Tailoring Titanium Sheet Metal Using Laser Metal Deposition to Improve Room Temperature Single-Point Incremental Forming
Source abstract
Abstract
Typically, due to their limited formability, elevated temperatures are required in order to achieve complex shapes in titanium alloys. However, there are opportunities for forming such alloys at room temperature using incremental forming processes such as single-point incremental forming (SPIF). SPIF is an innovative metal forming technology which uses a single tool to form sheet parts in place of dedicated dies. SPIFs ability to increase the forming limits of difficult-to-form materials offers an alternative to high temperature processing of titanium. However, sheet thinning during SPIF may encourage the early onset of fracture, compromising in-service performance. An additive step prior to SPIF has been examined to tailor the initial sheet thickness to achieve a homogeneous thickness distribution in the final part. In the present research, laser metal deposition (LMD) was used to locally thicken a commercially pure titanium grade 2 (CP-Ti50A) sheet. Tensile testing was used to examine the mechanical behaviour of the tailored material. In addition, in-situ digital image correlation was used to measure the strain distribution across the surface of the tailored material. The work found that following deposition, isotropic mechanical properties were obtained within the sheet plane in contrast to the anisotropic properties of the as-received material and build height appeared to have little influence on strength. Microstructural analysis showed a change to the material in response to the LMD added thickness, with a heat affected zone (HAZ) at the interface between the added LMD layer and non-transformed substrate material. Grain growth and intragranular misorientation in the added LMD material was observed. SPIF of a LMD tailored preform resulted in improved thickness homogeneity across the formed part, with the downside of early fracture in a high wall angle section of the sheet.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Additive Manufacturing Materials and Processes · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Design, Manufacturing & Engineering Management, University of Strathclyde, Glasgow G1 1XJ, Scotland, UK
Advanced Forming Research Centre, Inchinnan PA4 9LJ, Scotland, UK
Funding
Advanced Forming Research Centre, University of Strathclyde, and Faculty of Engineering
References (26)
Show source-provided references
1. The Increased Forming Limits of Incremental Sheet Forming Processes10.4028/www.scientific.net/KEM.344.621 ↗
2. More, K.R., Sisodia, V., and Kumar, S. (2021). A Brief Review on Formability, Wall Thickness Distribution and Surface Roughness of Formed Part in Incremental Sheet Forming. Advances in Manufacturing Processes, Springer. Lecture Notes in Mechanical Engineering.10.1007/978-981-15-9117-4_11 ↗
3. The mechanics of incremental sheet forming10.1016/j.jmatprotec.2008.03.025 ↗
4. Oleksik, V., Trzepieciński, T., Szpunar, M., Chodoła, Ł., Ficek, D., and Szczęsny, I. (2021). Single-point incremental forming of titanium and titanium alloy sheets. Materials, 14.10.3390/ma14216372 ↗
5. Trzepiecinski, T., Oleksik, V., Pepelnjak, T., Najm, S., Paniti, I., and Maji, K. (2021). Emerging Trends in Single Point Incremental Sheet Forming of Lightweight Metals. Metals, 11.10.3390/met11081188 ↗
6. Stamping formability of pure titanium sheets10.1016/j.jmatprotec.2005.05.004 ↗
7. An experimental investigation on thinning and formability in hybrid incremental sheet forming process10.1016/j.promfg.2019.02.011 ↗
8. Single point incremental forming: An assessment of the progress and technology trends from 2005 to 201510.1016/j.jmapro.2017.03.014 ↗
9. Asymmetric single point incremental forming of sheet metal10.1016/S0007-8506(07)60021-3 ↗
10. Review on strategies for geometric accuracy improvement in incremental sheet forming10.1007/s00170-019-03348-3 ↗
11. Formability improvement in single point incremental forming of truncated cone using a two-stage hybrid deformation strategy10.1007/s00170-017-1031-5 ↗
12. SPIF of tailored sheets to optimize thickness distribution along the shaped wall10.1016/j.promfg.2019.02.109 ↗
13. Additive-incremental forming hybrid manufacturing technique to improve customised part performance10.1016/j.jmapro.2018.12.008 ↗
14. Multi-objective optimization of quality characteristics in single point incremental forming process by response surface methodology
15. Raut, J., Marathe, S., and Raval, H. (2020). Numerical Investigation on Single Point Incremental Forming (SPIF) of Tailor Welded Blanks (TWBs). Advances in Simulation, Product Design and Development, Springer.10.1007/978-981-32-9487-5_4 ↗
16. Bambach, M., Sviridov, A., Weisheit, A., and Schleifenbaum, J.H. (2017). Case Studies on Local Reinforcement of Sheet Metal Components by Laser Additive Manufacturing. Metals, 7.10.3390/met7040113 ↗
17. Formability Analysis of Micro-Alloyed Sheet Metals Reinforced by Additive Manufacturing10.1016/j.promfg.2020.04.317 ↗
18. Material Properties of Ti6Al4V Parts Produced by Laser Metal Deposition10.1016/j.phpro.2012.10.056 ↗
19. Barro, Ó., Arias-González, F., Lusquiños, F., Comesaña, R., Del Val, J., Riveiro, A., Badaoui, A., Gómez-Baño, F., and Pou, J. (2020). Improved commercially pure titanium obtained by laser directed energy deposition for dental prosthetic applications. Metals, 11.10.3390/met11010070 ↗
20. Wissenbach, Laser additive manufacturing of metallic components: Materials, processes, and mechanisms10.1179/1743280411Y.0000000014 ↗
21. (2022, February 08). MatWeb, TIMET TIMETAL® 50A CP Titanium (ASTM Grade 2). Available online: http://www.matweb.com/search/datasheet.aspx?matguid=247af0c81c8a4a9da817bafa791d20bf&ckck=1.
22. (2022, March 31). AP&C, Advanced Powders. Available online: https://www.advancedpowders.com/powders/titanium/cp-ti2.
23. Effect of Laser Power and Scan Speed on Melt Pool Characteristics of Commercially Pure Titanium (CP-Ti)10.1007/s11665-017-2768-6 ↗
24. Lutjering, G., and Williams, J.C. (2007). Titanium, Springer. [2nd ed.].
25. On the evolution of microstructure and texture in commercial purity titanium during multiple passes of incremental equal channel angular pressing (I-ECAP)10.1016/j.msea.2017.05.040 ↗
26. Abnormal grain growth in commercially pure titanium during additive manufacturing with electron beam melting10.1016/j.mtla.2019.100281 ↗