journal article·2017-07-04Open access

Effect of Molten Pool Size on Microstructure and Tensile Properties of Wire Arc Additive Manufacturing of Ti-6Al-4V Alloy

Qianru Wu, Jiping Lu, Changmeng Liu, Hongli Fan, Xuezhi Shi, Jie Fu, Shuyuan Ma

Materials· Volume 10· Issue 7

Abstract

Wire arc additive manufacturing (WAAM) technique is a cost-competitive and efficient technology to produce large structure components in industry domains. Mechanical properties are mainly dominated by the microstructure of the components, which is deeply affected by the molten pool size. In this work, to investigate the effect of the molten pool size on microstructure and mechanical properties of the components, a series of Ti-6Al-4V alloy blocks with different width of molten pool (WMP) ranging from 7 mm to 22 mm were deposited by adjusting the wire feed speed (WFS) from 100 cm/min to 500 cm/min. It is interesting to find that the macrostructure changes from columnar grains to equiaxial grains, and then returns to large columnar grains with the increase of WMP, which is mainly caused by the different cooling rates and thermal gradients. Nonetheless, the tensile properties of the components have a tendency to decline with the increase of WMP.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China

References (25)

Show source-provided references
1. Rapid prototyping of 4043 Al-alloy parts by vp-gtaw10.1016/j.jmatprotec.2004.01.058 ↗
2. Additive manufacturing of Ti-6AL-4V components by shaped metal deposition: Microstructure and mechanical properties10.1016/j.matdes.2009.11.032 ↗
3. A tool-path generation strategy for wire and arc additive manufacturing10.1007/s00170-014-5808-5 ↗
4. Selective laser melting-wire arc additive manufacturing hybrid fabrication of Ti-6AL-4V alloy: Microstructure and mechanical properties10.1016/j.msea.2016.12.065 ↗
5. Additive manufacturing of in 100 superalloy through scanning laser epitaxy for turbine engine hot-section component repair: Process development, modeling, microstructural characterization, and process control10.1007/s11661-015-2912-6 ↗
6. Microstructure and mechanical properties of wire and arc additive manufactured Ti-6Al-4V10.1007/s11661-012-1444-6 ↗
7. Obtaining fine microstructure and unsupported overhangs by low heat input pulse arc additive manufacturing10.1016/j.jmapro.2017.05.004 ↗
8. Microstructures and mechanical properties of Ti-6AL-4V parts fabricated by selective laser melting and electron beam melting10.1007/s11665-013-0658-0 ↗
9. Guo, J., Zhou, Y., Liu, C., Wu, Q., Chen, X., and Lu, J. (2016). Wire arc additive manufacturing of AZ31 magnesium alloy: Grain refinement by adjusting pulse frequency. Materials, 9.10.3390/ma9100823 ↗
10. Simonelli, M. (2014). Microstructure Evolution and Mechanical Properties of Selective Laser Melted Ti-6AL-4V. [Doctoral Thesis, Loughborough University].10.4028/www.scientific.net/KEM.627.125 ↗
11. Microstructure evolution of sub-critical annealed laser deposited Ti-6AL-4V alloy10.1016/j.matdes.2011.12.016 ↗
12. Weld bead modeling and process optimization in hybrid layered manufacturing10.1016/j.cad.2011.01.006 ↗
13. Three-dimensional numerical simulation of arc and metal transport in arc welding based additive manufacturing10.1016/j.ijheatmasstransfer.2016.06.084 ↗
14. Developing a realistic FE analysis method for the welding of a net single-bead-on-plate test specimen10.1016/j.jmatprotec.2007.04.080 ↗
15. A new finite element model for welding heat sources10.1007/BF02667333 ↗
16. Thermo-mechanical analysis of wire and arc additive layer manufacturing process on large multi-layer parts10.1016/j.commatsci.2011.06.023 ↗
17. Investigation of lagrangian and eulerian finite element methods for modeling the laser forming process10.1016/S0168-874X(03)00069-6 ↗
18. Klingbeil, N., Brown, C., Bontha, S., Kobryn, P., and Fraser, H. (, January August). Prediction microstructure in laser deposition titanium alloys. Proceedings of the Solid Freeform Fabrication Proceedings, Austin, TX, USA.
19. Ding, J. (2012). Thermo-Mechanical Analysis of Wire and Arc Additive Manufacturing Process. [Ph.D. Thesis, Cranfield University].
20. The laser additive manufacture of Ti-6AL-4V10.1007/s11837-001-0068-x ↗
21. Microstructure and texture evolution during solidification processing of Ti-6Al-4V10.1016/S0924-0136(02)00865-8 ↗
22. Fu, J., Gong, L., Zhang, Y., Wu, Q., Shi, X., Chang, J., and Lu, J. (2017). Microstructure and mechanical properties of Ti-6Al-4V fabricated by vertical wire feeding with axisymmetric multi-laser source. Appl. Sci., 7.10.3390/app7030227 ↗
23. Texture and crystal orientation in Ti-6Al-4V builds fabricated by shaped metal deposition10.1007/s11661-010-0255-x ↗
24. Influence of processing on microstructure and mechanical properties of (α + β) titanium alloys10.1016/S0921-5093(97)00778-8 ↗
25. Leyens, C., and Peters, M. (2003). Titanium and Titanium Alloys, Wiley-VCH.10.1002/3527602119 ↗