including morphology, microstructural features, mechanical properties, and tribological performance, were systematically compared and analyzed. The results show that the greatest nitriding-layer depth (121 μm, an increase of 31.0 % and 9.1 % compared with S-LT and S-HT, respectively) is obtained under the method combining shot peening pretreatment and low-temperature nitriding (S-SP + HT), as accompanied by the highest compressive residual stress (−1024.5 MPa, an increase of 22.6 % and 72.4 % compared with S-SP and S-LT, respectively) and the lowest wear rate (1.7 mm 3 /N·m, a decrease of 91.8 %, 45.2 %, and 55.3 % compared with S-UT, S-LT, and S-HT, respectively). This is because the dislocations and other crystallographic defects introduced by the shot peening pretreatment facilitate the penetration and diffusion of nitrogen ions into the steel and promote the formation of nitrides. Moreover, compared with S-SP + HT, S-SP + LT effectively inhibits the recovery of dislocation defects and grain-size coarsening at elevated temperatures. This work thus provides a theoretical basis and practical process guidance for the surface strengthening of 42CrMo steel under extreme service conditions.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Surface Treatment and Residual Stress · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (79)

Show source-provided references
1. Experimental study on the wear properties of 42CrMo steel with different microstructures and T15 laser cladding10.1007/s11665-021-06495-5 ↗
2. Wear and rolling contact fatigue competition mechanism of different types of rail steels under various slip ratios10.1016/j.wear.2023.204721 ↗
3. Evaluation of mechanical properties of different casing drilling steels10.3390/met13020427 ↗
4. Fretting fatigue of 42CrMo4+ QT steel: experimental and numerical assessment10.1016/j.ijfatigue.2024.108575 ↗
5. Roles of microstructures in high-cycle fatigue behaviors of 42CrMo high-strength steel under near-yield mean stress10.1016/j.ijfatigue.2023.107928 ↗
6. Probabilistic fatigue life prediction of an aero-engine turbine shaft10.1108/AEAT-08-2021-0232 ↗
7. Application of life cycle of aeroengine mainshaft bearing based on digital twin10.3390/pr11061768 ↗
8. Rolling bearing fault diagnosis based on wavelet overlapping group shrinkage and extended envelope hierarchical multiscale-weighted permutation entropy10.3390/machines13040278 ↗
9. Tribological characteristics and advanced processing methods of textured surfaces: a review10.1007/s00170-021-06954-2 ↗
10. On coating techniques for surface protection: a review10.3390/jmmp3010028 ↗
11. Insight into the corrosion behaviors and mechanism of arc discharge plasma nitrided H13 steel in molten Al-Si10.1016/j.apsusc.2024.160584 ↗
12. Investigation of surface modifications for combating the molten aluminum corrosion of AISI H13 steel10.1016/j.corsci.2020.108836 ↗
13. Influence of cryogenic treatment on the corrosion properties of 42CrMo low alloy steel10.3390/ma16030899 ↗
14. Research status of the influence of machining processes and surface modification technology on the surface integrity of bearing steel materials10.1007/s00170-023-10960-x ↗
15. Improvement in mechanical properties of 42CrMo4 steel through novel thermomechanical processing treatment10.1007/s13632-020-00684-9 ↗
16. Plasma immersion ion implantation of a Fe-Mn-C based steel for biomedical applications: effect of gases and treatment times on the surface properties10.4028/p-iY6e3n ↗
17. Influence of plasma nitriding on surface layer of M50NiL steel for bearing applications10.1515/jmbm-2024-0022 ↗
18. Mechanical and wear properties of 42CrMo steel by plasma nitriding assisted hollow cathode ion source10.1590/1980-5373-mr-2021-0137 ↗
19. Effects of carburizing and nitriding sequential treatment on rolling contact fatigue of M50NiL bearing steel10.1007/s10853-024-09905-w ↗
20. The effect of ultrasonic shot peening on the fatigue life of alloy materials: a review
21. Effects of surface integrity on wear resistance of 42CrMo steel subjected to ultrasonic shot peening10.1016/j.jmapro.2025.06.013 ↗
22. Thermal stability of residual stress, microstructure, and mechanical property in shot-peened CNT/Al-Cu-Mg composites10.3390/coatings14121571 ↗
23. The effect of shot peening time on mechanical properties and residual stress in Ti-6Al-4V alloy10.1051/metal/2022036 ↗
24. The influence of shot peening on mechanical properties, wear, and corrosion resistance of 42CrMo steel10.1007/s00170-024-13052-6 ↗
25. Guangrui X, Xiang G, Xia L, et al. Insight into the ablation behaviors and mechanism of duplex surface treated Tc11 titanium alloy via dynamic shot peening and plasma nitriding. Available at: SSRN 4797794.
