journal article·2023-05-09Open access

Numerical Analysis of Fracture Behaviour for Cracked Joints in Corrugated Plate Girders Repaired by Stop-Holes

Qifei Wang, Wenfeng Zhou, Zhiyu Wang, Sijie Xiang, Guowen Yao, Qunyi Huang, Yinggai Liu

Materials· Volume 16· Issue 10

Abstract

The efficient crack eliminated stop-hole measure was proposed to repair and reduce the stress concentration associated fracture risk of the corrugated plate girders by setting it at the critical joint of flange plate with tightened bolts and gaskets under preloading. To investigate the fracture behaviour of these repaired girders, parametric finite element analysis was conducted, focusing on the mechanical feature and stress intensity factor of crack stop-hole in this paper. The numerical model was verified against experimental results first, and then the stress characteristics due to the presence of crack open-hole were analysed. It was found that the moderate-sized open-hole was more effective than the over-sized open-hole in the reduction of stress concentration. For the model with prestressed crack stop-hole through bolt preloading, the stress concentration was nearly 50% with the prestress around open-hole increased to 46 MPa, but such a reduction is inconspicuous for even higher prestress. Relatively high circumferential stress gradients and the crack open angle of oversized crack stop-holes were decreased owing to additional prestress effects from the gasket. Finally, the shift from the original tensile area around the edge of the crack open-hole that was prone to fatigue cracking to a compression-oriented area is beneficial for the reduction of stress intensity factor of the prestressed crack stop-holes. It was also demonstrated that the enlargement of crack open-hole has limited influence on the reduction of stress intensity factor and crack propagation. In contrast, higher bolt prestress was more beneficial in consistently reducing the stress intensity factor of the model with the crack open-hole, even containing long crack.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Structural Load-Bearing Analysis · Fatigue and fracture mechanics · Mechanical stress and fatigue analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Key Laboratory of Deep Underground Science and Engineering (Ministry of Education), School of Architecture and Environment, Sichuan University, Chengdu 610065, China

CREGC Architectural & Construction Engineering Co., Ltd., Chengdu 610031, China

State Key Laboratory of Mountain Bridge & Tunnel Engineering, Chongqing Jiaotong University, Chongqing 400074, China

College of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China

Funding

Open Fund of State Key Laboratory of Mountain Bridge and Tunnel Engineering, Chongqing Jiaotong University · Sichuan Science and Technology Program

References (36)

Show source-provided references
1. Corrugated webs in plate girders for bridges10.1680/istbu.1997.29305 ↗
2. Shear response of trapezoidal profiled webs in girders with concrete-filled RHS Flanges10.1016/j.engstruct.2018.07.025 ↗
3. Steel-concrete composite bridges: Design, Life Cycle Assessment, maintenance, and decision-making10.1155/2020/8823370 ↗
4. Huang, H., Chen, K., Wu, Q., and Nakamura, S. (2022). Research on the fatigue performance of composite girders with CSW and St Truss. Appl. Sci., 12.10.3390/app122211703 ↗
5. New developments in steel and Composite Bridges10.1016/j.jcsr.2020.106277 ↗
6. Fatigue behaviour of slender corrugated webs subjected to plate breathing10.1016/j.ijfatigue.2018.12.028 ↗
7. Fatigue of web-flange weld of corrugated web girders: 1. influence of web corrugation geometry and flange geometry on web-flange weld toe stresses10.1016/j.ijfatigue.2004.08.006 ↗
8. Fatigue assessment of Welds joining corrugated steel webs to flange plates10.1016/j.engstruct.2014.04.041 ↗
9. AASHTO (2004). AASHTO LRFD Bridge Design Specifications, AASHTO. [3rd ed.].
10. Fatigue life of girders with trapezoidal corrugated webs10.1061/(ASCE)0733-9445(2006)132:7(1070) ↗
11. Fatigue Strength Evaluation of welded structural details in corrugated steel web girders10.1007/s13296-013-4012-z ↗
12. Fatigue life of girders with trapezoidally corrugated webs: An experimental study10.1016/j.ijfatigue.2014.02.017 ↗
13. Assessment of surface crack growth of composite girders with concrete-filled tubular flanges and corrugated webs through substructure-based numerical modelling10.1016/j.engstruct.2021.113613 ↗
14. Stress characteristics and fatigue crack behaviour of the longitudinal rib-to-cross beam joints in an orthotropic steel deck10.1260/136943308784466224 ↗
15. A stop-hole method for marine and offshore structures10.1016/j.ijfatigue.2016.03.010 ↗
16. Improvement of stop-hole method on fatigue-cracked steel plates by using high-strength bolts and CFRP strips10.1155/2021/6632212 ↗
17. Stop drilling procedure for Fatigue Life Improvement10.1016/j.ijfatigue.2004.04.009 ↗
18. Optimization of stop-hole parameters for cracks at diaphragm-to-rib weld in Steel Bridges10.1016/j.jcsr.2019.105747 ↗
19. Fatigue life extension by crack repair using stop-hole technique under pure mode-I and pure mode-II loading conditions10.1016/j.proeng.2014.06.216 ↗
20. Mixed mode fatigue crack initiation and growth in a CT specimen repaired by stop hole technique10.1016/j.engfracmech.2015.03.027 ↗
21. New crack stop hole shape using structural optimizing technique10.1016/j.asej.2015.02.010 ↗
22. Fatigue damage repair: A comparison of some possible methods10.1016/S0142-1123(96)00029-1 ↗
23. A numerical study on the effect of symmetric crack flank holes on fatigue life extension of a sent specimen10.1111/ffe.12199 ↗
24. The retardation effect of combined application of stop-hole and overload on Sheet Steel10.1016/j.ijfatigue.2019.105414 ↗
25. Retardation of fatigue crack growth in high strength steel S690 using a modified stop-hole technique10.1016/j.engfracmech.2016.11.013 ↗
26. Crack-growth arrest by redirecting crack growth by drilling stop holes and inserting pins into them10.1016/j.engfailanal.2008.06.009 ↗
27. Stress concentration at stop-drilled holes and additional holes10.1016/j.engfailanal.2007.11.002 ↗
28. A crack-growth arresting technique in aluminum alloy10.1016/j.engfailanal.2007.02.005 ↗
29. A new proposal for retarding fatigue crack reinitiation and growth from crack-tip introduced stop-drilled hole by providing additional holes10.2472/jsms.56.1139 ↗
30. Fatigue strength evaluation of out-of-plane gusset welded joints repaired by bolting-stop-hole method
31. (2015). BS Code of Practice for Fatigue Design and Assessment of Steel Structures (Standard No. BS7608).
32. Recho, N. (2012). Fracture Mechanics and Crack Growth, Wiley.10.1002/9781118387184 ↗
33. Reduction of stress concentration at edge of stop hole by closing crack surface10.2472/jsms.62.33 ↗
34. Fatigue behaviour of composite girders with concrete-filled tubular flanges and corrugated webs—Experimental study10.1016/j.engstruct.2021.112416 ↗
35. FHWA (2013). Manual for Repair and Retrofit of Fatigue Cracks in Steel Bridges.
36. Crack stop holes in steel bridge decks: Drilling method and effects10.1007/s11771-017-3649-8 ↗