journal article·2021-02-12Open access

A Comparative Analysis of Laser Additive Manufacturing of High Layer Thickness Pure Ti and Inconel 718 Alloy Materials Using Finite Element Method

Sapam Ningthemba Singh, Sohini Chowdhury, Yadaiah Nirsanametla, Anil Kumar Deepati, Chander Prakash, Sunpreet Singh, Linda Yongling Wu, Hongyu Y. Zheng, Catalin Pruncu

Materials· Volume 14· Issue 4

Abstract

Investigation of the selective laser melting (SLM) process, using finite element method, to understand the influences of laser power and scanning speed on the heat flow and melt-pool dimensions is a challenging task. Most of the existing studies are focused on the study of thin layer thickness and comparative study of same materials under different manufacturing conditions. The present work is focused on comparative analysis of thermal cycles and complex melt-pool behavior of a high layer thickness multi-layer laser additive manufacturing (LAM) of pure Titanium (Ti) and Inconel 718. A transient 3D finite-element model is developed to perform a quantitative comparative study on two materials to examine the temperature distribution and disparities in melt-pool behaviours under similar processing conditions. It is observed that the layers are properly melted and sintered for the considered process parameters. The temperature and melt-pool increases as laser power move in the same layer and when new layers are added. The same is observed when the laser power increases, and opposite is observed for increasing scanning speed while keeping other parameters constant. It is also found that Inconel 718 alloy has a higher maximum temperature than Ti material for the same process parameter and hence higher melt-pool dimensions.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, North Eastern Regional Institute of Science and Technology, Nirjuli 791109, India

Department of Mechanical Engineering, National Institute of Technology Silchar, Silchar 788010, India

College of Applied Industrial Technology, Jazan University, Jizan 45142, Saudi Arabia

School of Mechanical Engineering, Lovely Professional University, Phagwara 144411, India

Department of Mechanical Engineering, Shandong University of Technology, Zibo 255000, China

Mechanical Engineering, National University of Singapore, Singapore 119077, Singapore

Mechanical Engineering, Imperial College, Exhibition Rd., London SW7 2AZ, UK

Design, Manufacturing & Engineering Management, University of Strathclyde, Glasgow G1 1XJ, UK

References (72)

