Numerical Simulation of Temperature Fields during Laser Welding–Brazing of Al/Ti Plates
Source abstract
Abstract
The formation of dissimilar weld joints, including Al/Ti joints, is an area of research supported by the need for weight reduction and corrosion resistance in automotive, aircraft, aeronautic, and other industries. Depending on the cooling rates and chemical composition, rapid solidification of Al/Ti alloys during laser welding can lead to the development of different metastable phases and the formation of brittle intermetallic compounds (IMCs). The effort to successfully join aluminum to titanium alloys is associated with demands to minimize the thickness of brittle IMC zones by selecting appropriate welding parameters or applying suitable filler materials. The paper is focused on the numerical simulation of the laser welding–brazing of 2.0 mm thick titanium Grade 2 and EN AW5083 aluminum alloy plates using 5087 aluminum filler wire. The developed simulation model was used to study the impact of laser welding–brazing parameters (laser power, welding speed, and laser beam offset) on the transient temperature fields and weld-pool characteristics. The results of numerical simulations were compared with temperatures measured during the laser welding–brazing of Al/Ti plates using a TruDisk 4002 disk laser, and macrostructural and microstructural analyses, and weld tensile strength measurements, were conducted. The ultimate tensile strength (UTS) of welded–brazed joints increases with an increase in the laser beam offset to the Al side and with an increase in welding speed. The highest UTS values at the level of 220 MPa and 245 MPa were measured for joints produced at a laser power of 1.8 kW along with a welding speed of 30 mm·s−1 and a laser beam offset of 300 μm and 460 μm, respectively. When increasing the laser power to 2 kW, the UTS decreased. The results exhibited that the tensile strength of Al/Ti welded–brazed joints was dependent, regardless of the welding parameters, on the amount of melted Ti Grade 2, which, during rapid solidification, determines the thickness and morphology of the IMC layer. A simple formula was proposed to predict the tensile strength of welded–brazed joints using the computed cross-sectional Ti weld metal area.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Materials Science and Technology in Trnava, Slovak University of Technology in Bratislava, Ulica Jána Bottu 2781/25, 917 24 Trnava, Slovakia
Funding
the Scientific Grant Agency (VEGA) of the Ministry of Education, Science, Research and Sport of the Slovak Republic and Slovak Academy of Sciences
References (100+)
Show source-provided references
1. Laser beam welding of Ti/Al dissimilar thin sheets—A literature review
2. Joining of dissimilar materials10.1016/j.cirp.2015.05.006 ↗
3. Laser welding and brazing of dissimilar materials
4. Challenges and advances in laser welding of dissimilar light alloys: Al/Mg, Al/Ti, and Mg/Ti alloys10.1007/s00170-017-1565-6 ↗
5. A review of dissimilar welding for titanium alloys with light alloys10.1051/metal/2021011 ↗
6. A Review: Laser Welding of Dissimilar Materials (Al/Fe, Al/Ti, Al/Cu)—Methods and Techniques, Microstructure and Properties
7. Mathers, G. (2002). The Welding of Aluminium and Its Alloys, CRC Press LLC.10.1201/9781439823224 ↗
8. Leyens, C., and Peters, M. (2006). Titanium and Titanium Alloys: Fundamentals and Applications, John Wiley & Sons.
9. Sánchez Amaya, J.M., Amaya-Vázquez, M.R., and Botana, F.J. (2013). Handbook of Laser Welding Technologies, Woodhead Publishing Ltd.
10. YAG laser offset welding of AA5754 and T40 butt joint10.1016/j.jmatprotec.2015.04.003 ↗
11. Joining mechanism of Ti/Al dissimilar alloys during laser welding-brazing process10.1016/j.jallcom.2010.09.125 ↗
12. Effects of heat input on microstructure and mechanical property of Al/Ti joints by rectangular spot laser welding-brazing method10.1007/s00170-008-1837-2 ↗
13. Combined Laser Beam Welding and Brazing Process for Aluminium Titanium Hybrid Structures10.1016/j.phpro.2011.03.028 ↗
14. Liedl, G., Kratky, A., Mayr, M., and Saliger, A. (2011, January 14–17). Laser assisted joining of dissimilar materials. Proceedings of the IQCMEA-ICF-Processing, Performance and Failure Analysis of Engineering Materials, Luxor, Egypt.
