journal article·2012-02

Cathode erosion of graphite and Cu/C materials in airarcs

Chengyu Zhang, Shengru Qiao, Yiwen Liu, Zhimao Yang, Yaping Wang, Yong Guo

Publisher page

Abstract

Cathode erosion of graphite and Cu/C was studied in direct current arcs, which were ignited between two electrodes comprised of two kinds of carbon materials and a tungsten anode in air. The arced zones on the cathode surface were investigated by a scanning electron microscope. Also, the cathode erosion rates of the investigated materials were measured. The results show that two distinct zone can be seen on both cathodes. The eroded area was located at the zone just opposite to the anode and surrounded by a white zone. The arced surface on the Cu/C containing 9.3 % Cu is rougher than that of the pure graphite. Many particles with various sizes distributed on the Cu/C. The vaporization of Cu can lower the surface temperature and reduce the cathode erosion. Therefore, the cathode erosion rate of the Cu/C is lower than that of the pure graphite.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electrical Contact Performance and Analysis · Vacuum and Plasma Arcs · Electrical Fault Detection and Protection

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. A Uecker. Lead-free Carbon Brushes for Automotive Starters [J]. Wear, 2003, 255: 1 286–1 29010.1016/S0043-1648(03)00182-0 ↗
2. D He, R Manory. A Novel Electrical Contact Material with Improved Self-lubrication for Railway Current Collectors [J]. Wear, 2001, 249: 626–63610.1016/S0043-1648(01)00700-1 ↗
3. X C Ma, G Q He, D H He, et al. Sliding Wear Behavior of Copper-graphite Composite Material for Use in Maglev Transportation System [J]. Wear, 2008, 265: 1087–109210.1016/j.wear.2008.02.015 ↗
4. I Yasar, A Canakci, F Arslan. The Effect of Brush Spring Pressure on the Wear Behaviour of Copper-graphite Brushes with Electrical Current [J]. Tribol. Int., 2007, 40: 1 381–1 38610.1016/j.triboint.2007.03.005 ↗
5. S Kubo, K Kato. Effect of Arc Discharge on the Wear Rate and Wear Mode Transition of a Copper-impregnated Metallized Carbon Contact Strip Sliding Against a Copper Disk [J]. Tribol. Int., 1999, 32: 367–37810.1016/S0301-679X(99)00062-6 ↗
6. M Karasik, S J Zweben. Experiments and Modeling of an Instability of an Atmospheric Pressure Arc [J]. Phys. Plasmas, 2000, 7: 4 326–4 34010.1063/1.1288401 ↗
7. H Zhao, G C Barber, J Liu. Friction and Wear in High Speed Sliding with and without Electrical Current [J]. Wear, 2001, 249: 409–41410.1016/S0043-1648(01)00545-2 ↗
8. A Bouchoucha, H Zaidi, E K Kadiri, et al. Influence of Electric Fields on the Tribological Behaviour of Electrodynamical Copper/Steel Contacts [J]. Wear, 1997, 203–204: 434–44110.1016/S0043-1648(96)07424-8 ↗
9. J Meunier, S Coulombe, M Kandah. Erosion of Carbon Arc Cathodes Operating in the Thermo-field Electron Emission Mode [J]. Plasma Sources Sci. Technol., 2007, 16: 33–4110.1088/0963-0252/16/1/005 ↗
10. Y Zhang, Z M Yang, Y P Wang, et al. Cathode Spot Propagation on the Surface of Amorphous, Nanocrystalline and Crystalline Cu60Zr28Ti12 Cathodes [J]. Phys. Lett. A, 2003, 318: 435–43910.1016/j.physleta.2003.09.050 ↗
11. Z M Yang, Q L Zhang, C Y Zhang, et al. Vacuum Arc Characteristics on Nanocrystalline CuCr Alloys [J]. Phys. Lett. A, 2006, 81: 545–549
12. S Tanaka, T Matsumura. Characteristic Dynamic Behavior of Dc Arc Near Graphite Bar Electrodes with Short Gap [J]. J. Appl. Phys., 2001, 89: 4 247–4 25210.1063/1.1355720 ↗
13. E Muñoz-Serrano, E Casado, V Colomer,et al. Modeling and Experimental Investigation of Spot Dynamics on Graphite Cathodes in Dc Plasma Arcs at High Pressure [J]. J. Appl. Phys., 2006, 99, 043 303-1–043 3030-510.1063/1.2168033 ↗
14. A M Essiptchouk, L I Sharakhovsky, A Marotta. The Effect of Surface Electrode Temperature on Cold Electrode Erosion Behaviour [J]. Plasma Sources Sci. T., 2007, 16:1–610.1088/0963-0252/16/1/001 ↗