Show source-provided references
1. Ductility of a Ti-6Al-4V alloy produced by selective laser melting of pre-alloyed powders10.1108/13552541011083371 ↗
2. Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti–6Al–4V10.1016/j.msea.2013.04.099 ↗
3. Microstructures and mechanical properties of electron beam-rapid manufactured Ti–6Al–4V biomedical prototypes compared to wrought Ti–6Al–4V10.1016/j.matchar.2008.07.006 ↗
4. Fatigue performance evaluation of selective laser melted Ti–6Al–4V10.1016/j.msea.2014.01.041 ↗
5. Balichakra, M., Krishna, P., Balla, V.K., and Das, M. (2016). Understanding Thermal Behavior in Laser Processing of Titanium Aluminide Alloys. Proc. Int. India Manuf. Technol. Des. Res. Conf., 73–77.
6. State-of-the-art of surface integrity induced by tool wear effects in machining process of titanium and nickel alloys: A review10.1016/j.measurement.2018.09.045 ↗
7. Additive manufacturing (3D printing): A review of materials, methods, applications and challenges10.1016/j.compositesb.2018.02.012 ↗
8. Development of thermal model for the determination of SLM process parameters10.1016/j.optlastec.2020.106825 ↗
9. Influence of SLM process parameters on the surface finish, porosity rate and fatigue behavior of as-built Inconel 625 parts10.1016/j.jmatprotec.2017.12.043 ↗
10. Optimization of processing parameters and establishment of a relationship between microstructure and mechanical properties of SLM titanium alloy10.1016/j.optlastec.2018.11.014 ↗
11. The effect of SLM process parameters on density, hardness, tensile strength and surface quality of Ti-6Al-4V
12. Factor Analysis of Selective Laser Melting Process Parameters with Normalised Quantities and Taguchi Method10.1016/j.optlastec.2019.105592 ↗
13. Influence of Process Parameters on Surface Roughness of Aluminum Parts Produced by DMLS10.1007/s00170-012-4688-9 ↗
14. Taguchi Optimization of the Surface Finish Obtained by Laser Ablation on Selective Laser Molten Steel Parts10.1016/j.procir.2013.09.079 ↗
15. Experimental Study for Effects of Process Parameters of Selective Laser Sintering for AlSi10mg
16. Porosity Content Control of CoCrMo and Titanium Parts by Taguchi Method Applied to Selective Laser Melting Process Parameter10.1108/RPJ-09-2013-0092 ↗
17. Sathish, S., Anandakrishnan, V., Dillibabu, V., Muthukannan, D., and Balamuralikrishnan, N. (2019). Optimization of Coefficient of Friction for Direct Metal Laser Sintered Inconel 718. Adv. Manuf. Technol., 371–379.10.1007/978-981-13-6374-0_43 ↗
18. Investigation of Electrochemical Post-Processing Procedure for Ti-6AL-4V Lattice Structure Manufactured by Direct Metal Laser Sintering (DMLS)10.1007/s00170-019-03996-5 ↗
19. Parametric Optimization of Laser Deposited High Entropy Alloys Using Response Surface Methodology (RSM)10.1007/s00170-020-05781-1 ↗
20. Selective Laser Melting of ALSi10MgAlloy: Process Optimisation and Mechanical Properties Development10.1016/j.matdes.2014.09.044 ↗
21. Optimization of SLM Process Parameters for Ti6Al4V Medical Implants10.1108/RPJ-05-2018-0112 ↗
22. Fotovvati, B., Balasubramanian, M., and Asadi, E. (2020). Modeling and Optimization Approaches of Laser-Based Powder-Bed Fusion Process for Ti-6Al-4V Alloy. Coatings, 10.10.3390/coatings10111104 ↗
23. Modelling of Laser Powder Bed Fusion Process and Analysing the Effective Parameters on Surface Characteristics of Ti-6Al-4V10.1016/j.ijmecsci.2019.105299 ↗
24. Alimardani, M., Paul, C.P., Toyserkani, E., and Khajepour, A. (2018). Multiphysics Modelling of Laser Solid Freeform Fabrication Techniques. Woodhead Publishing Series in Welding and Other Joining Technologies, Advances in Laser Materials Processing, Woodhead Publishing. [2nd ed.].10.1016/B978-0-08-101252-9.00022-4 ↗
25. A comprehensive analytical model for laser powder-fed additive manufacturing
26. Scaling laws for the additive manufacturing10.1016/j.jmatprotec.2018.02.034 ↗
27. Finite element analysis and experimental validation of the thermomechanical behavior in laser solid forming of Ti-6Al-4V
28. Finite element simulation of thermal behavior in single-track multiple-layers thin wall without-support during selective laser melting10.1016/j.jmapro.2019.04.019 ↗
29. Numerical investigation on heat transfer of multi-laser processing during selective laser melting of AlSi10Mg10.1016/j.rinp.2018.11.075 ↗
30. Cao, L. (2020). Workpiece-scale numerical simulations of SLM molten pool dynamic behavior of 316L stainless steel. Comput. Math. Appl.10.1016/j.camwa.2020.04.020 ↗
31. A Uniform-Gaussian distributed heat source model for analysis of residual stress field of S355 steel T welding10.1016/j.advengsoft.2018.09.003 ↗
32. Ning, J., Sievers, D.E., Garmestani, H., and Liang, S.Y. (2019). Analytical modeling of in-process temperature in powder bed additive manufacturing considering laser power absorption, latent heat, scanning strategy, and powder packing. Materials, 12.10.3390/ma12050808 ↗
33. Cao, L., and Yuan, X. (2019). Study on the numerical simulation of the SLM molten pool dynamic behavior of a nickel-based superalloy on the workpiece scale. Materials, 12.10.3390/ma12142272 ↗
34. Study of the Gaussian distribution heat source model applied to numerical thermal simulations of TIG welding processes
35. Adaptive volumetric heat source models for laser beam and laser + pulsed GMAW hybrid welding processes10.1007/s00170-011-3274-x ↗
36. Coupled thermal-mechanical-contact analysis of hot cracking in laser welded lap joints10.2351/1.4983249 ↗
