journal article·2020-02-09Open access

Micro-Texture Analyses of a Cold-Work Tool Steel for Additive Manufacturing

Jun-Yun Kang, Jaecheol Yun, Byunghwan Kim, Jungho Choe, Sangsun Yang, Seong-Jun Park, Ji-Hun Yu, Yong-Jin Kim

Materials· Volume 13· Issue 3

Abstract

Small objects of an alloy tool steel were built by selective laser melting at different scan speeds, and their microstructures were analyzed using electron backscatter diffraction (EBSD). To present an explicit correlation with the local thermal cycles in the objects, prior austenite grains were reconstructed using the EBSD mapping data. Extensive growth of austenitic grains after solidification could be detected by the disagreement between the networks of carbides and austenite grain boundaries. A rapid laser scan at 2000 mm/s led to less growth, but retained a larger amount of austenite than a slow one at 50 mm/s. The rapid scan also exhibited definite evolution of Goss-type textures in austenite, which could be attributed to the growth of austenitic grains under a steep temperature gradient. The local variations in the microstructures and the textures enabled us to speculate the locally different thermal cycles determined by the different process conditions, that is, scan speeds.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Korea Institute of Materials Science, 797 Changwon-daero, Changwon, Gyeongnam 51508, Korea

Funding

Korea Institute of Materials Science

References (44)

Show source-provided references
1. Additive manufacturing management: A review and future research agenda10.1080/00207543.2016.1229064 ↗
2. Perspectives on additive manufacturing10.1146/annurev-matsci-070115-031606 ↗
3. Frontiers of 3D printing/additive manufacturing: From human organs to aircraft fabrication10.1016/j.jmst.2016.08.011 ↗
4. (2016). Standard Terminology for Additive Manufacturing—General Principles—Terminology, ASTM International. ISO/ASTM 52900:2015(E).
5. Materials issues in additive manufacturing: A review10.1016/j.jmapro.2016.11.006 ↗
6. Metal additive manufacturing: A review10.1007/s11665-014-0958-z ↗
7. Direct metal additive manufacturing processes and their sustainable applications for green technology: A review10.1007/s40684-016-0048-9 ↗
8. Epitaxy and microstructure evolution in metal additive manufacturing10.1146/annurev-matsci-070115-031728 ↗
9. Metal additive manufacturing: A review of mechanical properties10.1146/annurev-matsci-070115-032024 ↗
10. Microstructural control of additively manufactured metallic materials10.1146/annurev-matsci-070115-031816 ↗
11. Analysis of defect generation in Ti-6Al-4V parts made using powder bed fusion additive manufacturing processes
12. Optimizing quality of additively manufactured Inconel 718 using powder bed laser melting process
13. Surface texture metrology for metal additive manufacturing: A review10.1016/j.precisioneng.2016.06.001 ↗
14. Selective laser melting of iron-based powder10.1016/j.jmatprotec.2003.11.051 ↗
15. Metallurgical and mechanical evaluation of 4340 steel produced by direct metal laser sintering10.1007/s11837-014-1273-8 ↗
16. Plastic anisotropy and deformation-induced phase transformation of additive manufactured stainless steel10.1016/j.msea.2019.138065 ↗
17. Direct additive laser manufacturing using gas- and water-atomised H13 tool steel powders10.1007/s00170-003-1844-2 ↗
18. Experimental study of residual stresses in laser clad AISI P20 tool steel onpre-hardened wrought P20 substrate10.1016/j.msea.2010.07.098 ↗
19. Freeform laser consolidated H13 and CPM 9V tool steels10.1007/s13632-013-0061-0 ↗
20. Characterization of microstructure and residual stress in a 3D H13 tool steel component produced by additive manufacturing10.1557/jmr.2014.190 ↗
21. Microstructure, mechanical behavior, and wear properties of FeCrMoVC steel prepared by selective laser melting and casting10.1016/j.scriptamat.2016.07.029 ↗
22. Microstructures of powders and additively manufactured objects of an alloy tool steel for cold-work dies10.4150/KPMI.2017.24.3.202 ↗
23. (2020, January 13). Additive Manufacturing with Steels 2019, SmarTech Analysis. Available online: http://www.smartechpublishing.com.
24. Roberts, G., Krauss, G., and Kennedy, R. (1998). Tool Steels, ASM Int.. [5th ed.].10.31399/asm.tb.ts5.9781627083584 ↗
25. Nishiyama, Z. (1978). Martensitic Transformation, Academic Press.
26. An advanced approach to reconstructing parent orientation maps in the case of approximate orientation relations: Application to steels10.1016/j.actamat.2012.04.034 ↗
27. Nyyssönen, T. (2017). Quenching and Partitioning of High-Aluminum Steels. [Ph.D. Thesis, Tampere University of Technology].
28. Fully automated orientation relationship calculation and prior austenite reconstruction by random walk clustering10.1088/1757-899X/82/1/012059 ↗
29. Effect of NbC carbide addition on mechanical properties of matrix-type cold-work tool steel10.12656/jksht.2015.28.5.239 ↗
30. Texture analysis with MTEX—Free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
31. (2020, January 13). MTEX Toolbox. Available online: https://mtex-toolbox.github.io.
32. (2020, January 13). MTEX Forum. Available online: https://groups.google.com/forum/#!forum/mtexmail.
33. Dongen, S.M. (2001). Graph Clustering by Flow Simulation. [Ph.D. Thesis, Universiteit Utrecht].
35. New development in electrical strip steels characterized by fine grain structure approaching the properties of a single crystal
36. Humphreys, F.J., and Hatherly, M. (2004). Recrystallization and Related Annealing Phenomena, Elsevier. [2nd ed.].10.1016/B978-008044164-1/50016-5 ↗
37. Evolution of carbides in cold-work tool steels10.1016/j.matchar.2015.08.001 ↗
38. Porter, D.A., and Easterling, K.E. (1992). Phase Transformations in Metals and Alloys, Chapman & Hall. [2nd ed.].10.1007/978-1-4899-3051-4 ↗
39. Leslie, W.C. (1982). The Physical Metallurgy of Steels; International Student Edition, McGraw-Hill Kogakusha.
40. The influence of austenite grain size on the mechanical properties of low-alloy steel with boron10.3390/met7010026 ↗
41. Highly anisotropic steel processed by selective laser melting10.1007/s11663-013-9875-z ↗
42. Evolution of solidification texture during additive manufacturing10.1038/srep16446 ↗
43. Yan, F., Xiong, W., and Faierson, E.J. (2017). Grain structure control of additively manufactured metallic materials. Materials, 10.10.3390/ma10111260 ↗
44. Anisotropic mechanical behavior of additive manufactured AISI 316L steel10.1007/s11661-019-05139-7 ↗