journal article·2025-01-16Open access

Development of Tailored Porous Ti6Al4V Materials by Extrusion 3D Printing

Luis Olmos, Ana Silvia González-Pedraza, Héctor Javier Vergara-Hernández, Didier Bouvard, Monserrat Sofía López-Cornejo, Rumualdo Servín-Castañeda

Materials· Volume 18· Issue 2

Abstract

Nowadays, metallic bone replacement is in high demand due to different issues, like sicknesses and accidents. Thus, bone implants are fabricated with tailored properties and microstructure for long-term use in the human body. To improve such implants, 3D printing is the most promising technique. Therefore, this work aims to evaluate the fabrication of porous materials by extrusion 3D printing of Ti6Al4V. Cylindrical samples were fabricated from pellets for metal injection molding of Ti6Al4V powders, creating hexagonal channels with three different sizes. The densification kinetics was evaluated by dilatometry tests, which enabled following the densification of the samples during the sintering cycle. Subsequently, the samples were characterized by scanning electron microscopy and X-ray computed tomography to analyze their microstructure. Compression tests evaluated the mechanical strength of sintered samples. It was found that the hexagonal shape during printing is better defined as the channel size increases. The results show similar behavior for each of the channel sizes during sintering; however, greater densification is obtained as the channel size decreases. Additionally, microporosity is obtained at the particle level, which is completely interconnected, ensuring the passage of fluids through the entire sample. On the other hand, as the channel size increases, Young’s modulus and yield strength are considerably reduced. The main conclusion is that parts with two scales of porosity can be designed by the 3D printing extrusion process.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Bone Tissue Engineering Materials · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Universidad Michoacana de San Nicolás de Hidalgo, INICIT, Fco. J. Mujica S/N, Morelia 58060, Michoacán, Mexico

División de Estudios de Posgrado e Investigación, Tecnológico Nacional de México/I.T. Morelia, Av. Tecnológico #1500, Colonia Lomas de Santiaguito, Morelia 58120, Michoacán, Mexico

University Grenoble Alpes, CNRS, SIMAP, 38000 Grenoble, France

Universidad Autónoma de Coahuila, Facultad de Ingeniería Mecánica y Eléctrica Unidad Norte, Monclova 25720, Coahuila, Mexico

Funding

National Council of Humanities, Science and Technology CONAHCYT

References (72)

