Effects of Aging Treatment on Intergranular Corrosion and Stress Corrosion Cracking Behavior of AA7003
Source abstract
Abstract
In order to study the effects of aging treatment on the intergranular corrosion (IGC) and stress corrosion cracking (SCC) of 7003 aluminum alloy (AA7003), the intergranular corrosion test, electrochemical test and slow strain rate test (SSRT), combined with optical microscopy (OM) and scanning electron microscopy (SEM) as well as transmission electron microscopy (TEM) observations have been carried out. The IGC and electrochemical test results showed that the IGC resistance of AA7003 for peak aged (PA) temper is the lowest, with double peak aged (DPA) the moderate, and retrogression and re-aging (RRA) the highest among three tempers, which is attributed to the continuous feature of precipitation on grain boundary of PA temper and the interrupted feature of precipitation on grain boundary of DPA and RRA tempers, as well as the wide precipitation free zones (PFZ) of RRA temper. In addition, the SSRT results indicated that all three tempers AA7003 are susceptible to SCC in IGC solution, and the change tendency of SCC susceptibility (ISCC) of AA7003 for three tempers follows the order: ISCC(RRA)<ISCC(DPA)<ISCC(PA).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Hill J A, Markley T, Forsyth M. Corrosion Inhibition of 7000 Series Aluminum Alloys with Cerium Diphenyl Phosphate[J]. J. Alloy. Compd., 2011, 509(5): 1683–169010.1016/j.jallcom.2010.09.151 ↗
2. Xu D K, Birbilis N, Rometsch P A. Effect of S-Phase Dissolution on the Corrosion and Stress Corrosion Cracking of an As-Rolled Al-Zn-Mg-Cu Alloy[J]. Corrosion, 2012, 68(3): 1–10
3. Huda Z, Edi P. Materials Selection in Design of Structures and Engines of Supersonic Aircrafts[J]. Int. J. Mech. Mater. Des., 2013, 46(4): 552–560
4. Dursun T, Soutis C. Recent Developments in Advanced Aircraft Aluminium Alloys[J]. Mater. Design, 2014, 56(4): 862–87110.1016/j.matdes.2013.12.002 ↗
5. Zhang X Y, Song R G, Sun B, et al. Effects of Applied Potentionals on Stress Corrosion Cracking Behavior of 7003 Aluminum Alloy in Acid and Alkaline Chloride Solutions[J]. Int. J. Miner. Metall. Mater., 2016, 23(7): 819–82610.1007/s12613-016-1296-y ↗
6. Qi X, Song R G, Qi W J, et al. Effects of Polarisation on Mechanical Properties and Stress Corrosion Cracking Susceptibility of 7050 Aluminum Alloy[J]. Corros. Eng. Sci. Technol., 2014, 49(7): 643–65010.1179/1743278214Y.0000000162 ↗
7. Rometsch P A, Zhang Y, Knight S. Heat Treatment of 7xxx Series Aluminium Alloys-Some Recent Developments[J]. Trans. Nonferrous. Met. Soc. China, 2014, 24(7): 2003–201710.1016/S1003-6326(14)63306-9 ↗
8. Mondal DP, Jha N, Badkul A. Effect of Al-TiB Master Alloy Addition on Microstructure, Wear and Compressive Deformation Behaviour of Aluminum Alloys[J]. Trans. Nonferrous. Met. Soc. China, 2012, 22(5): 1001–101110.1016/S1003-6326(11)61276-4 ↗
9. Marlaud T, Malki B, Henon C, et al. Relationship between Alloy Composition, Microstructure and Exfoliation Corrosion in Al-Zn-Mg-Cu Alloys[J]. Corros. Sci., 2011, 53(10): 3139–314910.1016/j.corsci.2011.05.057 ↗
10. Zupanc U, Grum J. Effect of Pitting Corrosion on Fatigue Performance of Shotpeened Aluminum Alloy 7075-T651[J]. J. Mater. Process. Technol., 2010, 210(9): 1197–120210.1016/j.jmatprotec.2010.03.004 ↗
11. Rout P K, Ghosh M M, Ghosh K S. Influence of Aging Treatments on Alterations of Microstructural Features and Stress Corrosion Cracking Behavior of an Al-Zn-Mg Alloy[J]. J. Mater. Eng. Perform., 2015, 24(7): 2792–280510.1007/s11665-015-1559-1 ↗
