Joining Strategies for Double-Sided Self-Pierce Riveting
Source abstract
Abstract
Double-sided self-pierce riveting (DSSPR) has been presenting itself as a proper alternative to self-pierce riveting (SPR) with many advantages for joining geometries of different thicknesses and cross-sections. To ensure its successful future industrial application, this paper presents a detailed comparison between different strategies to produce mechanical joints by means of the DSSPR process and discusses its performance and feasibility. Results show that the use of flat-bottom holes in both sheets provide interesting results, since they allow for a precise positioning of the tubular rivet in specific pre-defined locations, thus avoiding an incorrect joining procedure. This strategy tightens the tolerances of the process, while keeping a suitable level of destructive performance as demonstrated by the lap shear tests. Pre-riveting of the sheet has also been shown to produce suitable results in combination with or without a flat-bottom hole in the opposite sheet. This strategy comes at a cost of a slightly lower performance than that obtained with flat-bottom holes in both sheets, although the requirements of force and energy to complete the joining process are smaller. The conclusions of this research work are essential for selecting the joining strategy with DSSPR according to the requirements of the intended application.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Structural Load-Bearing Analysis · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
IDMEC, Instituto Superior Técnico, University of Lisbon, Av. Rovisco Pais, 1049-001 Lisbon, Portugal
Funding
IDMEC
References (22)
Show source-provided references
1. (2003). Standard No. DIN 8593-5:2003-09. Classification, Subdivision, Terms and Definitions.
2. Joining by forming technologies: Current solutions and future trends10.1007/s12289-022-01674-8 ↗
3. Review on mechanical joining by plastic deformation10.1016/j.jajp.2022.100113 ↗
4. Mechanical joining in versatile process chains10.1007/s11740-022-01125-y ↗
5. Self-piercing riveting—A review10.1007/s00170-017-0156-x ↗
6. Effects of factors on physical attributes of self-piercing riveted joints10.1179/174329306X131866 ↗
7. Strength and Failure of Self-Piercing Riveted Aluminum and Steel Sheet Joints: Multi-axial Experiments and Modeling10.1016/j.jajp.2022.100107 ↗
8. Influence of edge distance on quality and static behaviour of self-piercing riveted aluminium joints10.1016/j.matdes.2011.07.046 ↗
9. Influence of sheet thickness on fatigue behavior and fretting of self-piercing riveted joints in aluminum alloy 505210.1016/j.matdes.2015.08.121 ↗
10. Failure behaviour of SPR joints after salt spray test10.1016/j.engstruct.2014.10.020 ↗
11. Influence of aluminium sheet surface modification on the self-piercing riveting process and the joint static lap shear strength10.1007/s00170-017-0710-6 ↗
12. Joining of multi-material structures using a versatile self-piercing riveting process10.1007/s11740-022-01151-w ↗
13. Mechanical properties and fatigue failure mechanisms of purely self-piercing riveted (SPR) and hybrid (SPR-bonded) joints under salt spray environment10.1016/j.jmrt.2022.08.024 ↗
14. An Overview of Self-piercing Riveting Process with Focus on Joint Failures, Corrosion Issues and Optimisation Techniques10.1186/s10033-020-00526-3 ↗
15. Method of joining sheets by using new type of rivets10.1016/S0924-0136(01)00519-2 ↗
16. Double-sided self-pierce riveting10.1007/s00170-020-05503-7 ↗
17. Revisiting the design of the rivet chamfered ends in double-sided self-pierce riveting10.1016/j.tws.2022.109375 ↗
18. On the applicability limits of double-sided self-pierce riveting
19. Double-sided self-pierce riveting of dissimilar materials10.1007/s00170-021-07426-3 ↗
20. Double-sided self-pierce riveting with flat-bottom holes: A feasibility study10.1007/s11740-021-01082-y ↗
21. Nielsen, C.V., Zhang, W., Alves, L.M., Bay, N., and Martins, P.A.F. (2013). Modeling of Thermo-Electro-Mechanical Manufacturing Processes, Springer.10.1007/978-1-4471-4643-8 ↗
22. Banabic, D. (2010). Sheet Metal Forming Processes: Constitutive Modelling and Numerical Simulation, Springer.10.1007/978-3-540-88113-1 ↗