Additively Manufactured NiTi and NiTiHf Alloys: Estimating Service Life in High-Temperature Oxidation
Source abstract
Abstract
In this study, the effect of the addition of Hf on the oxidation behavior of NiTi alloy, which was processed using additive manufacturing and casting, is studied. Thermogravimetric analyses (TGA) were performed at the temperature of 500, 800, and 900 °C to assess the isothermal and dynamic oxidation behavior of the Ni50.4Ti29.6Hf20 at.% alloys for 75 h in dry air. After oxidation, X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were used to analyze the oxide scale formed on the surface of the samples during the high-temperature oxidation. Two stages of oxidation were observed for the NiTiHf samples, an increasing oxidation rate during the early stage of oxidation followed by a lower oxidation rate after approximately 10 h. The isothermal oxidation curves were well matched with a logarithmic rate law in the initial stage and then by parabolic rate law for the next stage. The formation of multi-layered oxide was observed for NiTiHf, which consists of Ti oxide, Hf oxide, and NiTiO3. For the binary alloys, results show that by increasing the temperature, the oxidation rate increased significantly and fitted with parabolic rate law. Activation energy of 175.25 kJ/mol for additively manufactured (AM) NiTi and 60.634 kJ/mol for AM NiTiHf was obtained.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Shape Memory Alloy Transformations · High Entropy Alloys Studies · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical, Industrial, and Manufacturing Engineering, The University of Toledo, Toledo, OH 43606, USA
References (50)
Show source-provided references
1. Loading influence on the corrosion assessment during stress-induced martensite reorientation in nickel-titanium SMA10.1088/1361-665X/ab681d ↗
2. Nematollahi, M., Mehrabi, R., Callejas, M.A., Elahinia, H., and Elahinia, M. (2018, January 5–8). A two-way architectural actuator using NiTi SE wire and SME spring. Proceedings of the Active and Passive Smart Structures and Integrated Systems XII, Denver, CO, USA.10.1117/12.2299817 ↗
3. Nematollahi, M., Baghbaderani, K.S., Amerinatanzi, A., Zamanian, H., and Elahinia, M. (2019). Application of NiTi in Assistive and Rehabilitation Devices: A Review. Bioengineering, 6.10.3390/bioengineering6020037 ↗
4. Effect of Temperature on the Fracture Toughness of a NiTiHf High Temperature Shape Memory Alloy10.1007/s40830-019-00245-2 ↗
5. High temperature shape memory alloys10.1179/095066010X12646898728363 ↗
6. High temperature shape memory alloy Ni50.3Ti29.7Hf20torque tube actuators10.1088/1361-665X/aa7ef4 ↗
7. Jahadakbar, A., Nematollahi, M., Safaei, K., Bayati, P., Giri, G., Dabbaghi, H., Dean, D., and Elahinia, M. (2020). Design, Modeling, Additive Manufacturing, and Polishing of Stiffness-Modulated Porous Nitinol Bone Fixation Plates Followed by Thermomechanical and Composition Analysis. Metals, 10.10.3390/met10010151 ↗
8. Haghgouyan, B., Young, B., Karaman, I., and Lagoudas, D.C. (2019, January 4–6). Fracture toughness of martensitic NiTiHf high-temperature shape memory alloy. Proceedings of the Behavior and Mechanics of Multifunctional Materials XIII, Denver, CO, USA.10.1117/12.2514432 ↗
9. Fabrication of NiTi through additive manufacturing: A review10.1016/j.pmatsci.2016.08.001 ↗
10. Mechanical and shape memory properties of triply periodic minimal surface (TPMS) NiTi structures fabricated by selective laser melting
11. Effect of SLM Parameters on Transformation Temperatures of Shape Memory Nickel Titanium Parts10.1002/adem.201300558 ↗
12. Spatial Control of Functional Response in 4D-Printed Active Metallic Structures10.1038/srep46707 ↗
13. Tailoring Selective Laser Melting Process Parameters for NiTi Implants10.1007/s11665-012-0318-9 ↗
14. On the development of high quality NiTi shape memory and pseudoelastic parts by additive manufacturing10.1088/0964-1726/23/10/104002 ↗
15. A prediction model for finding the optimal laser parameters in additive manufacturing of NiTi shape memory alloy10.1007/s00170-019-04596-z ↗
16. Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties
17. Nematollahi, M., Jahadakbar, A., Mahtabi, M.J., Elahinia, M., and Namatollahi, M. (2019). Additive manufacturing (AM). Met. Biomed. Devices, 331–353.10.1016/B978-0-08-102666-3.00012-2 ↗
18. Nishida, K., and Narita, T. (1988). Introduction to High Temperature Oxidation of Metals, Maruze.
19. Ghayoor, M., Mirzababaei, S., Lee, K., He, Y., Chang, C., Paul, B.K., and Pasebani, S. (2019). Strengthening of 304L Stainless Steel by Addition of Yttrium Oxide and Grain Refinement during Selective Laser Melting, Annual International Solid Freeform Fabrication Symposium.
