journal article·2019-07-23Open access

Comparison of Meshing Strategies in THR Finite Element Modelling

Alessandro Ruggiero, Roberto D’Amato, Saverio Affatato

Materials· Volume 12· Issue 14

Abstract

In biomechanics and orthopedics, finite element modelling allows simulating complex problems, and in the last few years, it has been widely used in many applications, also in the field of biomechanics and biotribology. As is known, one crucial point of FEM (finite element model) is the discretization of the physical domain, and this procedure is called meshing. A well-designed mesh is necessary in order to achieve accurate results with an acceptable computational effort. The aim of this work is to test a finite element model to simulate the dry frictionless contact conditions of a hip joint prosthesis (a femoral head against an acetabular cup) in a soft bearing configuration by comparing the performances of 12 common meshing strategies. In the simulations, total deformation of the internal surface of the cup, contact pressure, and the equivalent von Mises stress are evaluated by using loads and kinematic conditions during a typical gait, obtained from a previous work using a musculoskeletal multibody model. Moreover, accounting for appropriate mesh quality metrics, the results are discussed, underlining the best choice we identified after the large amount of numerical simulations performed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Orthopaedic implants and arthroplasty · Hip disorders and treatments · Total Knee Arthroplasty Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Industrial Engineering, University of Salerno, Via Giovanni Paolo II, nr. 132, 84084 Fisciano, Italy

Escuela Técnica Superior de Ingeniería y Diseño Industrial, Universidad Politécnica de Madrid, Roda de Valencia, 3, 28012 Madrid, Spain

Laboratorio di Tecnologia Medica, IRCCS Istituto Ortopedico Rizzoli, Via di Barbiano, 1/10, 40136 Bologna, Italy

References (21)

Show source-provided references
1. Affatato, S., Merola, M., and Ruggiero, A. (2018). Development of a Novel in Silico Model to Investigate the Influence of Radial Clearance on the Acetabular Cup Contact Pressure in Hip Implants. Materials (Basel), 11.10.3390/ma11081282 ↗
2. Ruggiero, A., Affatato, S., Merola, M., and De Simone, M.C. (2017, January 4–7). FEM analysis of metal on UHMWPE total hip prosthesis during normal walking cycle. Proceedings of the XXIII Conference of the Italian Association of Theoretical and Applied Mechanics, Salerno, Italy.
3. A new method to analyse the mechanical behaviour of skeletal parts10.3109/17453677208998949 ↗
4. An Efficient and Accurate Prediction of the Stability of Percutaneous Fixation of Acetabular Fractures with Finite Element Simulation10.1115/1.4004821 ↗
5. Ruggiero, A., Merola, M., and Affatato, S. (2018). Finite Element Simulations of Hard-On-Soft Hip Joint Prosthesis Accounting for Dynamic Loads Calculated from a Musculoskeletal Model during Walking. Materials (Basel), 11.10.3390/ma11040574 ↗
6. Analysis and Fem Simulation Methodology of Dynamic Behavior of Human Rotator Cuff in Repetitive Routines: Musician Case Study10.1007/s10916-018-0908-7 ↗
7. Behavior under Load of A Human Shoulder: Finite Element Simulation and Analysis10.1007/s10916-019-1248-y ↗
8. Impact of mesh quality parameters on elements such as beam, shell and 3D solid in structural analysis
9. Comparison of hexahedral and tetrahedral elements in finite element analysis of the foot and footwear10.1016/j.jbiomech.2011.05.006 ↗
10. Benzley, S.E., Perry, E., Merkley, K., Clark, B., and Sjaardama, G. (1995, January 16–17). A comparison of all hexagonal and all tetrahedral finite element meshes for elastic and elasto-plastic analysis. Proceedings of the 4th International Meshing Roundtable, Sandia National Laboratories, Albuquerque, NM, USA.
11. Finite element modeling mesh quality, energy balance and validation methods: A review with recommendations associated with the modeling of bone tissue10.1016/j.jbiomech.2013.03.022 ↗
12. (2019, May 18). ANSYS Meshing User’s Guide. Available online: https://www.ansys.com/products/platform/ansys-meshing.
13. Rice, J.R. (1985). The Aspect Ratio Significant for Finite Element Problems, Purdue University. 85-535.
14. Felippa, C.A. (2019, May 18). Introduction to Finite Element Methods. Available online: https://vulcanhammernet.files.wordpress.com/2017/01/ifem.pdf.
15. Comparison of accuracy criteria for approximation of conservative fields on tetrahedra
16. Does metal transfer affect the tribological behaviour of femoral heads? Roughness and phase transformation analyses on retrieved zirconia and Biolox® Delta composites10.1016/j.compositesb.2016.02.020 ↗
17. On the biotribology of total knee replacement: A new roughness measurements protocol on in vivo condyles considering the dynamic loading from musculoskeletal multibody model10.1016/j.measurement.2017.08.008 ↗
18. Lee, H.-H. (2012). Finite Element Simulations with ANSYS Workbench 14: Theory, Applications, Case Studies, Schroff Development Corp.
19. Affatato, S., Ruggiero, A., Jaber, S.A., Merola, M., and Bracco, P. (2018). Wear behaviours and oxidation effects on different uhmwpe acetabular cups using a hip joint simulator. Materials (Basel), 11.10.3390/ma11030433 ↗
20. Tribological performances of total knee prostheses: Roughness measurements on medial and lateral compartments of retrieved femoral components10.1016/j.measurement.2018.11.072 ↗
21. Affatato, S., and Ruggiero, A. (2019). A Critical Analysis of TKR In Vitro Wear Tests Considering Predicted Knee Joint Loads. Materials, 12.10.3390/ma12101597 ↗