journal article·2022-08-16Open access

Microstructure, Precipitates Behavior, and Mechanical Properties of Age-Hardened Al-Mg-Si Alloy Sheet Fabricated by Twin-Roll Casting

Guanjun Gao, Xiwu Li, Baiqing Xiong, Zhihui Li, Yongan Zhang, Yanan Li, Lizhen Yan

Materials· Volume 15· Issue 16

Abstract

Twin-roll casting (TRC), as a near-net-shape technology, is employed to fabricate age-hardened Al-Mg-Si alloy. Compared with conventional direct chill (DC) casting, the TRC method is much more economical and efficient. In this work, the microstructure, precipitates behavior, and mechanical properties of age-hardened Al-Mg-Si alloy sheet fabricated by TRC were investigated by hardness measurements and tensile tests, metallographic microscopy, field emission gun scanning electron microscope, electron backscatter diffraction, transmission electron microscopy, and differential scanning calorimetry analyses. It was found that the size of recrystallized grains for DC casting alloy with finely dispersed particles was larger than that of TRC alloy with coarse particles. Typical CubeND texture accompanied by P texture formed after solution treatment made the value of r reach ~0.7 in the TRC alloy due to the PSN effect caused by the segregation of particles. More GP zones resulted in the strength of TRC alloy being higher than that of DC casting alloy after T8X treatment. With the time of paint-bake hardening extended to 8 h, few segregation particles remained in the TRC alloy. This decreased the concentration of supersaturated atoms. The hardness of the TRC alloy with the lower density of the β″ strengthening phase was lower compared to the DC casting alloy.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

State Key Laboratory of Non-Ferrous Metals and Processes, GRINM Group Co., Ltd., Beijing 100088, China

GRIMAT Engineering Institute Co., Ltd., Beijing 101407, China

General Research Institute for Nonferrous Metals, Beijing 100088, China

Funding

National Key R&D Program of China

References (35)

Show source-provided references
1. Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications10.1016/j.actamat.2012.10.044 ↗
2. Recent development in aluminium alloys for the automotive industry10.1016/S0921-5093(99)00653-X ↗
3. Microstructural evolution and properties of electromagnetic cast-rolled novel Al–Li alloy under different heat treatment procedures10.1016/j.jmrt.2021.12.036 ↗
4. A new approach to control centerline macrosegregation in Al–Mg–Si alloys during twin roll continuous casting10.1016/j.matlet.2016.12.109 ↗
5. Effect of electromagnetic fields on microstructure and mechanical properties of sub-rapid solidification-processed Al–Mg–Si alloy during twin-roll casting10.1016/j.msea.2019.138328 ↗
6. Effect of second-phase particle evolution in a twin-roll-casted Al-Mg-Si alloy on recrystallization texture and mechanical anisotropy10.1016/j.matchar.2021.111038 ↗
7. Evolution of microstructure and properties during homogenization of the novel Al–Li alloy fabricated by electromagnetic oscillation twin-roll casting10.1016/j.jmrt.2020.01.025 ↗
8. The Effect of Mg/Si Ratio on the Microstructure and Tensile Properties of Twin-Roll-Casting Al–Mg–Si Alloys10.1016/j.matchar.2022.112146 ↗
9. Microstructure evolution and recrystallization behavior of hot rolled AA6061 twin-roll casting plate with different manganese contents10.1016/j.jallcom.2022.165618 ↗
10. Fe-bearing phase formation, microstructure evolution, and mechanical properties of Al-Mg-Si-Fe alloy fabricated by the twin-roll casting process10.1016/j.jallcom.2021.161202 ↗
11. Effect of trace Cr alloying on centerline segregations in sub-rapid solidified Al–Mg–Si (AA6061) alloys fabricated by twin-roll casting10.1016/j.msea.2021.141896 ↗
12. Microstructure and Nano-Segregation of Cu in Al–Mg–Si–Cu Alloys10.2320/materia.42.860 ↗
13. The sequence of precipitation in the Al–Mg–Si–Cu alloy AA611110.1007/BF02586103 ↗
14. The diffraction patterns from β″ precipitates in 12 orientations in Al–Mg–Si alloy10.1016/j.scriptamat.2010.01.039 ↗
15. Pre-precipitate clusters and precipitation processes in Al–Mg–Si alloys10.1016/S1359-6454(99)00033-6 ↗
16. Gao, G., Li, Y., Wang, Z., Di, H., Li, J., and Xu, G. (2019). Effects of the Quenching Rate on the Microstructure, Mechanical Properties and Paint Bake-Hardening Response of Al–Mg–Si Automotive Sheets. Materials, 12.10.3390/ma12213587 ↗
17. Effect of the size distribution of nanoscale dispersed particles on the Zener Drag pressure10.1007/s11661-010-0452-7 ↗
18. The effect of particle content, particle distribution and cold deformation on the recrystallization of low oxide Al–Al2O3 products10.1007/BF00574925 ↗
19. Effect of solution time on microstructure, texture and mechanical properties of Al–Mg–Si–Cu alloys10.1016/j.msea.2015.07.059 ↗
20. Effects of Intermediate Annealing and Cold-rolling on Recrystallization Texture in 1050 Aluminum10.1016/j.proeng.2014.09.153 ↗
21. Influence of particles on recrystallisation textures and microstructures of aluminium alloy 310310.1179/mst.1997.13.2.93 ↗
22. Particle-stimulated nucleation of recrystallization for grain-size control and superplasticity in an Al–Mg–Si–Cu alloy10.1016/S0921-5093(00)01235-1 ↗
23. Texture control by thermomechanical processing of AA6xxx Al–Mg–Si sheet alloys for automotive applications—a review10.1016/S0921-5093(01)01968-2 ↗
24. On the influence of orientation pinning on growth selection of recrystallisation10.1016/S1359-6454(97)00354-6 ↗
25. Correlating r-value and through thickness texture in Al–Mg–Si alloy sheets10.1016/j.jallcom.2014.09.038 ↗
26. Texture Control for Improving Deep Drawability in Rolled and Annealed Aluminum Alloy Sheets10.2320/matertrans.L-MRA2007871 ↗
27. Low-Temperature Differential Scanning Calorimetry of an Al–Mg–Si Alloy10.1007/s11661-010-0596-5 ↗
28. The effects of preaging treatments on aging kinetics and mechanical properties in AA6111 aluminum autobody sheet10.1007/s11661-999-0010-3 ↗
29. Study of retrogression response in naturally and multi-step aged Al-Mg-Si automotive sheets10.1016/j.jallcom.2018.04.198 ↗
30. Detailed atomistic insight into the β″ phase in Al-Mg-Si alloys10.1016/j.actamat.2014.01.052 ↗
31. Atomic Pillar-Based Nanoprecipitates Strengthen AlMgSi Alloys10.1126/science.1124199 ↗
32. On the effects of thermomechanical processing on failure mode in precipitation-hardened aluminium alloys10.1023/A:1021095801205 ↗
33. Effect of multi-stage aging on the precipitation strengthening and mechanical properties for an Al-Mg-Si-Ag alloy10.1016/j.matchar.2022.112004 ↗
34. Analysis of the metastable precipitates in peak-hardness aged Al–Mg–Si(–Cu) alloys with differing Si contents10.1016/j.actamat.2017.04.037 ↗
35. Influence of treatment pathways on the precipitation behaviors of Al–Mg–Si–Cu–(Zn)–Mn alloys10.1016/j.jallcom.2019.05.055 ↗