26. Insight into the ablation behaviors and mechanism of duplex surface treated TC11 titanium alloy via dynamic shot peening and plasma nitriding10.1016/j.matchar.2025.114887 ↗
27. Shot peening pre-treatment for nano-nitriding layer formation to enhance wear and corrosion resistance in medical titanium alloys10.1016/j.matlet.2024.136669 ↗
28. The influence of hot deformation on the mechanical and structural properties of 42CrMo4 steel10.3390/met14060647 ↗
29. Nitriding effect on the tribological performance of CrN-, AlTiN-, and CrN/AlTiN-coated DIN 1.2367 hot work tool steel10.3390/ma16072804 ↗
30. The influence of ultrasonic shot peening on the microstructure and fatigue behavior of TC17 alloy
31. Softening mechanisms and microstructure evolution of 42CrMo steel during hot compressive deformation10.1016/j.jmrt.2023.02.141 ↗
32. Low-temperature plasma nitriding of 3Cr13 steel accelerated by rare-earth block10.3390/coatings11091050 ↗
33. Printability of low-cost pre-heat-treated ball milled Al7075 powders using compressed air assisted cold spray additive manufacturing10.1016/j.addlet.2022.100046 ↗
34. 2000
35. Surface hardening behavior of advanced gear steel C61 by a novel solid-solution carburizing process10.3390/met12030379 ↗
36. Glancing angle intermediate layer deposition approach for CVD diamond coating of high-speed steel substrates
37. Tribological behavior of gas-nitrided 42CrMo4 steel at elevated temperatures10.3390/coatings15010018 ↗
38. Influence of gas pressure on the low-temperature plasma nitriding of surface-na nocrystallined TC4 titanium alloy10.1016/j.surfcoat.2022.128327 ↗
39. Effect of the pre-shot peening and nitrogen ion implantation combined surface treatments on the surface structure and properties of gear steel 16Cr3NiWMoVNbE10.3390/met12091509 ↗
40. Surface nanocrystallization and numerical modeling of 316L stainless steel during ultrasonic shot peening process10.3390/met12101673 ↗
41. Microstructure and properties of the compound layer obtained by pulsed plasma nitriding in steel gears10.1016/j.surfcoat.2008.11.025 ↗
42. Effect of plasma oxynitriding temperature on wear and corrosion resistance of the AISI 4140 steel10.1111/ijac.14128 ↗
43. Formation mechanisms and crack propagation behaviors of white etching layers and brown etching layers on raceways of failure bearings10.3390/lubricants12020059 ↗
44. Synergetic effects of micro-shot peening and gas nitriding on the fatigue performance of AISI 4140 steel10.1016/j.surfcoat.2024.130856 ↗
45. Mechanical and microstructural characteri zation of AISI 316L stainless steel superficially modified by solid nitriding technique10.3390/coatings14091167 ↗
46. The effect of the transformation of ε-Fe2-3N into γ′-Fe4N phase on the fatigue strength of gas-nitrided pure iron10.3390/met10060823 ↗
47. Surface modification of 42CrMo steels: a review from wear and corrosion resistance10.3390/coatings14030337 ↗
48. The influence of plasma nitriding on the resistance of X20Cr13 steel to cavitation erosion10.1016/j.wear.2025.205757 ↗
49. Prediction of the effect of shot peening residual stress on fretting fatigue behaviour10.1016/j.ijfatigue.2023.107909 ↗
50. Improving stress corrosion resistance and wear resistance of austenitic hot-stamping die steels via synergistic effects of shot peening and plasma nitriding10.1016/j.surfcoat.2024.130448 ↗
51. Investigation of microstructure, residual stress, and hardness of Ti-6Al-4V after plasma nitriding process with different times and temperatures10.3390/coatings12121932 ↗
