journal article·2018-09-25Open access

Insights into Galvanic Corrosion Behavior of Ti-Cu Dissimilar Joint: Effect of Microstructure and Volta Potential

Ehsan Rahimi, Ali Rafsanjani-Abbasi, Amin Imani, Saman Hosseinpour, Ali Davoodi

Materials· Volume 11· Issue 10

Abstract

The effect of microstructure on corrosion behavior of a solid-state explosion welded Ti-Cu bimetal is investigated by means of alternating current-direct current (AC-DC) electrochemical measurements, optical microscopy, scanning electron microscopy, and scanning Kelvin probe force microscopy (SKPFM). The results indicate that the titanium regions in the welding interface, local melted zone (LMZ), and LMZ-Cu interface are potential sites for initiation of corrosion attacks. SKPFM mapping clearly shows that before exposure of the sample to a 3.5% NaCl corrosive solution and at the beginning of the exposure, the Cu side of the bimetal has a higher Volta potential in comparison to that of the Ti region, and thus acts as a cathode. Electrochemical measurements also confirm that titanium acts as an anode and copper as a cathode, in the first moments of immersion, in accordance with macroscopic observations and SKPFM results. However, by growing a passive layer of titanium oxide and titanium hydroxide on the Ti side after about 1 h exposure to the corrosive medium, the titanium side becomes nobler and the polarity arrangement in the galvanic couple reverses.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Materials and Metallurgical Engineering Department, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad 9177948974, Iran

Polytechnic Department of Engineering and Architecture, University of Udine, Via del Cotonificio 108, 33100 Udine, Italy

Materials and Polymers Engineering Department, Hakim Sabzevari University, Sabzevar 9617976487, Iran

Institute of Particle Technology (LFG), Friedrich-Alexander-Universität-Erlangen-Nürnberg (FAU), Cauerstraße 4, 91058 Erlangen, Germany

References (56)