15. Improving interfacial reaction nonhomogeneity during laser welding–brazing aluminum to titanium10.1016/j.matdes.2011.03.074 ↗
16. Aluminum to titanium laser welding-brazing in V-shaped Groove10.1016/j.jmatprotec.2017.02.009 ↗
17. An investigation on butt joints of Ti6Al4V and 5A06 using MIG/TIG double-side arc welding-brazing10.1016/j.jmapro.2017.05.010 ↗
18. Interfacial microstructure and mechanical property of Ti6Al4V/A6061 dissimilar joint by direct laser brazing without filler metal and groove10.1016/j.msea.2012.09.044 ↗
19. Effect of Laser Beam Oscillation on Laser Welding–Brazing of Ti/Al Dissimilar Metals10.3390/ma12244165 ↗
20. Influence of welding parameters on the IMCs and the mechanical properties of Ti/Al butt joints welded by MIG/TIG double-sided arc welding-brazing10.1016/j.jallcom.2018.03.119 ↗
21. Microstructure and tensile properties of Ti/Al dissimilar joint by laser welding-brazing at subatmospheric pressure10.1016/j.jmapro.2019.12.026 ↗
22. Microstructure and tensile properties of dissimilar metal gas tungsten arc welding of aluminium to titanium alloy10.1179/174328409X412014 ↗
23. Tungsten inert gas welding of dissimilar metals aluminum to titanium with aluminum based wire10.1088/2053-1591/ab056f ↗
24. Influence of Welding Heat Input on Microstructure of Ti/Al Joint During Pulsed Gas Metal Arc Welding10.1080/10426914.2014.880464 ↗
25. Mechanisms of joining aluminium A6061-T6 and titanium Ti–6Al–4V alloys by cold metal transfer technology10.1179/1362171813Y.0000000118 ↗
26. Formation of a crack-free joint between Ti alloy and Al alloy by using a high-power CO2 laser10.1023/A:1018620723793 ↗
27. Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V10.1016/j.jmatprotec.2014.10.025 ↗
28. Microstructural Evolution and Characteristics of Weld Fusion Zone in High Speed Dissimilar Welding of Ti and Al10.1007/s12541-015-0274-z ↗
29. Interfacial reaction mode and its influence on tensile strength in laser joining Al alloy to Ti alloy10.1179/174328409X399056 ↗
30. Microstructural behavior on weld fusion zone of Al-Ti and Ti-Al dissimilar lap welding using single-mode fiber laser10.5916/jkosme.2013.37.7.711 ↗
31. Electron beam welding–Techniques and trends–Review10.1016/j.vacuum.2016.05.004 ↗
32. Microstructure and mechanical properties of Al/Ti joints welded by resistance spot welding10.1179/1362171815Y.0000000028 ↗
33. Interlayer growth at interfaces of Ti/Al-1%Mn, Ti/Al-4.6%Mg and Ti/pure Al friction weld joints by post-weld heat treatment10.1179/136217104225021797 ↗
34. Factors dominating joint characteristics in Ti-Al friction welds10.1179/136217102225004185 ↗
35. Friction stir welding of titanium alloy TiAl6V4 to aluminium alloy AA2024-T310.1016/j.msea.2009.07.006 ↗
36. Interface characteristic of friction stir welding lap joints of Ti/Al dissimilar alloys10.1016/S1003-6326(11)61174-6 ↗
37. Influence of probe offset distance on interfacial microstructure and mechanical properties of friction stir butt welded joint of Ti6Al4V and A6061 dissimilar alloys10.1016/j.matdes.2013.12.040 ↗
38. Microstructural characterization and mechanical properties in friction stir welding of aluminum and titanium dissimilar alloys10.1016/j.matdes.2008.06.008 ↗
39. Study on the Joining of Titanium and Aluminum Dissimilar Alloys by Friction Stir Welding10.2174/1874088X01105010256 ↗
40. Formation of structural and mechanical inhomogeneities in explosion welding of aluminum to titanium10.1080/09507116.2013.796663 ↗
41. Microstructure and mechanical properties of Ti/Al explosive cladding10.1016/j.matdes.2013.12.012 ↗
42. Microstructure Changes and Phase Growth Occurring at the Interface of the Al/Ti Explosively Welded and Annealed Joints10.1007/s11665-016-1978-7 ↗
43. Low cycle fatigue properties of AA2519–Ti6Al4V laminate bonded by explosion welding10.1016/j.engfailanal.2016.01.001 ↗
44. Microstructure characteristics in the interface zone of Ti/Al diffusion bonding10.1016/S0167-577X(02)00570-0 ↗
45. Effect of Diffusion Bonding Temperature on Mechanical and Microstructure Characteristics of Cp Titanium and High Strength Aluminium Dissimilar Joints10.4028/www.scientific.net/AMM.787.495 ↗
46. Diffusion bonding of titanium and AA 7075 aluminum alloy dissimilar joints—Process modeling and optimization using desirability approach10.1007/s00170-015-8223-7 ↗
47. Solid state joining of aluminum, titanium and their hybrids by ultrasonic torsion welding10.1002/mawe.201400355 ↗
48. Microstructural characterization and mechanical properties of high power ultrasonic spot welded aluminum alloy AA6111–TiAl6V4 dissimilar joints10.1016/j.matchar.2014.09.001 ↗
49. Solid state joining of aluminium to titanium by high power ultrasonics10.4028/www.scientific.net/MSF.794-796.345 ↗
50. Zhang, C. (2015). Ultrasonic Welding of Aluminium to Titanium: Microstructure, Properties, and Alloying Effects. [PhD Thesis, The University of Manchester]. Available online: https://www.escholar.manchester.ac.uk/api/datastream?publicationPid=uk-ac-man-scw:270275&datastreamId=FULL-TEXT.PDF.
