Drilling Strategies to Improve the Geometrical and Dimensional Accuracy of Deep through Holes Made in PA6 Alloy
Source abstract
Abstract
This article shows how different drilling strategies may affect the geometrical and dimensional accuracy of deep through holes. The tests were conducted on a three-axis direct-drive turning center. The holes were drilled in cylindrical PA6 aluminum alloy specimens 30 mm in length and 30 mm in diameter using 6 mm Ø VHM HPC TiAlN-coated twist drill bits. The cutting fluid was supplied to the cutting zone through the spindle. The experiments involved applying three strategies to drill deep through (5D) holes. The first required the workpiece to be fixed and the tool to perform both rotary and reciprocating motions. The second assumed that the workpiece performed the primary (rotary) motion whereas the tool moved in reciprocating motion. In the third strategy, the workpiece and the tool rotated in opposite directions and the tool also performed a reciprocating motion. The straightness, roundness, cylindricity, and diameter errors were the key output parameters in the analysis of the geometrical and dimensional accuracy of holes. The Taguchi orthogonal array design of experiment (DOE) was employed to determine the effects of the input (cutting) parameters (i.e., spindle speed and feed per revolution) and the type of hole making strategy on the hole errors by means of multi-factor statistical analysis ANOVA. The use of the highest spindle speed (n = 4775 rpm), the highest feed per revolution (fn = 0.14 mm/rev) and strategy I resulted in the lowest values of the output parameters (STR = 22.7 µm, RON = 8.6 µm, CYL = 28.2 µm, and DE = 9.9 µm). Strategy I was reported to be the most effective for hole drilling in PA6 aluminum alloy because, irrespective of the values of the process parameters used, three out of four output parameters, i.e., straightness, roundness and diameter errors, reached the lowest values.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Machine Design and Machining, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
Department of Metrology and Unconventional Manufacturing, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
Faculty of Marine Engineering, Maritime University of Szczecin, ul. Wały Chrobrego 1-2, 70-500 Szczecin, Poland
References (29)
Show source-provided references
1. Astakhov, V.P. (2014). Drills: Science and Technology od Advanced Operations, Chapman and Hall/CRC.
2. Optimization of CNC Turning Parameters on Aluminium Alloy 6063 using TaguchiRobust Design
3. Yash Doshi, E.P. (2022, January 11). Aluminum Market Outlook—2026. Available online: https://www.alliedmarketresearch.com/aluminium-market.
4. Application of modern aluminum alloys to aircraft10.1016/0376-0421(95)00004-6 ↗
5. Hole quality and burr reduction in drilling aluminium sheets10.1016/j.cirpj.2012.03.005 ↗
6. Wpływ wybranych parametrów skrawania na dokładność obróbki w procesie wiercenia stopu Ti6Al4V
7. Assessment of cutting forces and hole quality in drilling Al2024 alu-minium alloy: Experimental and finite element study10.1007/s00170-016-8563-y ↗
8. An Investigation of burrs, chip formation, hole size, circularity and delamination during drilling operation of GLARE using ANOVA10.1016/j.compstruct.2016.10.015 ↗
9. Characterization of hole quality and temperature in drilling of Al/CFRP stacks under different process condition10.1016/j.procir.2019.02.074 ↗
10. Optimization of process parame-ters in drilling of epoxy Si3N4 composite material10.1016/j.matpr.2015.07.300 ↗
11. Optimization of drilling characteristics using Grey Relational Anal-ysis (GRA) in Medium Density Fiber Board (MDF)10.1016/j.matpr.2015.07.080 ↗
12. Parametric Modeling in Drilling of Die Steels using Taguchi Method based Response Surface Anal-ysis10.1016/j.matpr.2017.12.023 ↗
13. Optimization of drilling parameters using Taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically HSS drills10.1007/s10845-013-0783-5 ↗
14. Effect of machining parameters and coating on wear mechanisms in dry drilling of aluminium alloys10.1016/j.ijmachtools.2005.01.026 ↗
15. Evaluation of drilled hole quality in Al 2024 alloy10.1007/s00170-007-1049-1 ↗
16. The Influence of graphite, MOS2 and Blasocut lubricant on hole and chip geometry during peck drilling of aerospace alloy10.1016/j.matpr.2020.04.323 ↗
17. Bronis, M., Miko, E., Nowakowski, L., and Bartoszuk, M. (2022). A Study of the Kinematics System in Drilling Inconel 718 for Improving of Hole Quality in the Aviation and Space Industries. Materials, 15.10.3390/ma15165500 ↗
18. Bronis, M., Miko, E., and Nowakowski, L. (2021). Analyzing the Effects of the Kinematic System on the Quality of Holes Drilled in 42CrMo4 + QT Steel. Materials, 14.10.3390/ma14144046 ↗
19. Bronis, M., Miko, E., and Nowakowski, L. (2021). Influence of the Kinematic System on the Geometrical and Dimensional Accuracy of Holes in Drilling. Materials, 14.10.3390/ma14164568 ↗
20. Effect of drilling parameters on hole quality and delamination of hybrid GLARE laminate10.1016/j.compstruct.2017.11.073 ↗
21. The effects of cutting conditions on cutting temperature and hole quality in drilling of Inconel 718 using solid carbide drills10.1016/j.jmapro.2018.01.003 ↗
22. Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes10.1007/s00170-007-1368-2 ↗
23. Optimization of process parameters of small hole dry drilling in Ti-6Al-4V using Taguchi and grey relational analysis10.1016/j.measurement.2013.11.020 ↗
24. Tool wear and hole quality evaluation in cryogenic Drilling of Inconel 718 superalloy10.1016/j.triboint.2019.106084 ↗
25. Quality improvement of deep-hole drilling process of AISI D210.1007/s00170-013-5178-4 ↗
26. Investigations into solid lubricant filled textured tools on hole geome-try and surface integrity during drilling of aluminium alloy10.1016/j.matpr.2020.01.163 ↗
27. Optimization of surface roughness and hole diameter accuracy in drilling of EN-31 alloy steel—A TGRA based analysis10.1016/j.matpr.2020.02.611 ↗
28. Simultaneous optimization of material removal rate and surface roughness for WEDM of WCCo composite using grey relational analysis along with Taguchi method
29. Optimization of multi machining characteristics in WEDM of WC-5.3%Co composite using integrated approach of Taguchi, GRA and entropy method10.1007/s11465-012-0333-4 ↗