journal article·2023-06-11Open access

Abrasive Wear Resistance of Ultrafine Ausferritic Ductile Iron Intended for the Manufacture of Gears for Mining Machinery

Dawid Myszka, Andrzej N. Wieczorek, Emilia Skołek, Tomasz Borowski, Krzysztof Kotwica, Marek Kalita, Radosław Kruk, Paweł M. Nuckowski

Materials· Volume 16· Issue 12

Abstract

The purpose of this study was to experimentally determine the abrasion wear properties of ausferritic ductile iron austempered at 250 °C in order to obtain cast iron of class EN-GJS-1400-1. It has been found that such a cast iron grade makes it possible to create structures for material conveyors used for short-distance transport purposes, required to perform in terms of abrasion resistance under extreme conditions. The wear tests addressed in the paper were conducted at a ring-on-ring type of test rig. The test samples were examined under the conditions of slide mating, where the main destructive process was surface microcutting via loose corundum grains. The mass loss of the examined samples was measured as a parameter characteristic of the wear. The volume loss values thus obtained were plotted as a function of initial hardness. Based on these results, it has been found that prolonged heat treatment (of more than 6 h) causes only an insignificant increase in the resistance to abrasive wear.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Mechanical and Industrial Engineering, Warsaw University of Technology, Narbutta 85 Street, 02-524 Warsaw, Poland

Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, Akademicka 2 Street, 44-100 Gliwice, Poland

Faculty of Materials Engineering, Warsaw University of Technology, Wołoska 147 Street, 02-507 Warsaw, Poland

Faculty of Mechanical Engineering and Robotics, AGH University of Science and Technology, 30-059 Cracow, Poland

Division of Machines and Equipment, KOMAG Institute of Mining Technology, Pszczyńska 37 Street, 44-101 Gliwice, Poland

Institute of Mechanical Engineering, Clausthal University of Technology, Robert-Koch-Straße 32, D-38678 Clausthal-Zellerfeld, Germany

Materials Research Laboratory, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego 18A Street, 44-100 Gliwice, Poland

Funding

National Centre for Research and Development

References (57)