52. Effect of shot peening and nitriding on toughness and abrasive wear resistance of powder metallurgic steels highly alloyed with vanadium10.3390/met14010022 ↗
53. Thin modified nitrided layers of high-speed steels10.3390/ma18112434 ↗
54. Study of the effect of gas nitriding time on microstructure and wear resistance of 42CrMo4 steel
55. Theoretical study of the crystal structure, stability, and properties of phases in the VN system10.1103/PhysRevB.104.134111 ↗
56. Nanoengineering steel's durability: creating gradient nanostructured spheroidal carbides and lath-shaped nano-martensite via ultrasonic shot peening10.1039/D4NR02994A ↗
57. Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite10.1016/j.matdes.2021.109760 ↗
58. Interplay between alloying and tramp element effects on temper embrittlement in bcc iron: DFT and thermodynamic insights10.1016/j.actamat.2024.120044 ↗
59. Microstructure and fracture toughness of nitrided D2 steels using potential-controlled nitriding10.3390/met12010139 ↗
60. Evaluation of wear model equations through analysis of experimental wear data of materials from literature10.24874/ti.1555.09.23.11 ↗
61. Influences of Cu, Mn, Al, and Mo additions (X) on mechanical and tribological properties of FeCrNiCoX high-entropy coatings10.1016/j.surfcoat.2025.132428 ↗
62. Mechanical, thermal, and high-temperature tribological properties of ti–al–c reinforced NiCrAlY coatings for boiler applications10.1016/j.jmrt.2025.07.018 ↗
63. Creation and evolution of roughness on silica under unlubricated wear
64. Enhanced wear resistance of gas nitrided AISI 431 HVOF coatings at elevated temperatures10.1007/s11665-024-10501-x ↗
65. Modelling of layer development and nitrogen distribution on different microstructures during plasma nitriding10.1016/j.surfcoat.2022.128813 ↗
66. Plasma nitriding of ISO 5832-1 stainless steel with intermittent nitrogen flow at 450 C10.1590/1980-5373-mr-2019-0501 ↗
67. Ammonia decomposition enhancement by Cs-promoted Fe/Al2O3 catalysts10.1007/s10562-020-03247-3 ↗
68. The “expanded” phases in the low-temperature treated stainless steels: a review10.3390/met12020331 ↗
69. Oscillatory mechanism of α-Fe (N)↔ γ’-Fe4N phase transformations during nanocrystalline iron nitriding10.3390/ma15031006 ↗
70. Atomistic modelling of all dislocations and twins in HCP and BCC Ti
71. The Fe-N system: crystal structure prediction, phase stability, and mechanical properties10.1016/j.commatsci.2025.113739 ↗
72. A dislocation density–based comparative study of grain refinement, residual stresses, and surface roughness induced by shot peening and surface mechanical attrition treatment10.1007/s00170-020-05413-8 ↗
73. Effect of Cu alloying on mechanical properties of medium-C steel after long-time tempering at 500° C10.3390/ma16062390 ↗
74. Strength-hardness relationship for AlSi10Mg alloy produced by laser powder bed fusion: an experimental study10.1016/j.msea.2022.144345 ↗
75. Experimental measurement of dislocation density in metallic materials: a quantitative comparison between measurements techniques (XRD, R-ECCI, HR-EBSD, TEM)10.1016/j.matchar.2023.112842 ↗
76. Multiscale modelling of precipitation hardening: a review
77. Effects of V–N microalloying on microstructure and property in the welding heat affected zone of constructional steel10.3390/met12030480 ↗
78. Understanding crack growth within the γ′ Fe4N layer in a nitrided low carbon steel during monotonic and cyclic tensile testing10.1007/s10853-024-10014-x ↗
79. Numerical simulation and surface properties of 42CrMo steel treated by plasma nitriding and laser quenching10.3390/met13081473 ↗