journal article·2023-03-29Open access

On the Role of Microstructure and Defects in the Room and High-Temperature Tensile Behavior of the PBF-LB A357 (AlSi7Mg) Alloy in As-Built and Peak-Aged Conditions

Lavinia Tonelli, Erica Liverani, Gianluca Di Egidio, Alessandro Fortunato, Alessandro Morri, Lorella Ceschini

Materials· Volume 16· Issue 7

Abstract

Additive processes like Laser Beam Powder Bed Fusion (PBF-LB) result in a distinctive microstructure characterized by metastability, supersaturation, and finesse. Post-process heat treatments modify microstructural features and tune mechanical behavior. However, the exposition at high temperatures can induce changes in the microstructure. Therefore, the present work focuses on the analyses of the tensile response at room and high (200 °C) temperature of the A357 (AlSi7Mg0.6) alloy processed by PBF-LB and subjected to tailored T5 (direct aging) and T6R (rapid solution treatment, quenching, and aging) treatments. Along with the effect of microstructural features in the as-built T5 and T6R alloy, the role of typical process-related defects is also considered. In this view, the structural integrity of the alloy is evaluated by a deep analysis of the work-hardening behavior, and quality indexes have been compared. Results show that T5 increases tensile strength at room temperature without compromising ductility. T6R homogenizes the microstructure and enhances the structural integrity by reducing the detrimental effect of defects, resulting in the best trade-off between strength and ductility. At 200 °C, tensile properties are comparable, but if resilience and toughness moduli are considered, as-built and T5 alloys show the best overall mechanical performance.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Industrial Engineering (DIN), Alma Mater Studiorum—University of Bologna, Viale del Risorgimento 2, 40136 Bologna, Italy

Funding

European Union-NextGenerationEU · Italian Ministry of University · National Recovery and Resilience Plan (NRRP)

References (65)

