An Integrated Approach of GRA Coupled with Principal Component Analysis for Multi-Optimization of Shielded Metal Arc Welding (SMAW) Process
Source abstract
Abstract
Welding distortion is a critical issue as it leads to severe deterioration of structural integrity of welded work piece and dimensional precision. This study aims at studying the effects of shielded metal arc welding (SMAW) parameters on the evolution of mechanical properties, including tensile strength, impact toughness, and hardness, along with angular distortion on a welded joint from SA 516 grade 70. Such parameters are analyzed and optimized by employing the Taguchi method and Grey relational analysis. SA 516 grade 70 is commercially used for fabrication of storage tanks, boilers and pressure vessels. SMAW is investigated with three levels of root gap, groove angle, electrode diameter, and pre-heat temperature, which were varied on a butt joint in flat (1 G) position to determine their effects on response variables at room temperature. Nine experiments were designed using a Taguchi L9 orthogonal array, welded according to American Society of Mechanical Engineers (ASME) section IX, and samples were prepared and tested as per ASTM A 370. The Taguchi method and Grey relational analysis were employed to observe the most significant parameters and optimal levels that synergically yield improved responses. Results are validated by conducting confirmatory experiments that show good agreement with optimum results.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced machining processes and optimization · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Industrial Engineering, Jalozai Campus, University of Engineering and Technology Peshawar, Nowshera 24240, Pakistan
Department of Industrial Engineering, University of Engineering and Technology Peshawar, Peshawar 25120, Pakistan
Department of Mechanical Engineering, Imperial College London, London SW7 2AZ, UK
Department of Mechanical Engineering, School of Engineering, University of Birmingham, Birmingham B15 2TT, UK
References (70)
Show source-provided references
1. Investigations on dissimilar welding of P91/SS304L using Nickel-based electrodes10.1080/10426914.2020.1755041 ↗
2. Khamari, B.K., Dash, S.S., Karak, S.K., and Biswal, B.B. (2019). Effect of welding parameters on mechanical and microstructural properties of GMAW and SMAW mild steel joints. Ironmak. Steelmak., 1–8.10.1080/03019233.2019.1623592 ↗
3. Influence of welding consumables on tensile and impact properties of multi-pass SMAW Armox 500T steel joints vis-a-vis base metal10.1016/j.dt.2018.01.005 ↗
4. Effect of different post weld heat treatments on the mechanical properties of Cr-Mo boiler steel welded with SMAW process10.1016/j.matpr.2015.07.002 ↗
5. Effect of increasing deposition rate on the bead geometry of submerged arc welds10.1016/S0924-0136(97)00139-8 ↗
6. A practical approach towards mathematical modeling of deposition rate during twin-wire submerged arc welding10.1007/s00170-006-0847-1 ↗
7. Effect of thermomechanical processing on the microstructure and properties of a Cu-Fe-P alloy10.1007/s11665-014-1352-6 ↗
8. Coaxial arc weld pool viewing for process monitoring and control
9. Genetic algorithm based optimization of the process parameters for manual metal arc welding of dissimilar metal joint
10. Study the effect of shielded metal arc welding process parameters, cryo-treatment and preheating on welding characteristics and modelling by an artificial neural network10.7158/M12-046.2014.12.2 ↗
11. Optimised post-weld heat treatment procedures and heat input for welding 17–4PH stainless steel10.1179/136217199101537905 ↗
12. Optimization of process parameters of manual arc welding of mild steel using taguchi method
13. Predicting the tensile strength, impact toughness, and hardness of friction stir-welded AA6061-T6 using response surface methodology10.1007/s00170-016-8565-9 ↗
14. Seong, W.-J. (2019). Prediction and characteristics of angular distortion in multi-layer butt welding. Materials, 12.10.3390/ma12091435 ↗
15. The influence of thermal properties and preheating on residual stresses in welding
16. Influence of Welding Sequence on Residual Stresses Induced in As-Welded Plug Weld of Low-Carbon Steel Plate10.1007/s12666-019-01631-1 ↗
17. Optimization of Angular Distortion on Weld Joints Using Taguchi Approach10.17576/jkukm-2019-31(1)-03 ↗
18. Multi-response optimization on mechanical properties of silica fly ash filled polyester composites using taguchi-grey relational analysis10.1007/s12633-017-9660-8 ↗
19. Multi-objective optimization of some correlated process parameters in EDM of Inconel 800 using a hybrid approach10.1007/s40430-019-1805-9 ↗
20. Simultaneous optimization of woven fabric properties using principal component analysis10.1080/15440478.2017.1279994 ↗
21. Multi-objective optimization of manual metal arc welding process parameters for nano-structured hardfacing material using hybrid approach10.1016/j.measurement.2017.01.048 ↗
22. Parameter design in friction welding of Al/SiC/Al 2 O 3 composite using grey theory based principal component analysis (GT-PCA)10.1007/s40430-014-0294-0 ↗
23. Effect of Filler Metal Diameter on Weld Joint of Carbon Steel SA516 Gr 70 and Filler Metal SFA 5.17 in Submerged Arc Welding SAW
24. ASTM A 526/516 M—90 (1996). Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Services, ASTM International.
25. ASTM A 370 (2016). Standard Test Methods and Definitions for Mechanical for Mechanical Testing of Steel Products, ASTM International.
