Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy
Source abstract
Abstract
Here, 0.3 wt.%Zr was introduced in an Al-4 wt.%Cu-0.5 wt.%Mn-0.1 wt.%Fe alloy to investigate its influence on the microstructure and mechanical properties of the alloy. The microstructures of both as-cast and T6-treated Al–Cu–Mn–Fe (ACMF) and Al–Cu–Mn–Fe–Zr (ACMFZ) alloys were analyzed. The intermetallic compounds formed through the casting procedure include Al2Cu and Al7Cu2Fe, and the Al2Cu phase dissolves into the matrix and re-precipitates as θ′ phase during the T6 process. The introduction of Zr results in the precipitation of L12-Al3Zr nanometric precipitates after T6, while the θ′ precipitates in ACMFZ alloy are much finer than those in ACMF alloy. The L12-Al3Zr precipitates were found coherently located with θ′, which was assumed beneficial for stabilizing the θ′ precipitates during the high-temperature tensile process. The tensile properties of ACMF and ACMFZ alloys at room temperature and elevated temperatures (200, 300, and 400 °C) were tested. Especially, the yield strength of ACMFZ alloys can reach 128 MPa and 65 MPa at 300 °C and 400 °C, respectively, which are 31% and 33% higher than those of ACMF alloys. The strengthening mechanisms of grain size, L12-Al3Zr, and θ′ precipitates on the tensile properties were discussed. This work may be referred to for designing Al–Cu alloys for application in high-temperature fields.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, 17923 Jingshi Road, Jinan 250061, China
Funding
Natural Science Foundation of Shandong Province · Key Research and Development Program of Shandong Province
References (73)
Show source-provided references
1. Recent Developments in Advanced Aircraft Aluminium Alloys
2. Recent Development in Aluminium Alloys for the Automotive Industry10.1016/S0921-5093(99)00653-X ↗
3. Advanced Casting Technologies for Lightweight Automotive Applications
4. Precipitation kinetics in metallic alloys: Experiments and modeling10.1016/j.actamat.2021.117338 ↗
5. The Intelligent Design of High Strength, Creep-Resistant Aluminum Alloys10.4028/www.scientific.net/MSF.396-402.21 ↗
6. Design and development of an experimental wrought aluminum alloy for use at elevated temperatures10.1007/BF02628387 ↗
7. Characterization of the Aging Precipitates of Al-12Si-4Cu-2Ni-0.8Mg-0.2Gd Piston Alloy10.1007/s11837-018-3080-0 ↗
8. High Strength and Good Ductility of Casting Al–Cu Alloy Modified by PrxOy and LaxOy10.1016/j.jallcom.2010.09.059 ↗
9. Qiu, F., Gao, X., Tang, J., Gao, Y.Y., Shu, S.L., Han, X., Li, Q., and Jiang, Q.C. (2017). Microstructures and Tensile Properties of Al–Cu Matrix Composites Reinforced with Nano-Sized SiCp Fabricated by Semisolid Stirring Process. Metals, 7.10.3390/met7020049 ↗
10. Variation of Microstructure and Mechanical Properties with Nano-SiCp Levels in the Nano-SiCp/AlCuMnTi Composites10.1016/j.jallcom.2018.08.066 ↗
11. Enhanced Mechanical Properties of High-Temperature-Resistant Al–Cu Cast Alloy by Microalloying with Mg10.1016/j.jallcom.2020.154305 ↗
12. The Influence of Sc Solute Partitioning on Ductile Fracture of Sc-Microalloyed Al-Cu Alloys10.1016/j.msea.2018.01.078 ↗
13. The Synergistic Role of Mn and Zr/Ti in Producing θ′/L12 Co-Precipitates in Al-Cu Alloys10.1016/j.actamat.2020.05.043 ↗
14. Solute Segregation at the Al/θ′-Al2Cu Interface in Al-Cu Alloys10.1016/j.actamat.2017.09.020 ↗
15. Effects of Compositional Variation on the Thermal Stability of θ′-Al2Cu Precipitates and Elevated-Temperature Strengths in Al-Cu 206 Alloys10.1007/s11665-020-05227-5 ↗
16. Heterogeneities in Solid Solutions10.1016/S0081-1947(08)60568-8 ↗
17. Application of ANOVA Method to Precipitation Behaviour Studies10.1016/j.msea.2005.02.021 ↗
18. Effect of Mo, Zr, and Y on the High-Temperature Properties of Al–Cu–Mn Alloy10.1557/jmr.2019.288 ↗
19. Davis, J.R., Allen, P., Lampman, S., Zorc, T.B., Henry, S.D., Daquila, J.L., and Ronke, A.W. (1990). Metals Handbook: Volume 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International.