20. Advances in High Temperature Materials for Additive Manufacturing10.1088/1757-899X/226/1/012176 ↗
21. Microstructural Analysis of Additively Manufactured 304L Stainless Steel Oxide Dispersion Strengthened Alloy10.1017/S1431927619013709 ↗
22. Oxidation behavior of equiatomic TiNi alloy in high temperature air environment10.1016/0921-5093(96)10409-3 ↗
23. Surface oxidation of NiTi shape memory alloy10.1016/S0142-9612(02)00244-2 ↗
24. Oxidation Behavior of Ti 50 Ni 40 Cu 10 Shape-Memory Alloy in 700–1000 °C Air10.1007/s11085-008-9135-9 ↗
25. Smialek, J.L., Humphrey, D.L., and Noebe, R.D. (2007). Oxidation Kinetics of a NiPtTi High Temperature Shape Memory Alloy, NASA Glenn Research Center.
26. Comparative Oxidation Kinetics of a NiPtTi High Temperature Shape Memory Alloy10.1007/s11085-010-9202-x ↗
27. High temperature oxidation behavior of Ti–Ni–Hf shape memory alloy10.1016/j.tca.2014.02.016 ↗
28. Additive Manufacturing of Ni-Rich NiTiHf 20: Manufacturability, Composition, Density, and Transformation Behavior10.1007/s40830-019-00214-9 ↗
29. Shape memory behavior of NiTiHf alloys fabricated by selective laser melting10.1016/j.scriptamat.2019.11.056 ↗
30. Khanna, A.S. (2002). Introduction to High Temperature Oxidation and Corrosion, ASM International.
31. Atkins, P., and de Paula, J. (2011). Physical Chemistry for the Life Sciences, Oxford University Press.
32. High temperature oxidation behavior of NiTiNb intermetallic alloys10.1016/j.intermet.2007.01.005 ↗
33. Tsao, T.-K., Yeh, A.-C., Kuo, C.-M., and Murakami, H. (2016). High Temperature Oxidation and Corrosion Properties of High Entropy Superalloys. Entropy, 18.10.3390/e18020062 ↗
34. The surface oxidation behavior of Ni–45.16%Ti shape memory alloys at different temperatures10.1007/s10973-013-3208-y ↗
35. Atkins, P., de Paula, J., and Keeler, J. (2018). Atkins’ Physical Chemistry, Oxford University Press.
36. He, B., Xu, G., Zhou, M., and Yuan, Q. (2016). Effect of Oxidation Temperature on the Oxidation Process of Silicon-Containing Steel. Metals, 6.10.3390/met6060137 ↗
37. Surface conditions of Nitinol wires, tubing, and as-cast alloys. The effect of chemical etching, aging in boiling water, and heat treatment10.1002/jbm.b.10001 ↗
38. Li, L., Gong, X., Ye, X., Teng, J., Nie, Y., Li, Y., and Lei, Q. (2018). Influence of Building Direction on the Oxidation Behavior of Inconel 718 Alloy Fabricated by Additive Manufacture of Electron Beam Melting. Materials, 11.10.3390/ma11122549 ↗
39. Hirnyj, S.I. (2012). Thermochemistry of Oxide Films Formed on Zr-Based Metallic Glasses, Lviv Polytechnic National University Institutional Repository.
40. Kekare, S.A., Shelton, D.K., and Aswath, P.B. (1993). Oxidation of High-Temperature Intermetallics, The Minerals, Metals Materials Society.
41. Diffusion of zinc in alpha brass
42. The discovery and acceptance of the Kirkendall Effect: The result of a short research career10.1007/BF02914706 ↗
43. Oxidation behavior of TiNi shape memory alloy at 450–750 °C10.1016/S0921-5093(03)00287-9 ↗
44. Oxide Scales Formed on NiTi and NiPtTi Shape Memory Alloys10.1007/s11661-011-1036-x ↗
45. Farjam, N., Nematollahi, M., Andani, M.T., Mahtabi, M.J., and Elahinia, M. (2020). Effects of size and geometry on the thermomechanical properties of additively manufactured NiTi shape memory alloy. Int. J. Adv. Manuf. Technol., 1–10.10.1007/s00170-020-05071-w ↗
46. Achieving superelasticity in additively manufactured NiTi in compression without post-process heat treatment10.1038/s41598-018-36641-4 ↗
47. On the effects of selective laser melting process parameters on microstructure and thermomechanical response of Ni-rich NiTi10.1016/j.actamat.2017.10.072 ↗
48. Biffi, C.A., Bassani, P., Nematollahi, M., Moghaddam, N.S., Amerinatanzi, A., Mahtabi, M., Elahinia, M., and Tuissi, A. (2019). Effect of Ultrasonic Nanocrystal Surface Modification on the Microstructure and Martensitic Transformation of Selective Laser Melted Nitinol. Materials, 12.10.3390/ma12193068 ↗
49. Selective laser melting additive manufactured Inconel 718 superalloy parts: High-temperature oxidation property and its mechanisms10.1016/j.optlastec.2014.03.008 ↗
50. Corrosion of metallic materials fabricated by selective laser melting10.1038/s41529-019-0086-1 ↗