26. Prediction of welding distortion in butt joint of thin plates10.1016/j.matdes.2009.05.004 ↗
27. Effects of activating flux on the welded joint characteristics in gas metal arc welding10.1016/j.matdes.2009.11.043 ↗
28. Laser parameters optimization of surface treating of Al 6082-T6 with Taguchi method10.1016/j.optlastec.2019.105714 ↗
29. Analysis of welding groove angle and geometry on strength of armor steel10.1080/10426914.2012.709343 ↗
30. Influence of pre-and post-weld heating on weldability of modified 9Cr–1Mo (V–Nb) steel pipe under shielded metal arc and tungsten inert gas welding processes10.1179/136217104225012265 ↗
31. Numerical simulation of welding distortion in large structures10.1016/j.cma.2007.05.023 ↗
32. AWS (1992). Welding Handbook: Welding Processes, American Welding Society.
33. Effect of Welding Techniques (GTAW & SMAW) on the Microstructure & Mechanical Properties of Mild Steel SA 516 Gr. 70
34. Mechanical properties and microstructure of SMAW welded and thermically treated HSLA-80 steel10.1016/j.jmrt.2018.08.007 ↗
35. Metallurgical and mechanical properties of laser welded high strength low alloy steel10.1016/j.jare.2016.03.005 ↗
36. Influence of microstructural aspects on impact toughness of multi-pass submerged arc welded HSLA steel joints10.1016/j.matdes.2015.10.158 ↗
37. Kurt, H.I., Oduncuoglu, M., Yilmaz, N.F., Ergul, E., and Asmatulu, R. (2018). A comparative study on the effect of welding parameters of austenitic stainless steels using artificial neural network and Taguchi approaches with ANOVA analysis. Metals, 8.10.3390/met8050326 ↗
38. Analysis of mechanical properties and optimization of gas tungsten Arc welding (GTAW) parameters on dissimilar metal titanium (6Al4V) and aluminium 7075 by Taguchi and ANOVA techniques10.1016/j.jallcom.2016.05.006 ↗
39. Interfacial microstructure and optimization of friction welding by Taguchi and ANOVA method on SA 213 tube to SA 387 tube plate without backing block using an external tool10.1016/j.jallcom.2015.09.152 ↗
40. Multi Objective Optimization of Weld Parameters of Boiler Steel Using Fuzzy Based Desirability Function10.25103/jestr.071.05 ↗
41. Determination of optimum parameters with multi-performance characteristics in laser drilling—A grey relational analysis approach10.1007/s00170-010-2985-8 ↗
42. Optimization of multiple quality characteristics for polyether ether ketone injection molding process10.1007/BF02875773 ↗
43. Multi-response optimization of minimum quantity lubrication parameters using Taguchi-based grey relational analysis in turning of difficult-to-cut alloy Haynes 2510.1016/j.jclepro.2014.12.020 ↗
44. Analysis on drilling of glass fiber–reinforced polymer (GFRP) composites using grey relational analysis10.1080/10426914.2011.577865 ↗
45. Optimization of machining parameters of WEDM for Nimonic-75 alloy using principal component analysis integrated with Taguchi method
46. Monitoring of a machining process using kernel principal component analysis and kernel density estimation
47. EDF statistics for goodness of fit and some comparisons10.1080/01621459.1974.10480196 ↗
48. An Experimental Study on Effect of T-Joint’s Root Gap on Welding Properties10.4028/www.scientific.net/AMM.863.323 ↗
49. Optimization of Shielded Metal Arc Welding (SMAW) process for mild steel
50. Investigation of tensile properties of shielded metal arc weldments of AISI 1018 mild steel with preheating process10.1016/j.matpr.2019.10.167 ↗
51. Effect of plastic deformation on the formation of acicular ferrite10.1016/S0921-5093(03)00477-5 ↗
52. Studies on effects of welding parameters on the mechanical properties of welded low-carbon steel
53. Effect of welding variables on mechanical properties of low carbon steel welded joint
54. Microstructure-properties correlation in fiber laser welding of dual-phase and HSLA steels10.1016/j.msea.2014.04.034 ↗
55. Distortion control in TIG welding process with Taguchi approach
56. Effect of Groove Design on the Mechanical Properties of Shielded Metal Arc Welded Joints
57. Pathak, D., Singh, R.P., Gaur, S., and Balu, V. (2020). Influence of groove angle on hardness and reinforcement height of shielded metal arc welded joints for low carbon AISI 1016 steel plates. Mater. Today Proc.10.1016/j.matpr.2020.05.597 ↗
58. Effects of preheating temperature on cold cracks, microstructures and properties of high power laser hybrid welded 10Ni3CrMoV steel10.1016/j.matdes.2010.12.007 ↗
59. Prediction of welding residual stress in multi-pass butt-welded modified 9Cr–1Mo steel pipe considering phase transformation effects10.1016/j.commatsci.2005.06.010 ↗
60. A study on the influence of clamping on welding distortion10.1016/j.commatsci.2009.01.004 ↗
61. Characterization on strength and toughness of welded joint for Q550 steel10.1007/s12034-011-0039-y ↗
62. Methodology for predicting the angular distortion in multi-pass butt-joint welding10.1016/j.jmatprotec.2016.10.006 ↗
63. Effect of GTAW Parameters on Structure and Mechanical Properties of C86300 Weld Joint10.1007/s12666-014-0397-4 ↗
64. The effects of root opening on mechanical properties, deformation and residual stress of weldments
65. Numerical simulation to study the effect of tack welds and root gap on welding deformations and residual stresses of a pipe-flange joint10.1016/j.ijpvp.2005.06.008 ↗
66. Analysis of welding distortion due to narrow-gap welding of upper port plug10.1016/j.fusengdes.2010.05.025 ↗
67. Study of the effect of nano-silica particles on resin-bonded moulding sand properties and quality of casting10.1007/s12633-017-9705-z ↗
68. Effect of submerged arc welding parameters on microstructure of SA516 steel weld metal10.1179/000844311X13117643274794 ↗
69. Factors affecting weld metal properties in carbon and low alloy pressure vessel steels
70. Investigation on three different weldments on performance of SA516 Gr70 steel material10.1016/j.aej.2019.05.012 ↗