Show source-provided references
1. Lutzweiler, G., Ndreu Halili, A., and Engin Vrana, N. (2020). The overview of porous, bioactive scaffolds as instructive biomaterials for tissue regeneration and their clinical translation. Pharmaceutics, 12.10.3390/pharmaceutics12070602 ↗
2. The select of internal architecture for porous Ti alloy scaffold: A compromise between mechanical properties and permeability10.1016/j.matdes.2020.108754 ↗
3. Fermenia, J.L., and Borrás, V.A. (2023). Desarrollo de Aleaciones de Titanio: Implicaciones en el Sector Biomédico Europeo, Universitat Politecnica de Valencia.
4. Antunes, L.H.M., and De Lima, C.R.P. (2018). Cobalt-Chromium Alloys—Properties and Applications. Reference Module in Materials Science and Materials Engineering, Elsevier.10.1016/B978-0-12-803581-8.09386-3 ↗
5. Ali, S., Irfan, M., Niazi, U.M., Rani, A.M.A., Rashedi, A., Rahman, S., Khan, M.K.A., Alsaiari, M.A., Legutko, S., and Petrů, J. (2022). Microstructure and Mechanical Properties of Modified 316L Stainless Steel Alloy for Biomedical Applications Using Powder Metallurgy. Materials, 15.10.3390/ma15082822 ↗
6. Adamovic, D., Ristic, B., and Zivic, F. (2018). Review of existing biomaterials—Method of material selection for specific applications in orthopedics. Biomaterials in Clinical Practice: Advances in Clinical Research and Medical Devices, Springer Nature.10.1007/978-3-319-68025-5_3 ↗
7. Novel Method for the Production of Titanium Foams to Reduce Stress Shielding in Implants10.1021/acsomega.2c02340 ↗
8. Alkentar, R., Kladovasilakis, N., Tzetzis, D., and Mankovits, T. (2023). Effects of pore size parameters of titanium additively manufactured lattice structures on the osseointegration process in orthopedic applications: A comprehensive review. Crystals, 13.10.3390/cryst13010113 ↗
9. A Review of Different Manufacturing Methods of Metallic Foams10.1021/acsomega.3c08613 ↗
10. Olmos, L., González-Pedraza, A.S., Vergara-Hernández, H.J., Chávez, J., Jiménez, O., Mihalcea, E., Arteaga, D., and Ruiz-Mondragón, J.J. (2022). Ti64/20Ag Porous Composites Fabricated by Powder Metallurgy for Biomedical Applications. Materials, 15.10.3390/ma15175956 ↗
11. Fabrication and characterization of highly porous Ti6Al4V/xTa composites for orthopedic applications10.1007/s10853-020-05166-5 ↗
12. Improving mechanical properties and antibacterial response of α/β ternary Ti–Ta alloy foams for biomedical uses10.1016/j.jmrt.2023.05.115 ↗
13. Karakurt, E.M., Cetin, Y., Incesu, A., Demirtas, H., Kaya, M., Yildizhan, Y., Tosun, M., and Huang, Y. (2023). Microstructural, Biomechanical, and In Vitro Studies of Ti-Nb-Zr Alloys Fabricated by Powder Metallurgy. Materials, 16.10.3390/ma16124240 ↗
14. The development of porous metallic materials: A short review of fabrication, characteristics, and applications10.1088/1402-4896/ad086c ↗
15. Design and additive manufacturing of porous titanium scaffolds for optimum cell viability in bone tissue engineering10.1177/0954405420937565 ↗
16. Hydromechanical mechanism behind the effect of pore size of porous titanium scaffolds on osteoblast response and bone ingrowth10.1016/j.matdes.2019.108151 ↗
17. Influence of the pore size and porosity of selective laser melted Ti6Al4V ELI porous scaffold on cell proliferation, osteogenesis and bone ingrowth10.1016/j.msec.2019.110289 ↗
18. Rugosidad óptima de un implante para generar la osteointegración y la fijación biológica10.15417/issn.1852-7434.2024.89.5.1930 ↗
19. Osseointegration of functionally graded Ti6Al4V porous implants: Histology of the pore network10.1016/j.bioadv.2023.213697 ↗
20. Bond and fracture strength of metal-ceramic restorations formed by selective laser sintering10.4047/jap.2014.6.4.266 ↗
21. Osteogenesis of adipose-derived stem cells on polycaprolactone–β-tricalcium phosphate scaffold fabricated via selective laser sintering and surface coating with collagen type I10.1002/term.1811 ↗
22. Selective laser sintering in biomedical engineering10.1007/s11517-012-1001-x ↗
23. 3D printing in medicine for preoperative surgical planning: A review10.1007/s10439-019-02411-0 ↗
24. Three-dimensional (3D) printed scaffold and material selection for bone repair10.1016/j.actbio.2018.11.039 ↗
25. A review on stereolithography and its applications in biomedical engineering10.1016/j.biomaterials.2010.04.050 ↗
26. Influence of layer thickness and raster angle on the mechanical properties of 3D-printed PEEK and a comparative mechanical study between PEEK and ABS10.3390/ma8095271 ↗
27. Extrusion-based 3D printed biodegradable porous iron10.1016/j.actbio.2020.11.022 ↗
28. Fabrication and evaluation of 3D printed BCP scaffolds reinforced with ZrO2 for bone tissue applications10.1002/bit.26514 ↗
29. Fatigue behaviour of titanium scaffolds with hierarchical porosity produced by material extrusion additive manufacturing10.1016/j.matdes.2022.111453 ↗
30. Sinter-Based Additive Manufacturing of Graded Porous Titanium Scaffolds by Multi-Inks 3D Extrusion10.1002/adem.202201159 ↗
31. Fabricating lattice structures via 3D printing: The case of porous bio-engineered scaffolds10.3390/applmech2020018 ↗
32. Kantaros, A. (2022). 3D printing in regenerative medicine: Technologies and resources utilized. Int. J. Mol. Sci., 23.10.3390/ijms232314621 ↗