20. Structure and phase composition of alloys of the Al-Ce-Cu system in the region of the Al-Al8CeCu4 quasi-binary join10.3103/S1067821207010099 ↗
21. Evolution of Microstructure and Mechanical Properties of a New Al–Cu–Er Wrought Alloy10.1134/S0031918X19060097 ↗
22. Influence of La on the atomic structure of AlCu alloy liquid10.1016/j.molliq.2022.119143 ↗
23. Microstructure and materials characterisation of the novel Al–Cu–Y alloy10.1080/02670836.2018.1460536 ↗
24. Amer, S., Barkov, R., and Pozdniakov, A. (2021). Microstructure and Mechanical Properties of Novel Quasibinary Al-Cu-Yb and Al-Cu-Gd Alloys. Metals, 11.10.3390/met11030476 ↗
25. Selective Laser Melting of an Al–Fe–V–Si Alloy: Microstructural Evolution and Thermal Stability10.1016/j.jmst.2016.09.015 ↗
26. Effect of Mn substitution on Cr in the Al-Cu-Er-Mg–Zr–Fe–Si–Ti cast alloy10.1016/j.jallcom.2024.173958 ↗
27. Advances in Microstructural Understanding of Wrought Aluminum Alloys10.1007/s11661-020-05908-9 ↗
28. Tailoring the Strengthening Particles in Aluminum Alloys by Microalloying
29. Elevated Temperature Microstructural Stability in Cast AlCuMnZr Alloys through Solute Segregation10.1016/j.msea.2019.138279 ↗
30. Co-Stabilization of θ′-Al2Cu and Al3Sc Precipitates in Sc-Microalloyed Al–Cu Alloy with Enhanced Creep Resistance10.1016/j.mtnano.2019.100035 ↗
31. Stabilizing Nanoprecipitates in Al-Cu Alloys for Creep Resistance at 300 °C10.1080/21663831.2018.1546773 ↗
32. Structure and Properties of New Heat-Resistant Cast Alloys Based on the Al–Cu–Y and Al–Cu–Er Systems10.1134/S0031918X21090027 ↗
33. Microstructure and Mechanical Properties of a Precipitation-Strengthened Al-Zr-Sc-Er-Si Alloy with a Very Small Sc Content10.1016/j.actamat.2017.10.040 ↗
34. The influence of Sc solute partitioning on the microalloying effect and mechanical properties of Al-Cu alloys with minor Sc addition10.1016/j.actamat.2016.08.013 ↗
35. Application of Element Zr in Aluminum Alloys
36. Enhancement of high temperature strength of Al-Cu alloys by minor alloying and hot working process10.1016/j.jallcom.2022.166136 ↗
37. Enhancing Elevated Temperature Strength of Copper Containing Aluminium Alloys by Forming L12 Al3Zr Precipitates and Nucleating θ″ Precipitates on Them10.1038/s41598-017-11540-2 ↗
38. Precipitation of iron-rich intermetallic phases in Al-4.6Cu-0.5Fe-0.5Mn cast alloy10.1007/s10853-012-6279-4 ↗
39. Microstructures and mechanical properties of squeeze cast Al–5.0Cu–0.6Mn alloys with different Fe content10.1016/j.matdes.2013.05.079 ↗
40. Belov, N.A., Aksenov, A.A., and Eskin, D.G. (2002). Iron in Aluminium Alloys: Impurity and Alloying Element, CRC Press.10.1201/9781482265019 ↗
41. Removal of iron from aluminum: A review10.1080/08827508.2010.542211 ↗
42. Green, J.A.S. (2007). Aluminum Recycling and Processing for Energy Conservation and Sustainability, ASM International.
