Experimental and Numerical Investigation in Directed Energy Deposition for Component Repair
Source abstract
Abstract
Directed energy deposition (DED) has been widely used for component repair. In the repair process, the surface defects are machined to a groove or slot and then refilled. The sidewall inclination angle of the groove geometry has been recognized to have a considerable impact on the mechanical properties of repaired parts. The objective of this work was to investigate the feasibility of repairing various V-shaped defects with both experiments and modeling. At first, the repair volume was defined by scanning the defective zone. Then, the repair volume was sliced to generate the repair toolpath. After that, the DED process was used to deposit Ti6Al4V powder on the damaged plates with two different slot geometries. Mechanical properties of the repaired parts were evaluated by microstructure analysis and tensile test. Testing of the repaired parts showed excellent bonding between the deposits and base materials with the triangular slot repair. 3D finite element analysis (FEA) models based on sequentially coupled thermo-mechanical field analysis were developed to simulate the corresponding repair process. Thermal histories of the substrate on the repair sample were measured to calibrate the 3D coupled thermo-mechanical model. The temperature measurements showed very good verification with the predicted temperature results. After that, the validated model was used to predict the residual stresses and distortions in the parts. Predicted deformation and stress results can guide the evaluation of the repair quality.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical & Aerospace Engineering, Missouri University of Science and Technology, Rolla, MO 65401-0900, USA
Funding
National Science Foundation
References (40)
Show source-provided references
1. Zhang, X., Cui, W., Li, W., and Liou, F. (2019). A hybrid process integrating reverse engineering, pre-repair processing, additive manufacturing, and material testing for component remanufacturing. Materials, 12.10.3390/ma12121961 ↗
2. Laser beam build-up welding: Precision in repair, surface cladding, and direct 3D metal deposition10.1007/s11666-007-9028-5 ↗
3. Rebuilding of metal components with laser cladding forming10.1016/j.apsusc.2005.10.025 ↗
4. Additive manufacturing of a new Fe-Cr-Ni alloy with gradually changing compositions with elemental powder mixes and thermodynamic calculation10.1007/s00170-017-1302-1 ↗
5. Research on the processing experiments of laser metal deposition shaping10.1016/j.optlastec.2005.10.009 ↗
6. Additive manufacturing process selection based on parts’ selection criteria10.1007/s00170-015-7092-4 ↗
7. A review on 3D micro-additive manufacturing technologies10.1007/s00170-012-4605-2 ↗
8. A comparison of the tensile, fatigue, and fracture behavior of Ti-6Al-4V and 15-5 PH stainless steel parts made by selective laser melting10.1007/s00170-013-5106-7 ↗
9. Characteristics of the bond in Cu-H13 tool steel parts fabricated using SLM10.1016/j.cirp.2008.03.010 ↗
10. Enhanced fracture toughness in architected interpenetrating phase composites by 3D printing10.1016/j.compscitech.2018.08.009 ↗
11. Fracture and load-carrying capacity of 3D-printed cracked components10.1016/j.eml.2020.100692 ↗
12. Fatigue behaviour of laser repairing welded joints10.1016/j.engfailanal.2006.11.054 ↗
13. Laser direct manufacturing of tungsten nickel collimation component10.1016/j.jmatprotec.2003.12.009 ↗
14. Mould steels repaired by laser welding10.1016/j.engfailanal.2008.02.010 ↗
15. Hinduja, S., and Fan, K.-C. (2007, January 27). Component repair using laser direct metal deposition BT. Proceedings of the 35th International MATADOR Conference, Taipei, Taiwan.
16. Gupta, K. (2017). Laser-based repair of damaged dies, molds, and gears BT. Advanced Manufacturing Technologies: Modern Machining, Advanced Joining, Sustainable Manufacturing, Springer International Publishing.
17. Laser metal deposition as repair technology for stainless steel and titanium alloys10.1016/j.phpro.2012.10.051 ↗
18. Advances in the modeling of laser direct metal deposition10.2351/1.4815992 ↗
19. Experimental characterization of a direct metal deposited cobalt-based alloy on tool steel for component repair10.1007/s11837-018-3221-5 ↗
20. Stereo vision-based repair of metallic components10.1108/RPJ-09-2015-0118 ↗
21. Laser cladding as repair technology for Ti-6Al-4V alloy: Influence of building strategy on microstructure and hardness10.1016/j.matdes.2015.07.035 ↗
22. Laser engineered net shaping advances additive manufacturing and repair
23. Repair of 304 stainless steel by laser cladding with 316 L stainless steel powders followed by laser surface alloying with WC powders10.1016/j.jmapro.2016.08.004 ↗
24. Cladding of WC-12 Co on low carbon steel using a pulsed Nd:YAG laser10.1016/j.msea.2007.01.132 ↗
25. Damage reconstruction from tri-dexel data for laser-aided repairing of metallic components10.1007/s00170-018-1830-3 ↗
26. Evaluation of component repair using direct metal deposition from scanned data10.1007/s00170-017-1455-y ↗
27. Damage detection and reconstruction algorithm in repairing compressor blade by direct metal deposition10.1007/s00170-017-1413-8 ↗
28. Investigation on Ti6Al4V-V-Cr-Fe-SS316 multi-layers metallic structure fabricated by laser 3D printing10.1038/s41598-017-08580-z ↗
29. Mills, K.C. (2002). Recommended Values of Thermophysical Properties for Selected Commercial Alloys, Woodhead Publishing.10.1533/9781845690144 ↗
30. An experimental-numerical investigation of heat distribution and stress field in single- and multi-track laser cladding by a high-power direct diode laser10.1016/j.optlastec.2014.04.016 ↗
31. Prediction of thermal residual stress and microstructure in direct laser metal deposition via a coupled finite element and multiphase field framework10.1007/s11837-019-03922-w ↗
32. Residual stresses and distortion in additively manufactured compositionally graded and dissimilar joints10.1016/j.commatsci.2017.11.026 ↗
33. Finite element modeling and validation of thermomechanical behavior of Ti-6Al-4V in directed energy deposition additive manufacturing
34. Temperature and residual stress distribution of FGM parts by DED process: Modeling and experimental validation10.1007/s00170-020-05673-4 ↗
35. Deformations and stresses prediction of cantilever structures fabricated by selective laser melting process
36. Incropera, F.P., DeWitt, D.P., Bergman, T.L., and Lavine, A.S. (2006). Introduction to Heat Transfer, John Wiley & Sons.
37. Metal additive-manufacturing process and residual stress modeling10.1186/s40192-016-0047-2 ↗
38. Analytical and numerical modelling of the direct metal deposition laser process10.1088/0022-3727/41/2/025403 ↗
39. A line heat input model for additive manufacturing10.1115/1.4033662 ↗
40. Residual stress and distortion of rectangular and S-shaped Ti-6Al-4V parts by Directed Energy Deposition: Modelling and experimental calibration