Show source-provided references
1. Anderson, K., Weritz, J., and Kaufman, J.G. (2018). Aluminum Science and Technology, ASM International.10.31399/asm.hb.v02a.9781627082075 ↗
2. Anderson, K., Weritz, J., and Kaufman, J.G. (2019). Properties and Selection of Aluminum Alloys, ASM International.10.31399/asm.hb.v02b.9781627082105 ↗
3. Room and high temperature fatigue behaviour of the A354 and C355 (Al-Si-Cu-Mg) alloys: Role of microstructure and heat treatment10.1016/j.msea.2015.12.015 ↗
4. Totten, G.E. (2016). Heat Treating of Nonferrous Alloys, ASM International.10.31399/asm.hb.v04e.9781627081696 ↗
5. Effect of Cu addition on overaging behaviour, room and high temperature tensile and fatigue properties of A357 alloy10.1016/S1003-6326(20)65427-9 ↗
6. Research status of laser additive manufacturing for metal: A review10.1016/j.jmrt.2021.08.050 ↗
7. A review of Laser Powder Bed Fusion Additive Manufacturing of aluminium alloys: Microstructure and properties
8. A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends10.1016/j.jmst.2018.09.004 ↗
9. Review on the correlation between microstructure and mechanical performance for laser powder bed fusion AlSi10Mg
10. Study of AlSi7Mg0.6 Alloy by Selective Laser Melting: Mechanical Properties, Microstructure, Heat Treatment
11. Casati, R., Nasab, M.H., Tirelli, V., and Vedani, M. (2018, January 14–18). Effect of different heat treatment routes on microstructure and mechanical properties of AlSi7Mg, AlSi10Mg and Al-Mg-Zr-Sc alloys produced by selective laser melting. Proceedings of the European Congress and Exhibition on Powder Metallurgy, European PM Conference Proceedings, Bilbao, Spain.
12. Aging Response of an A357 Al Alloy Processed by Selective Laser Melting10.1002/adem.201800406 ↗
13. Selective laser melted Al-7Si-0.6Mg alloy with in-situ precipitation via platform heating for residual strain removal10.1016/j.matdes.2019.108005 ↗
14. Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions10.1016/j.msea.2020.139124 ↗
15. Effect of build orientation on fracture and tensile behavior of A357 Al alloy processed by Selective Laser Melting10.1016/j.msea.2019.138392 ↗
16. Trevisan, F., Calignano, F., Lorusso, M., Pakkanen, J., Ambrosio, E.P., Lombardi, M., Pavese, M., Manfredi, D., and Fino, P. (2016, January 9–13). Effects of Heat Treatments on A357 Alloy Produced by Selective Laser Melting. Proceedings of the European Congress and Exhibition on Powder Metallurgy, European PM Conference Proceedings, Hamburg, Germany.
17. A Novel T6 Rapid Heat Treatment for AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion: Comparison with T5 and Conventional T6 Heat Treatments10.1007/s11663-021-02365-6 ↗
18. Defects and anomalies in powder bed fusion metal additive manufacturing10.1016/j.cossms.2021.100974 ↗
19. Defect-Correlated Vickers Microhardness of Al-Si-Mg Alloy Manufactured by Laser Powder Bed Fusion with Post-process Heat Treatments10.1007/s11665-022-06874-6 ↗
20. Effect of hot isostatic pressing on the critical defect size distribution in AlSi7Mg0.6 alloy obtained by selective laser melting10.1016/j.ijfatigue.2020.105797 ↗
21. Lehmhus, D., Rahn, T., Struss, A., Gromzig, P., Wischeropp, T., and Becker, H. (2022). High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing. Materials, 15.10.3390/ma15207386 ↗
22. Study of High Temperature Properties of AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion10.4028/www.scientific.net/MSF.1016.1485 ↗
23. Di Egidio, G., Morri, A., and Ceschini, L. (2022, January 18–19). Evaluation of High-temperature tensile properties of heat-treated AlSi10Mg alloy produced by Laser-Based Powder Bed Fusion. Proceedings of the 31st International Conference on Metallurgy and Materials, Brno, Czech Republic.10.37904/metal.2022.4433 ↗
24. Di Egidio, G., Morri, A., Ceschini, L., and Tonelli, L. (2023). High-Temperature Behavior of the Heat-Treated and Overaged AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion and Comparison with Conventional Al–Si–Mg-Casting Alloys. Adv. Eng. Mater., 2201238.10.1002/adem.202201238 ↗
25. Role of direct aging and solution treatment on hardness, microstructure and residual stress of the A357 (AlSi7Mg0.6) alloy produced by powder bed fusion10.1007/s11663-021-02179-6 ↗
26. (2005). Aluminium and Aluminium Alloys—Designation of Alloyed Aluminium Ingots for Remelting, Master Alloys and Castings–Part 1: Numerical Designation System (Standard No. DS/EN 1780-1:2005).
27. Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting10.1007/s00170-019-04641-x ↗
28. (2020). Aluminium and Aluminium Alloys—Castings—Chemical Composition and Mechanical Properties (Standard No. EN 1706:2020).
29. (2020, September 15). Carpenter Technology. (n.d.). Available online: www.carpenteradditive.com.
30. (2019). Metallic Materials—Tensile testing, Method of Test at Room Temperature (Standard No. ISO 6892-1).
31. Kaufman, J.G. (2000). Introduction to Aluminum Alloys and Tempers, ASM International.