Show source-provided references
1. (2023, February 18). Global Gears, Drives and Speed Changers Market to Reach US$176.6 Billion by the Year 2026. Available online: https://www.globenewswire.com/news-release/2022/01/14/2367169/0/en/Global-Gears-Drives-and-Speed-Changers-Market-to-Reach-US-176-6-Billion-by-the-Year-2026.html.
2. (2023, May 05). Machine and Oil Condition Supervision. Available online: https://totalenergies.pl/system/files/atoms/files/rozdzial_22_nadzor_nad_stanem_maszyny_i_oleju.pdf.
3. Wang, H., and Li, Z. (2020). IOP Conference Series: Earth and Environmental Science, IOP Publishing.
4. Optimal Inspection and Preventive Maintenance Scheduling of Mining Equipment10.1007/s11668-020-00949-z ↗
5. Designing machinery and equipment in accordance with the principle of sustainable development
6. Review on dynamics of cracked gear systems10.1016/j.engfailanal.2015.06.004 ↗
7. Cause analysis and countermeasure on premature failure of a driven gear for the high-speed train10.1016/j.engfailanal.2022.106487 ↗
8. Ding, H., Wang, Y., Yang, Z., and Pfeiffer, O. (2019). Nonlinear blind source separation and fault feature extraction method for mining machine diagnosis. Appl. Sci., 9.10.3390/app9091852 ↗
9. A new method for the estimation of the instantaneous speed relative fluctuation in a vibration signal based on the short time scale transform10.1016/j.ymssp.2008.07.001 ↗
10. The effect of WC/C coating on the wear of bevel gears used in coal mines
11. The effect of construction changes of the teeth of a gear transmission on acoustic properties10.1080/10803548.2012.11076956 ↗
12. (2019). Calculation of Load Capacity of Spur and Helical Gears—Part 1: Basic Principles, Introduction and General Influence Factors (Standard No. ISO 6336-1:2019).
13. Rana, R. (2020). High-Performance Ferrous Alloys, Springer Cham.10.1007/978-3-030-53825-5 ↗
14. Bhadeshia, H.K.D.H. (2001). Bainite in Steels, The Institute of Materials.
15. Designing with Austempered Ductile Iron
16. Wear Properties of Austempered Ductile Cast Irons
17. (2011). Standard-Austempered Ductile Cast Irons (Standard No. EN 1564:2012).
18. Nili-Ahmadabadi, M., and Shirazi, H. (2015). Encyclopedia of Iron, Steel and Their Alloys, CRC Press.
19. Multiphase ausformed austempered ductile iron10.1515/amm-2017-0231 ↗
20. Zum Gahr, K.H. (1987). Microstructure and Wear of Materials, Elsevier.
21. The particle size effect in abrasion studied by controlled abrasive surfaces10.1016/S0043-1648(98)00344-5 ↗
22. Effects of successive austempering on the tribological behavior of ductile cast iron10.1016/S0043-1648(99)00163-5 ↗
23. Effects of heat treatment on the erosion behavior of austempered ductile irons10.1016/j.wear.2005.04.017 ↗
24. Influence of heat treatment conditions on microstructure and mechanical properties of austempered ductile iron after dynamic deformation test10.2478/amm-2014-0204 ↗
25. Effect of microstructure on abrasion wear behavior of austempered ductile cast iron (ADI) processed by a novel two-step austempering process10.1016/j.msea.2005.06.036 ↗
26. Influence of a novel two-step austempering process on the strain-hardening behaviour of austempered ductile cast iron (ADI)10.1016/j.msea.2004.04.076 ↗
27. Austempered compacted graphite iron—Influence of austempering temperature and time on microstructural and mechanical properties10.1016/j.msea.2019.138434 ↗
28. Sellamuthu, P., Samuel, D.G., Dinakaran, D., Premkumar, V.P., Li, Z., and Seetharaman, S. (2018). Austempered ductile iron (ADI): Influence of austempering temperature on microstructure, mechanical and wear properties and energy consumption. Metals, 8.10.3390/met8010053 ↗
29. The role of operational factors in shaping of wear properties of alloyed Austempered Ductile Iron. Part I. Experimental studies abrasive wear of Austempered Ductile Iron (ADI) in the presence of loose quartz abrasive10.2478/amm-2014-0281 ↗
30. Tribological behavior of shot peened Cu-Ni austempered ductile iron10.1016/j.wear.2012.12.027 ↗
31. Shot peening of austempered ductile iron gears10.1080/02670844.2016.1266118 ↗
32. Influence of shot peening on the fatigue life of Cu-Ni austempered ductile iron10.1016/j.msea.2012.02.092 ↗
33. Wear and friction behavior of austempered ductile iron as railway wheel material10.1016/j.matdes.2015.10.037 ↗
34. Influence of Shot Peening on Abrasion Wear in Real Conditions of Ni-Cu-Ausferritic Ductile Iron10.1515/amm-2016-0320 ↗
35. Nodule count effect on microstructure and mechanical properties of hypo-eutectic adi alloyed with nickel10.2298/JMMB200403009C ↗
36. Influence of step-down austempering process on the fracture toughness of austempered ductile iron
37. Ravishankar, K.S., Rajendra Udupa, K., and Prasad Rao, P. (2008, January 7–11). Development of Austempered Ductile Iron for High Tensile and Fracture toughness by Two Step Austempering Process. Proceedings of the 68th WFC-World Foundry Congress, Chennai, India.
38. Effect of phenomena accompanying wear in dry corundum abrasive on the properties and microstructure of austempered ductile iron with different chemical composition10.1515/amm-2015-0078 ↗
39. Influence of thermal exposure on microstructure evolution and tensile fracture behaviors of compacted graphite iron10.1016/j.msea.2016.03.118 ↗
40. Technologiczne aspekty przemiany odkształceniowej w żeliwie sferoidalnym ausferrytycznym
41. The Role of Operational Factors in Shaping of Wear Properties of Alloyed Austempered Ductile Iron Part II. An Assessment of the Cumulative Effect of Abrasives Processes and the Dynamic Activity on the Wear Property of Ausferritic Ductile Iron10.2478/amm-2014-0282 ↗
42. Szewerda, K., Tokarczyk, J., and Wieczorek, A. (2021). Impact of Increased Travel Speed of a Transportation Set on the Dynamic Parameters of a Mine Suspended Monorail. Energies, 14.10.3390/en14061528 ↗
43. Operation-oriented studies on wear properties of surface-hardened alloy cast steels used in mining in the conditions of the combined action of dynamic forces and an abrasive material10.1515/amm-2017-0351 ↗
44. The first bulk nanostructured metal10.1088/1468-6996/14/1/014202 ↗
45. TEM of nanostructured metals and alloys10.1016/j.msea.2004.01.125 ↗
46. Very Strong Bainite10.1016/j.cossms.2004.09.005 ↗
47. Nanostructured Materials from Severe Plastic Deformation10.1016/S0079-6425(99)00007-9 ↗
48. The effect of grain size on the stress-strain relationship in low-carbon steel
49. Ductilization of nanocrystalline materials for structural applications10.1016/j.scriptamat.2004.05.015 ↗
50. Mechanical Behavior of Nanosrystalline Metals10.1016/0956-716X(90)90582-2 ↗
51. Improving wear resistance of steels through nanocrystalline structures obtained by bainitic transformation10.1080/02670836.2015.1132048 ↗
52. Effect of austenite grain refinement on morphology of product of bainitic reaction in austempered ductile iron10.1179/mst.1993.9.8.705 ↗
53. Nanoausferritic matrix of ductile iron10.1179/1743284714Y.0000000733 ↗
54. Manufacture of toothed elements in nanoausferritic ductile iron10.2478/amm-2014-0211 ↗
55. Panneerselvam, S. (2017). Development of Nanostructured Austempered Ductile Cast Iron. [Ph.D. Thesis, Wayne State University]. Available online: https://digitalcommons.wayne.edu/oa_dissertations/1856.
56. An assessment of the applicability of austempered ductile iron containing Mo and Ni for mining machines parts10.2478/amm-2013-0108 ↗
57. Sobczak, J.J. (2013). Poradnik Odlewnika: Odlewnictwo Współczesne, Publishing house of the Polish Foundrymen’s Technical Association. T. 1: Materiały.