51. Investigation on TIG arc welding-brazing of Ti/Al dissimilar alloys with Al based fillers10.1179/1362171812Y.0000000041 ↗
52. The microstructure and mechanical properties of fluxless gas tungsten arc welding–brazing joints made between titanium and aluminum alloys10.1016/j.matdes.2012.09.007 ↗
53. Interfacial Microstructural Characterization of Ti/Al Joints by Gas Tungsten Arc Welding10.1080/10426914.2013.864414 ↗
54. Microstructure and Tensile Behavior of Laser Arc Hybrid Welded Dissimilar Al and Ti Alloys10.3390/ma7031590 ↗
55. Microstructure and mechanical properties of ultrasonic spot welded Al/Ti alloy joints10.1016/j.matdes.2015.04.023 ↗
56. Interfacial reaction of intermetallic compounds of ultrasonic-assisted brazed joints between dissimilar alloys of Ti-6Al-4V and Al-4Cu-1Mg10.1016/j.ultsonch.2011.03.025 ↗
57. Ultrasonic-assisted brazing of Al–Ti dissimilar alloy by a filler metal with a large semi-solid temperature range10.1016/j.matdes.2016.01.109 ↗
58. Numerical simulation of the laser welding process in butt-joint specimens10.1016/S0924-0136(02)00921-4 ↗
59. Kik, T. (2020). Computational Techniques in Numerical Simulations of Arc and Laser Welding Processes. Materials, 13.10.3390/ma13030608 ↗
60. Thermal modelling of laser welding and related processes a literature review10.1016/j.optlastec.2004.02.017 ↗
61. Numerical modelling of welding10.1016/j.cma.2005.08.018 ↗
62. Mathematical Modeling of Weld Phenomena, Part 1: Finite-Element Modeling
63. Modeling and experimental analysis of fiber laser offset welding of Al-Ti butt joints10.1007/s00170-015-7562-8 ↗
64. FEM analysis of fiber laser welding of Titanium and Aluminum10.1016/j.procir.2016.01.030 ↗
65. FEM Simulation of Dissimilar Aluminum Titanium Fiber Laser Welding Using 2D and 3D Gaussian Heat Sources10.3390/met7080307 ↗
66. Design of Laser Welding Parameters for Joining Ti Grade 2 and AW 5754 Aluminium Alloys Using Numerical Simulation
67. Prediction of temperature fields during laser welding of Al-Ti sheets using numerical simulation
68. Simulation model of Al-Ti dissimilar laser welding-brazing and its experimental verification10.1088/1757-899X/179/1/012007 ↗
69. Temperature field simulation and grain morphology on laser welding-brazing between Ti-6Al-4V and 1050 aluminum alloy10.1088/2053-1591/ab061a ↗
70. Microstructure and mechanical characterization of re-melted Ti-6Al-4V and Al-Mg-Si alloys butt weld10.1016/j.vacuum.2018.04.048 ↗
71. Numerical and experimental investigation of thermal stress distribution in laser lap welding of Ti6Al4V and 2024 alloy plates10.1007/s00170-021-08019-w ↗
72. Numerical simulation of the temperature field, weld profile, and weld pool dynamics in laser welding of aluminium alloy10.1016/j.ijleo.2021.167990 ↗
73. Influence of scan paths on flow dynamics and weld formations during oscillating laser welding of 5A06 aluminum alloy10.1016/j.jmrt.2020.12.102 ↗
74. Numerical Simulations and Experimental Validation on LBW Bead Profiles of Ti-6Al-4V Alloy10.47836/pjst.29.3.32 ↗
75. The prediction of the whole weld in fiber laser keyhole welding based on numerical simulation10.1016/j.applthermaleng.2016.11.050 ↗
76. Numerical simulation of molten pool dynamics in high power disk laser welding10.1016/j.jmatprotec.2011.09.011 ↗
77. A three-dimensional numerical simulation model for weld characteristics analysis in fiber laser keyhole welding10.1016/j.ijheatmasstransfer.2016.12.034 ↗