12. Song R G, Dietzel W, Zhang B J, et al. Stress Corrosion Cracking and Hydrogen Embrittlement of an Al-Zn-Mg-Cu Alloy[J]. Acta Mater., 2004, 52(16): 4727–474310.1016/j.actamat.2004.06.023 ↗
13. Shi Y, Pan Q, Li M, et al. Influence of Alloyed Sc and Zr, and Heat Treatment on Microstructures and Stress Corrosion Cracking of Al-Zn-Mg-Cu Alloys[J]. Mater. Sci. Eng. A, 2015, 621: 173–18110.1016/j.msea.2014.10.058 ↗
14. Qi X, Song R G, Qi W J, et al. Correspondence between Susceptibility to SCC of 7050 Aluminum Alloy and Passive Film Induced Stress at Various pH Values[J]. J. Wuhan University of Technology-Mater. Sci. Ed., 2017, 32(1): 173–17810.1007/s11595-017-1576-z ↗
15. Holroyd H, Scamans G M. Sensitization, Intergranular Corrosion, and Environment-Induced Cracking of Aluminum-Magnesium Alloys[J]. Corrosion, 2016, 72(2): 135–13510.5006/0010-9312-72.2.135 ↗
16. Marlaud T, Deschamps A, Bley F, et al. Evolution of Precipitate Microstructures during the Retrogression and Re-ageing Heat Treatment of an Al-Zn-Mg-Cu alloy[J]. Acta Mater., 2010, 58(14): 4814–482610.1016/j.actamat.2010.05.017 ↗
17. Angappan M, Sampath V, Ashok B, et al. Retrogression and Reaging Treatment on Short Transverse Tensile Properties of 7010 Aluminum Alloy Extrusions[J]. Int. J. Mech. Mater. Des., 2011, 32(7): 4050–4053
18. Han N M, Zhang X M, Liu S D, et al. Effects of Pre-stretching and Ageing on the Strength and Fracture Toughness of Aluminum Alloy 7050[J]. Mater. Sci. Eng. A, 2011, 528(10-11): 3714–372110.1016/j.msea.2011.01.068 ↗
19. Xiao Y P, Pan Q L, Li W B, et al. Influence of Retrogression and Reaging Treatment on Corrosion Behavior of an Al-Zn-Mg-Cu alloy[J]. Int. J. Mech. Mater. Des., 2011, 32(4): 2149–2156
20. Wang Y L, Pan Q L, Wei L L, et al. Effect of Retrogression and Reaging Treatment on the Microstructure and Fatigue Crack Growth Behavior of 7050 Aluminum Alloy Thick Plate[J]. Int. J. Mech. Mater. Des., 2014, 55(6): 857–863
21. Zheng C B, Yan B H, Zhang K, et al. Electrochemical Investigation of Hydrogen Permeation Behavior of 7075 T6 Al Alloy and Its Implication on Stress Corrosion Cracking[J]. Int. J. Miner. Metall. Mater., 2015, 22(7): 729–73710.1007/s12613-015-1128-5 ↗
22. Qi X, Jin J R, Dai C L, et al. A Study on the Susceptibility to SCC of 7050 Aluminum Alloy by DCB Specimens[J]. Materials, 2016, 9(11): 88410.3390/ma9110884 ↗
23. Nie X W, Zhang L J, Yong D U. Experiments and Modeling of Double-peak Precipitation Hardening and Strengthening Mechanisms in Al-Zn-Mg alloy[J]. Trans. Nonferrous. Met. Soc. China, 2014, 24(7): 2138–214410.1016/S1003-6326(14)63324-0 ↗
24. Shu W X, Hou L G, Zhang C, et al. Tailored Mg and Cu Contents Affecting the Microstructures and Mechanical Properties of High-strength Al-Zn-Mg-Cu Alloys[J]. Mater. Sci. Eng. A, 2016, 657: 269–28310.1016/j.msea.2016.01.039 ↗
25. Li M H, Yang Y Q, Feng Z Q, et al. Precipitation Sequence of η Phase along Low-angle Grain Boundaries in Al-Zn-Mg-Cu Alloy during Artificial Aging[J]. Trans. Nonferrous. Met. Soc. China, 2014, 24(7): 2061–206610.1016/S1003-6326(14)63312-4 ↗
26. American Society for Testing and Materials. Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatment Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution[S]. ASTM G110, 2009
27. Song R G, Yang F E, Blawert C, et al. Behavior of Stress Corrosion Cracking in a Magnesium Alloy[J]. J. Wuhan University of Technology-Mater. Sci. Ed., 2009, 24(1): 111–11310.1007/s11595-009-1111-y ↗
28. Qi W J, Song R G, Zhang Y, et al. A Study on Mechanical Properties and Hydrogen Embrittlement Susceptibility of 7075 Aluminum Alloy[J]. Corros. Eng. Sci. Technol., 2015, 50(6): 480–48610.1179/1743278215Y.0000000004 ↗