33. Tang, G., Liu, Z., Liu, Y., Yu, J., Wang, X., Tan, Z., and Ye, X. (2021). Recent trends in the development of bone regenerative biomaterials. Front. Cell Dev. Biol., 9.10.3389/fcell.2021.665813 ↗
34. Review on porous scaffolds generation process: A tissue engineering approach10.1021/acsabm.2c00740 ↗
35. Doryab, A., and Schmid, O. (2022). Bioactive cell-derived ECM scaffold forms a unique cellular microenvironment for lung tissue engineering. Biomedicines, 10.10.3390/biomedicines10081791 ↗
36. A bioinspired 3D shape olibanum-collagen-gelatin scaffolds with tunable porous microstructure for efficient neural tissue regeneration10.1002/btpr.2918 ↗
37. Scaffold Mean Pore Size Influences Mesenchymal Stem Cell Chondrogenic Dierentiation and Matrix Deposition10.1089/ten.tea.2013.0545 ↗
38. Salt fusion: An approach to improve pore interconnectivity within tissue engineering scaffolds10.1089/107632702753503045 ↗
39. Copper extrusion 3D printing using metal injection moulding feedstock: Analysis of process parameters for green density and surface roughness optimization
40. Additive manufacturing of 17–4 PH steel using metal injection molding feedstock: Analysis of 3D extrusion printing, debinding and sintering
41. Copper additive manufacturing using MIM feedstock: Adjustment of printing, debinding, and sintering parameters for processing dense and defectless parts10.1007/s00170-021-07188-y ↗
42. Overview of debinding methods for parts manufactured using powder material extrusion
43. Study of solvent debinding parameters for metal injection moulded 316L stainless steel10.1088/1757-899X/257/1/012035 ↗
44. González-Pedraza, A.S., Bouvard, D., Missiaen, J.M., Olmos, L., Vergara-Hernández, H.J., Lemus-Ruiz, J., and Villalobos, J.C. (2024). Analyzing the Debinding Step of Ti64 Parts Fabricated by 3D Printing Extrusion. Coatings, 14.10.3390/coatings14060715 ↗
45. German, R.M. (1996). Sintering Theory and Practice, John Willey & Sons.
46. Preparation, characterization and designing of porous Ti–6Al–4V through metal injection molding without space holder10.1016/j.jmrt.2023.10.269 ↗
47. Sintering study of Ti6Al4V powders with different particle sizes and their mechanical properties10.1007/s12613-018-1693-5 ↗
48. Analysing the sintering of heterogeneous powder structures by in situ microtomography10.1080/14786430903150225 ↗
49. Analysis of compression and permeability behavior of porous Ti6Al4V by computed microtomography10.1007/s12540-018-00223-w ↗
50. Optimal X-ray micro-CT image based methods for porosity and permeability quantification in heterogeneous sandstones10.1093/gji/ggaa321 ↗
51. (2020). Standard Test Method for Compressive Properties of Rigid Plastics (Standard No. ASTM D695-02).
52. Evaluation of channel-like porous-structured titanium in mechanical properties and osseointegration10.1016/j.jmst.2019.10.026 ↗
53. 3D-printing porosity: A new approach to creating elevated porosity materials and structures10.1016/j.actbio.2018.03.039 ↗
54. Material extrusion additive manufacturing of Ti6Al4V bio-inspired bone implants with tunable Young’s modulus
55. Effects of porosity distribution on mechanical properties and osseointegration of porous polyetheretherketone10.1016/j.bioadv.2024.214043 ↗
56. Evaluation of biocompatibility and osseointegration of multi-component TiAl6V4 titanium alloy implants10.1002/jor.25974 ↗
57. Beyond Kozeny–Carman: Predicting the permeability in porous media10.1007/s11242-019-01321-y ↗
58. Quantitative prediction of permeability in porous rock10.1103/PhysRevB.34.8179 ↗
59. Measurements of permeability in human calcaneal trabecular bone10.1016/S0021-9290(97)00016-X ↗
60. Chao, L., He, Y., Gu, J., Xie, D., Yang, Y., Shen, L., Wu, G., Wang, L., and Tian, Z. (2023). Evaluation of compressive and permeability behaviors of trabecular-like porous structure with mixed porosity based on mechanical topology. J. Funct. Biomater., 14.10.3390/jfb14010028 ↗
61. Differential effects of designed scaffold permeability on chondrogenesis by chondrocytes and bone marrow stromal cells10.1016/j.biomaterials.2009.09.041 ↗
62. Young’s modulus of trabecular bone at the tissue level: A review10.1016/j.actbio.2018.08.001 ↗
63. Biomimetic design strategy of complex porous structure based on 3D printing Ti-6Al-4V scaffolds for enhanced osseointegration10.1016/j.matdes.2022.110721 ↗
64. Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: A review10.1016/j.biomaterials.2016.01.012 ↗
65. Understanding the superior mechanical properties of hollow-strut metal lattice materials10.1016/j.scriptamat.2023.115341 ↗
66. Geometrical parameters and mechanical properties of Ti6Al4V hollow-walled lattices10.1016/j.msea.2022.142667 ↗
67. Node-reinforced hollow-strut metal lattice materials for higher strength10.1016/j.scriptamat.2023.115547 ↗
68. Ti–6Al–4V hybrid-strut lattice metamaterials: A design strategy for improved performance10.1016/j.msea.2024.146918 ↗
69. Manufacturability of Ti-Al-4V hollow-walled lattice struts by laser powder bed fusion10.1007/s11837-021-04914-5 ↗
70. Ti-6Al-4V hollow-strut lattice materials by laser powder bed fusion
71. Bamboo-inspired, simulation-guided design and 3D printing of light-weight and high-strength mechanical metamaterials10.1016/j.apmt.2021.101268 ↗
72. Gibson, L.J., and Ashby, M.F. (1999). Cellular Solids: Structure and Properties, Cambridge University Press. [2nd ed.].