Research on Spheroidization of Tungsten Powder from Three Different Raw Materials
Source abstract
Abstract
In this work, three kinds of tungsten powders with different particle sizes were spheroidized by radio-frequency (RF) inductively coupled plasma spheroidization. The spheroidization behavior of these tungsten powders was investigated and compared. The spheroidization effects of irregular tungsten powder improves with the decrease in degree of agglomeration and increases with primary particle size. Spherical tungsten powder from irregular powder with a primary particle size of 19.9 μm and an agglomeration coefficient of 1.59 had the best spheroidization effect; its apparent density, hall flow time, and spheroidization ratio are 9.36 g/cm3, 6.28 s/50 g, and 98%, respectively. The results show that irregular feedstock tungsten powder with a smaller primary particle size and higher agglomeration degree has a poor spheroidization effect because it is easily affected by the gas flow and deviates from the high temperature zone. On the contrary, irregular feedstock tungsten powder with larger primary particle sizes and lower agglomeration degrees has better spheroidization effects.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Henan Province Industrial Technology Research Institute of Resources and Materials, Zhengzhou University, Zhengzhou 450001, China
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001, China
School of Materials Science and Engineering, Henan University of Technology, Zhengzhou 450001, China
Funding
National Key Research and Development Program · China Postdoctoral Science Foundation
References (32)
Show source-provided references
1. Low temperature carburization of high surface area tungsten powders10.1016/0965-9773(95)00265-G ↗
2. Development of a powder metallurgy process for tungsten components10.1016/j.fusengdes.2008.06.022 ↗
3. Development of tungsten and tungsten alloys for DEMO divertor applications via MIM technology10.1016/j.jnucmat.2013.01.004 ↗
4. Chemical vapor synthesis (CVS) of tungsten nanopowder in a thermal plasma reactor10.1016/j.ijrmhm.2008.06.002 ↗
5. Numerical simulation and prediction of radio frequency inductively coupled plasma spheroidization10.1016/j.applthermaleng.2016.02.108 ↗
6. In-situ synthesis of tungsten nanoparticle attached spherical tungsten micro-powder by inductively coupled thermal plasma process10.1016/j.ijrmhm.2015.04.029 ↗
7. Nanostructured α/β-tungsten by reduction of WO3 under microwave plasma10.1016/j.ijrmhm.2010.09.005 ↗
8. Measuring the brittle-to-ductile transition temperature of tungsten–tantalum alloy using chevron-notched micro-cantilevers10.1016/j.scriptamat.2020.01.030 ↗
9. Recent Advances on High-Entropy Alloys for 3D Printing10.1002/adma.201903855 ↗
10. Analysis of laser-induced microcracking in tungsten under additive manufacturing conditions: Experiment and simulation10.1016/j.actamat.2020.04.060 ↗
11. Rapid additive manufacturing of MR compatible multipinhole collimators with selective laser melting of tungsten powder10.1118/1.4769122 ↗
12. Influence of process parameters on the characteristics of TiAl alloyed powders by fluidized bed jet milling10.1016/j.powtec.2013.11.013 ↗
13. Additive manufacturing of NiTi shape memory alloys using pre-mixed powders10.1016/j.jmatprotec.2019.03.025 ↗
14. Additive manufacturing of tungsten using directed energy deposition for potential nuclear fusion application10.1016/j.surfcoat.2021.126884 ↗
15. Powder-spreading mechanisms in powder-bed-based additive manufacturing: Experiments and computational modeling10.1016/j.actamat.2019.08.030 ↗
16. A theoretical model for the stick/bounce behaviour of adhesive, elastic-plastic spheres10.1016/S0032-5910(98)00099-0 ↗
17. Adhesive force distributions for tungsten dust deposited on bulk tungsten and beryllium-coated tungsten surfaces10.1016/j.nme.2018.05.013 ↗
18. Modelling of dust generation, transport and remobilization in full-metal fusion reactors10.1088/1361-6587/ac4b94 ↗
19. Fabrication of spherical Ti–6Al–4V powder for additive manufacturing by radio frequency plasma spheroidization and deoxidation using calcium10.1016/j.jmrt.2020.10.054 ↗
20. Single-step pathway for the synthesis of tungsten nanosized powders by RF induction thermal plasma10.1016/j.ijrmhm.2011.09.002 ↗
21. Study on behaviors of tungsten powders in radio frequency thermal plasma10.1016/j.ijrmhm.2017.01.017 ↗
22. The Role of Transport Phenomena and Modeling in the Development of Thermal Plasma Technology10.1007/s11090-015-9660-7 ↗
23. New frontiers in thermal plasmas from space to nanomaterials10.5516/NET.77.2012.001 ↗
24. Effect of central gas velocity and plasma power on the spheroidizing copper powders of radio frequency plasma10.1016/j.vacuum.2020.109195 ↗
25. Preparation of spherical tungsten and titanium powders by RF induction plasma processing10.1007/s12598-014-0293-4 ↗
26. Injection molding of tungsten powder treated by jet mill with high powder loading: A solution for fabrication of dense tungsten component at relative low temperature10.1016/j.ijrmhm.2016.10.015 ↗
27. Spheroidization of a granulated molybdenum powder by radio frequency inductively coupled plasma10.1016/j.ijrmhm.2019.03.023 ↗
28. Drag coefficient and terminal velocity of spherical and nonspherical particles10.1016/0032-5910(89)80008-7 ↗
29. Influence of metal powder shape on drag coefficient in a spray jet10.1016/j.cap.2008.06.005 ↗
30. Particle behavior in thermal plasmas10.1007/BF01015878 ↗
31. Induction plasma spheroidization of tungsten and molybdenum powders10.1016/S1003-6326(06)60003-4 ↗
32. Study on the RF inductively coupled plasma spheroidization of refractory W and W-Ta alloy powders10.1088/2058-6272/aa8e94 ↗