43. Effect of Mn, Si, and Cooling Rate on the Formation of Iron-Rich Intermetallics in 206 Al–Cu Cast Alloys10.1007/s11663-012-9694-7 ↗
44. Dispersoid particles precipitated during the solutionizing course of Al-12wt%Si-4wt%Cu-1.2wt%Mn alloy and their influence on high temperature strength10.1016/j.msea.2017.04.091 ↗
45. Uneven Precipitation Behavior during the Solutionizing Course of Al-Cu-Mn Alloys and Their Contribution to High Temperature Strength10.1155/2018/6741502 ↗
46. Effect of Thermal Exposure on Microstructure and Mechanical Properties of Al−Si−Cu−Ni−Mg Alloy Produced by Different Casting Technologies10.1016/S1003-6326(20)65333-X ↗
47. Micro-Mechanism of Simultaneous Improvement of Strength and Ductility of Squeeze-Cast Al–Cu Alloy10.1016/j.msea.2021.142538 ↗
48. Mechanism for Zr Poisoning of Al-Ti-B Based Grain Refiners10.1016/j.actamat.2018.10.056 ↗
49. Grain refining mechanism in the Al/Al–Ti–B system10.1016/j.actamat.2014.10.055 ↗
50. Effect of Ce addition on microstructure of Al20Cu2Mn3 twin phase in an Al–Cu–Mn casting alloy10.1016/j.msea.2011.11.025 ↗
51. Effects of Nd on microstructure and mechanical properties of cast Al-Si-Cu-Ni-Mg piston alloys10.1016/j.jallcom.2016.10.300 ↗
52. Influence of Cu content on the microstructure and high-temperature tensile and fatigue properties of secondary AlSi7Mg0.3VZr alloys10.1016/j.msea.2021.141310 ↗
53. A novel heat-resistant Al–Si–Cu–Ni–Mg base material synergistically strengthened by Ni-rich intermetallics and nano-AlNp microskeletons10.1016/j.jmst.2018.09.051 ↗
54. Enhanced elevated-temperature properties via Mo addition in Al-Mn-Mg 3004 alloy10.1016/j.jallcom.2016.10.005 ↗
55. Effect of Cu and Mn Content on Solidification Microstructure, T-Phase Formation and Mechanical Property of Al Cu Mn Alloys10.1016/j.jallcom.2018.09.362 ↗
56. A regime beyond the Hall–Petch and inverse-Hall–Petch regimes in ultrafine-grained solids10.1038/s42005-022-01107-7 ↗
57. An interpretation of the effect of grain size on high temperature strength10.1007/BF02643158 ↗
58. Strengthening Effect of Unshearable Particles of Finite Size: A Computer Experimental Study10.1016/S1359-6454(99)00179-2 ↗
59. Strengthening of an Al–Cu–Sn Alloy by Deformation-Resistant Precipitate Plates10.1016/j.actamat.2008.03.028 ↗
60. The Effect of Shear-Resistant, Plate-Shaped Precipitates on the Work Hardening of Al Alloys: Towards a Prediction of the Strength-Elongation Correlation10.1016/j.actamat.2009.08.034 ↗
61. On the Strengthening Response of Aluminum Alloys Containing Shear-Resistant Plate-Shaped Precipitates10.1016/j.actamat.2008.08.023 ↗
62. Enhanced Thermal Stability and Mechanical Properties of High-Temperature Resistant Al−Cu Alloy with Zr and Mn Micro-Alloying10.1016/S1003-6326(21)65778-3 ↗
63. Precipitates in Al–Cu Alloys Revisited: Atom-Probe Tomographic Experiments and First-Principles Calculations of Compositional Evolution and Interfacial Segregation10.1016/j.actamat.2011.06.036 ↗
64. Interfacial Segregation at Cu-Rich Precipitates in a High-Strength Low-Carbon Steel Studied on a Sub-Nanometer Scale10.1016/j.actamat.2005.10.023 ↗
65. Equilibrium Segregation and Interfacial Energy in Multicomponent Systems10.1016/0956-7151(91)90277-8 ↗
66. Simultaneous Segregation at Coherent and Semicoherent Heterophase Interfaces10.1103/PhysRevLett.105.076102 ↗
67. Enhanced Thermal Stability of Precipitates and Elevated-Temperature Properties via Microalloying with Transition Metals (Zr, V and Sc) in Al–Cu 224 Cast Alloys10.1016/j.msea.2021.142090 ↗
68. Mechanisms for Stabilizing θ′(Al2Cu) Precipitates at Elevated Temperatures Investigated with Phase Field Modeling10.1016/j.mtla.2019.100335 ↗
69. Research Progress in Zr-microalloying Strengthened Aluminum Alloys
70. (Al, Zn)3Zr Dispersoids Assisted η′ Precipitation in an Al-Zn–Mg–Cu–Zr Alloy10.1016/j.mtla.2020.100641 ↗
71. Contributions to High Temperature Strengthening from Three Types of Heat-Resistant Phases Formed during Solidification, Solution Treatment and Ageing Treatment of Al-Cu-Mn-Ni Alloys Respectively10.1016/j.msea.2019.138819 ↗
72. Microstructure and Tensile Properties of the Sub-Micro and Nano-Structured Al Produced by Laser Surface Melting10.1016/j.msea.2010.08.008 ↗
73. High-Temperature Dynamic Compressive Properties of Two Monolithic Zr-Based Amorphous Alloys10.1016/j.jallcom.2008.12.045 ↗