Show source-provided references
1. High cooling rates and metastable phases at the interfaces of explosively welded materials10.1016/j.actamat.2017.06.038 ↗
2. Electrical, Corrosion, and Mechanical Properties of Aluminum-Copper Joints Produced by Explosive Welding10.1007/s11665-012-0203-6 ↗
3. A new concept of universal substitutive explosive welding10.1016/j.matdes.2016.11.053 ↗
4. A novel combination approach for the preparation of superhydrophobic surface on copper and the consequent corrosion resistance10.1016/j.corsci.2016.04.015 ↗
5. Mechanistic studies of corrosion product flaking on copper and copper-based alloys in marine environments10.1016/j.corsci.2014.03.028 ↗
6. Imidazole based compounds as copper corrosion inhibitors in seawater10.1016/j.molliq.2016.11.038 ↗
7. Corrosion and inhibition of copper in hydrocarbon solution on a molecular level investigated using neutron reflectometry and XPS10.1016/j.corsci.2016.11.010 ↗
8. Triazolyl-acylhydrazone derivatives as novel inhibitors for copper corrosion in chloride solutions10.1016/j.corsci.2015.08.022 ↗
9. The corrosion behavior of copper alloys, stainless steels and titanium in seawater10.1016/0010-938X(94)90008-6 ↗
10. Effects of Temperature and Sulfate on the Pitting Corrosion of Titanium in High-Temperature Chloride Solutions10.1149/2.0541504jes ↗
11. Scanning Electrochemical Microscopy of Precursor Sites for Pitting Corrosion on Titanium10.1149/1.2220897 ↗
12. Interfacial characterization and mechanical property of Ti/Cu clad sheet produced by explosive welding and annealing10.1007/s11595-015-1295-2 ↗
13. Accessing collision welding process window for titanium/copper welds with vaporizing foil actuators and grooved targets10.1016/j.jmatprotec.2014.03.007 ↗
14. Examination of copper/stainless steel joints formed by explosive welding10.1016/j.matdes.2004.07.021 ↗
15. Recent developments in explosive welding10.1016/j.matdes.2010.10.017 ↗
16. Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel10.1016/S0022-3115(03)00194-6 ↗
17. Microstructural and mechanical properties of Cu–Ti plates bonded through explosive welding process10.1016/j.jmatprotec.2005.02.264 ↗
18. Effect of explosive characteristics on the explosive welding of stainless steel to carbon steel in cylindrical configuration10.1016/j.matdes.2013.03.069 ↗
19. Effect of explosive mixture on quality of explosive welds of copper to aluminium10.1016/j.matdes.2016.01.116 ↗
20. The effect of explosive welding parameters on metallurgical and mechanical interfacial features of Inconel 625/plain carbon steel bimetal plate10.1016/j.msea.2012.07.012 ↗
21. Weldability window and the effect of interface morphology on the properties of Al/Cu/Al laminated composites fabricated by explosive welding10.1016/j.matdes.2015.07.114 ↗
22. Microstructure and property inhomogeneity investigations of bonded Zr/Ti/steel trimetallic sheet fabricated by explosive welding10.1016/j.jallcom.2016.12.213 ↗
23. Microstructural and microanalysis investigations of bond titanium grade1/low alloy steel st52-3N obtained by explosive welding10.1016/j.jallcom.2016.02.120 ↗
24. Hierarchical microstructure of explosive joints: Example of titanium to steel cladding10.1016/j.msea.2010.11.092 ↗
25. Correlation of surface Volta potential with galvanic corrosion initiation sites in solid-state welded Ti-Cu bimetal using AFM-SKPFM10.1016/j.corsci.2018.06.026 ↗
26. American Society for Testing Materials (2017). Standard Guide for Preparation of Metallographic Specimens, ASTM International. ASTM E3-11(2017).
27. Establishing a correlation between interfacial microstructures and corrosion initiation sites in Al/Cu joints by SEM–EDS and AFM–SKPFM10.1016/j.corsci.2013.10.039 ↗
28. Influence of metal carbides on dissolution behavior of biomedical CoCrMo alloy: SEM, TEM and AFM studies10.1016/j.electacta.2011.08.028 ↗
29. High-resolution Kelvin probe microscopy in Corros. Sci.: Scanning Kelvin probe force microscopy (SKPFM) versus classical scanning Kelvin probe (SKP)10.1016/j.electacta.2007.03.016 ↗
30. Characterization of AA2024-T3 by scanning Kelvin probe force microscopy10.1149/1.1838633 ↗
31. The effect of annealing on the interface microstructure and mechanical characteristics of AZ31B/AA6061 composite plates fabricated by explosive welding10.1016/j.matdes.2014.08.025 ↗
32. Static and fatigue tests of bimetal Zr-steel made by explosive welding10.1016/j.engfailanal.2016.12.022 ↗
33. Structural properties of Ti/Al clads manufactured by explosive welding and annealing10.1016/j.matdes.2015.11.087 ↗
34. Control of energetic conditions by employing interlayer of different thickness for explosive welding of titanium/304 stainless steel10.1016/j.jmatprotec.2007.05.002 ↗
35. Effect of alloying elements on interdiffusion phenomena in explosive clads of 304LSS/Ti–5Ta–2Nb alloy10.1007/s10853-016-9832-8 ↗
36. The Cu−Ti (Copper-Titanium) system10.1007/BF02880329 ↗
37. Solid state diffusion bonding of titanium to steel using a copper base alloy as interlayer10.1016/j.jmatprotec.2008.06.014 ↗
38. Saboktakin, M., Razavi, G.R., and Monajati, H. (2011). The Investigate Metallurgical Properties of Roll BondingTitanium Clad Steel. IJAPM, 177–180.10.7763/IJAPM.2011.V1.34 ↗
39. Corrosion behaviour and galvanic coupling of titanium and welded titanium in LiBr solutions10.1016/j.corsci.2006.07.007 ↗
40. Investigation on passivity of titanium under steady-state conditions in acidic solutions10.1016/j.matchemphys.2010.12.028 ↗
41. Structure and composition of passive titanium oxide films10.1016/S0921-5107(97)00043-3 ↗
42. Galvanic corrosion behavior of copper/titanium galvanic couple in artificial seawater10.1016/S1003-6326(14)63097-1 ↗
43. Water soluble corrosion inhibitors for copper in 3.5 wt% sodium chloride solution10.1016/j.corsci.2017.05.009 ↗
44. Microstructure and corrosion characterization of the interfacial region in dissimilar friction stir welded AA5083 to AA702310.1016/j.corsci.2016.02.027 ↗
45. Corrosion mechanisms in titanium oxide-based films produced by anodic treatment10.1016/j.electacta.2017.03.011 ↗
46. McCafferty, E. (2010). Introduction to Corrosion Science, Springer. [1st ed.].10.1007/978-1-4419-0455-3 ↗
47. Corrosion Behavior of Titanium in Artificial Saliva by Lactic Acid10.3390/ma7085528 ↗
48. Green approach to fabrication of a super-hydrophobic film on copper and the consequent corrosion resistance10.1016/j.corsci.2013.11.055 ↗
49. Some aspects of the role of inhibitors in the corrosion of copper in tap water as observed by cyclic voltammetry10.1016/j.corsci.2015.11.005 ↗
50. Investigation of pitting resistance of titanium based on a modified point defect model10.1016/j.corsci.2010.11.015 ↗
51. An Electrochemical Investigation of Localized Corrosion on Titanium in Chloride Environments10.5006/1.3581969 ↗
52. Effect of Near-Ambient Temperature Changes on the Galvanic Corrosion of an AA2024-T3 and Mild Steel Couple10.1149/2.0551501jes ↗
53. Galvanic corrosion associated with SM 80SS steel and Ni-based alloy G3 couples in NaCl solution10.1016/j.electacta.2008.04.029 ↗
54. Combination of AFM, SKPFM, and SIMS to study the corrosion behavior of S-phase particles in AA2024-T35110.1149/1.2833315 ↗
55. The influence of microstructure on the corrosion behaviour of AZ91D studied by scanning Kelvin probe force microscopy and scanning Kelvin probe10.1016/j.corsci.2005.05.008 ↗
56. Unusual Correlation between SKPFM and Corrosion of Nickel Aluminum Bronzes10.1149/2.0391709jes ↗