78. Buttazzoni, M., Zenz, C., Otto, A., Gómez Vázquez, R., Liedl, G., and Arias, J.L. (2021). A Numerical Investigation of Laser Beam Welding of Stainless Steel Sheets with a Gap. Appl. Sci, 11.10.20944/preprints202102.0533.v1 ↗
79. The analysis of asymmetry characteristics during the fiber laser welding of dissimilar materials by numerical simulation10.1007/s00170-021-08312-8 ↗
80. Numerical simulation of alloy composition in dissimilar laser welding10.1016/j.jmatprotec.2015.05.005 ↗
81. Numerical analysis of intermetallic compounds formed during laser welding of Aluminum-Magnesium dissimilar couple10.1016/j.tsep.2020.100838 ↗
82. Laser conduction welding characteristics of dissimilar metals Mg/Ti with Al interlayer10.1016/j.jmapro.2018.03.019 ↗
83. Numerical modeling of fluid flow, heat, and mass transfer for similar and dissimilar laser welding of Ti-6Al-4V and Inconel 71810.1007/s00170-021-06868-z ↗
84. Ghosh, P.S., Sen, A., Chattopadhyaya, S., Sharma, S., Singh, J., Dwivedi, S.P., Saxena, A., Khan, A.M., Pimenov, D.Y., and Giasin, K. (2021). Prediction of Transient Temperature Distributions for Laser Welding of Dissimilar Metals. Appl. Sci., 11.10.3390/app11135829 ↗
85. Numerical study on molten pool dynamics and solute distribution in laser deep penetration welding of steel and aluminum10.1016/j.optlastec.2021.107085 ↗
86. Prediction of weld geometry, temperature contour and strain distribution in disk laser welding of dissimilar joining between copper & 304 stainless steel10.1016/j.ijleo.2020.165288 ↗
87. Investigation of metal mixing in laser keyhole welding of dissimilar metals10.1016/j.matdes.2020.109056 ↗
88. Butt laser welding-brazing of AZ31Mg alloy to Cu coated Ti-6Al-4V with AZ92 Mg based filler10.1016/j.optlastec.2019.04.024 ↗
89. A Review on Melt-Pool Characteristics in Laser Welding of Metals10.1155/2018/4920718 ↗
90. Zhou, X., Duan, J., Zhang, F., and Zhong, S. (2019). The study on mechanical strength of titanium-aluminum dissimilar butt joints by laser welding-brazing process. Materials, 12.10.3390/ma12050712 ↗
91. Jandaghi, M.R., Saboori, A., Khalaj, G., and Khanzadeh Ghareh Shiran, M. (2020). Microstructural Evolutions and its Impact on the Corrosion Behaviour of Explosively Welded Al/Cu Bimetal. Metals, 10.10.3390/met10050634 ↗
92. Effect of stand-off distance on the mechanical and metallurgical properties of explosively bonded 321 austenitic stainless steel-1230 aluminum alloy tubes10.1590/1980-5373-mr-2016-0516 ↗
93. Nagy, M. (2020). Influence of technological parameters of laser welding on the microstructure and properties of aluminium and titanium weld joints. [PhD Thesis, Slovak University of Technology in Bratislava, MTF in Trnava].
94. A Review on Process Parameters of Ti/Al Dissimilar Joint Using Laser Beam Welding
95. Finite element modelling and simulation of welding. Part 1: Increasing complexity10.1080/01495730150500442 ↗
96. Incropera, P.F., and De Witt, D.P. (1996). Fundamentals of Heat and Mass Transfer, J. Wiley and Sons.
97. Disk laser weld brazing of AW5083 aluminium alloy with titanium Grade 210.1007/s11665-017-2529-6 ↗
98. (2022, December 06). Ansys® Academic Research Mechanical, Release 18.2. Available online: https://www.ansys.com/academic/terms-and-conditions.
99. (2022, December 06). JMatPro Help, Release 6.1, Sente Software Ltd, Available online: https://www.crz.gov.sk/data/att/265769_dokument1.PDF.
100. Mathematical modelling of solidification and melting: A review, Modelling Simul