32. (2019). Metallic Materials—Tensile Testing, Method of Test at Elevated Temperature (Standard No. ISO 6892-2).
33. Kuhn, H., and Medlin, D. (2000). Mechanical Testing and Evaluation in ASM Handbook, ASM International.10.31399/asm.hb.v08.9781627081764 ↗
34. Dieter, G.E., and Bacon, D.J. (1986). Mechanical Metallurgy, McGraw-Hill.
35. Angella, G., and Zanardi, F. (2019). Validation of a New Quality Assessment Procedure for Ductile Irons Production Based on Strain Hardening Analysis. Metals, 9.10.3390/met9080837 ↗
36. Evaluating structural integrity of cast Al-7%Si-Mg alloys via work hardening characteristics—II. A new quality index10.1016/j.msea.2003.10.310 ↗
37. Evaluating structural integrity of cast Al-7%Si-Mg alloys via work hardening characteristics—1. Concept of target properties10.1016/j.msea.2003.10.311 ↗
38. A rationale for the quality index of Al-Si-Mg casting alloys10.1080/13640461.2000.11819376 ↗
39. On the significance to use dislocation-density-related constitutive equations to correlate strain hardening with microstructure of metallic alloys: The case of conventional and austempered ductile irons10.1016/j.jallcom.2016.01.233 ↗
40. (2020). Metallic Materials—Sheet and Strip—Determination of Tensile Strain Hardening Exponent (Standard No. ISO 10275:2020).
41. (2018). Standard Test Method for Brinell Hardness of Metallic Materials (Standard No. ASTM E10-18).
42. (2017). Standard Guide for Preparation of Metallographic Specimens (Standard No. ASTM E3-11(2017)).
43. Voort, G.V. (2004). Metallography and Microstructures in ASM Handbook, ASM International.
44. Rueden, C.T., Schindelin, J., Hiner, M.C., DeZonia, B.E., Walter, A.E., Arena, E.T., and Eliceiri, K.W. (2017). ImageJ2: ImageJ for the next generation of scientific image data. BMC Bioinform., 18.10.1186/s12859-017-1934-z ↗
45. Van Cauwenbergh, P., Beckers, A., Thijs, L., Van Hooreweder, B., and Vanmeensel, K. (2018, January 14–18). Heat treatment optimization via thermo-physical characterization of AlSi7Mg and AlSi10Mg manufactured by laser powder bed fusion (LPBF). Proceedings of the European Congress and Exhibition on Powder Metallurgy, European PM Conference Proceedings, Bilbao, Spain.
46. Casati, R., Hamidi, M.N., Coduri, M., Tirelli, V., and Vedani, M. (2018). Effects of Platform Pre-Heating and Thermal-Treatment Strategies on Properties of AlSi10Mg Alloy Processed by Selective Laser Melting. Metals, 8.10.3390/met8110954 ↗
47. Strength and strain hardening of a selective laser melted AlSi10Mg alloy10.1016/j.scriptamat.2017.07.025 ↗
48. Influence of sub-cell structure on the mechanical properties of AlSi10Mg manufactured by laser powder bed fusion10.1016/j.msea.2020.138976 ↗
49. Influence of Si precipitates on fracture mechanisms of AlSi10Mg parts processed by Selective Laser Melting10.1016/j.actamat.2019.06.013 ↗
50. Strengthening mechanisms in direct metal laser sintered AlSi10Mg: Comparison between virgin and recycled powders
51. Microstructure evolution and mechanical properties at high temperature of selective laser melted AlSi10Mg10.1016/j.jmst.2020.04.066 ↗
52. Evaluation by nanoindentation of the influence of heat treatments and the consequent induced microstructure on the mechanical response of the heat-treated L-PBF AlSi10Mg alloy
53. Selective laser melting of aluminum alloys10.1557/mrs.2017.63 ↗
54. Novel approach based on tensile strain hardening analysis to assess the integrity of an Al alloy produced through High-Pressure Die Casting
55. Physics and phenomenology of strain hardening: The FCC case10.1016/S0079-6425(02)00003-8 ↗
56. Constitutive equations optimized for determining strengths of metallic alloys10.1016/j.mechmat.2014.01.010 ↗
57. Tensile flow and work hardening behavior of hot cross-rolled AA7010 aluminum alloy sheets10.1016/j.msea.2013.03.079 ↗
58. A Review of the Stages of Work Hardening10.4028/www.scientific.net/SSP.35-36.1 ↗
59. Stress–strain curves of metallic materials and post-necking strain hardening characterization: A review10.1111/ffe.13134 ↗
60. Revisiting the Considère criterion from the viewpoint of dislocation theory fundamentals10.1016/j.scriptamat.2013.12.009 ↗
61. Morales-Palma, D., Martínez-Donaire, A.J., and Vallellano, C. (2017). On the Use of Maximum Force Criteria to Predict Localised Necking in Metal Sheets under Stretch-Bending. Metals, 7.10.3390/met7110469 ↗
62. Kuhn, H., and Medlin, D. (2000). Mechanical Testing and Evaluation, ASM International.10.31399/asm.hb.v08.9781627081764 ↗
63. Di Egidio, G., Martini, C., Börjesson, J., Ghassemali, E., Ceschini, L., and Morri, A. (2023). Influence of Microstructure on Fracture Mechanisms of the Heat-Treated AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion. Materials, 16.10.3390/ma16052006 ↗
64. Role of Melt pool boundary condition in dertermining the mechanical properties of selective laser melting AlSi10Mg alloy10.1016/j.msea.2018.10.083 ↗
65. Fracture resistance of AlSi10Mg fabricated by laser powder bed fusion10.1016/j.actamat.2021.116869 ↗