37. Experimental investigation and finite element simulation of laser beam welding induced residual stresses and distortions in thin sheets of AA 6056-T410.1016/j.msea.2010.01.054 ↗
38. Analysis of hot cracking during lap joint laser welding processes using the melting state-based thermomechanical modeling approach10.1007/s00170-017-1157-5 ↗
39. Soldner, D., Greiner, S., Burkhardt, C., Drummer, D., Steinmann, P., and Mergheim, J. (2020). Numerical and experimental investigation of the isothermal assumption in selective laser sintering of PA12. Addit. Manuf., 101676.10.1016/j.addma.2020.101676 ↗
40. Numerical analysis of residual stress evolution of AlSi10Mg manufactured by selective laser melting10.1016/j.ijleo.2017.02.060 ↗
41. Numerical analysis of heat transfer during multi-layer selective laser melting of AlSi10Mg10.1016/j.ijleo.2016.06.115 ↗
42. Numerical investigation of heat current study across different platforms in SLM processed multi-layer AlSi10Mg10.1016/j.ijleo.2018.05.081 ↗
43. Residual stress measurements on AISI 316L samples manufactured by selective laser melting
44. An improved prediction of residual stresses and distortion in additive manufacturing10.1016/j.commatsci.2016.10.003 ↗
45. Role of molten pool mode on formability, microstructure and mechanical properties of selective laser melted Ti-6Al-4V alloy10.1016/j.matdes.2016.08.036 ↗
46. Role of scanning strategy on residual stress distribution in Ti-6Al-4V alloy prepared by selective laser melting10.1016/j.ijleo.2018.05.128 ↗
47. 3D finite element temperature field modelling for direct laser fabrication10.1007/s00170-008-1785-x ↗
48. Direct metal laser fabrication: Machine development and experimental work10.1007/s00170-009-2174-9 ↗
49. Martínez, S., Ortega, N., Celentano, D., Sánchez Egea, A.J., Ukar, E., and Lamikiz, A. (2020). Analysis of the part distortions for inconel 718 SLM: A case study on the NIST test artifact. Materials, 13.10.3390/ma13225087 ↗
50. Critical role of scan strategies on the development of microstructure, texture, and residual stresses during laser powder bed fusion additive manufacturing
51. Rough surfaces with enhanced heat transfer for electronics cooling by direct metal laser sintering10.1016/j.ijheatmasstransfer.2014.03.037 ↗
52. The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting10.1016/j.jmatprotec.2018.10.015 ↗
53. Comparison study of numerical analysis for heat transfer and fluid flow under two different laser scan pattern during selective laser melting10.1016/j.ijleo.2016.08.123 ↗
54. Additive manufacturing in the spare parts supply chain10.1016/j.compind.2013.07.008 ↗
55. Navy workshop aims to cut costs
56. Frazier, W.E. (2010). Direct digital manufacturing of metallic components: Vision and roadmap. Annu. Int. Solid Free. Fabr. Symp., 717–732.
57. Comparative study of fatigue properties of Ti-6Al-4V specimens built by electron beam melting (EBM) and selective laser melting (SLM)10.1016/j.matchar.2018.03.028 ↗
58. Comparative investigation of small punch creep resistance of Inconel 718 fabricated by selective laser melting10.1016/j.msea.2018.12.083 ↗
59. Parametric analysis of thermal behaviour during selective laser melting Additive manufacturing of Aluminium alloy powder10.1016/j.matdes.2014.07.006 ↗
60. Thermofluid field of molten pool and its effects during selective laser melting (SLM) of Inconel 718 alloy
61. Mills, K.C. (2002). Ni-IN 718, Recommended Values of Thermophysical Properties for Selected Commercial Alloys, Woodhead Publishing.10.1533/9781845690144 ↗
62. Role of oxygen as surface active element in linear GTA welding process10.1007/s11665-013-0621-0 ↗
63. Mills, K.C. (2002). Ti Pure Titanium, Recommended Values of Thermophysical Properties for Selected Commercial Alloys, Woodhead Publishing.10.1533/9781845690144 ↗
64. Research on molten pool temperature in the process of laser rapid forming10.1016/j.jmatprotec.2007.06.090 ↗
65. Griffith, M.L., Keicher, D.M., Atwood, C.L., Romero, J.A., Smugeresky, J.E., Harwell, L.D., and Greene, D.L. (1996, January 12–14). Free Form Fabrication of Metallic Components Using Laser Engineered Net Shaping (LENSTM). In Proceeding of 7th Solid Freeform Fabrication Symposium, Austin, TX, USA.10.2172/425303 ↗
66. Modeling of Transport Phenomena during the Coaxial Laser Direct Deposition Process10.1063/1.3474655 ↗
67. Griffith, M.L., Ensz, M.T., Puskar, J.D., Robino, C.V., Brooks, J.A., Philliber, J.A., Smugeresky, J.E., and Hofmeister, W.H. (2000). Understanding the Microstructure and Properties of Components Fabricated by Laser Engineered Net Shaping (LENS). MRS Proceeding, 625s, Cambridge University Press.10.1557/PROC-625-9 ↗
68. Microstructural Evolution in Laser-Deposited Multilayer Ti-6Al-4V Builds: Part II. Thermal Modeling10.1007/s11661-004-0095-7 ↗
69. Manufacturing Ti-6Al-4V Components by Shaped Metal Deposition: Microstructure and Mechanical Properties10.1088/1757-899X/26/1/012001 ↗
70. Thermal Process Maps for Predicting Solidification Microstructure in Laser Fabrication of Thin-wall Structures10.1016/j.jmatprotec.2006.03.155 ↗
71. Development of egg-configuration heat source model in numerical simulation of autogenous fusion welding process10.1016/j.ijthermalsci.2014.06.032 ↗
72. Analysis of the quality of slope surface in selective laser melting process by simulation and experiments10.1016/j.ijleo.2018.09.049 ↗