journal article·2023-11-14Open access

Exploring the Utilization of PHC Pile Waste Concrete as Filler in Asphalt Mastics

Botao Tu, Xinkui Yang, Shi Xu, Xuhui Liang, Chen Liu, Jian Jiang, Lulu Fan, Liangliang Tu

Materials· Volume 16· Issue 22

Abstract

Using solid waste to replace limestone filler in asphalt concrete can not only reduce the cost of road construction, but also improve the utilization rate of solid waste. In this study, PHC pile waste concrete (PPWC) was innovatively used to replace limestone filler in asphalt mixture and its effect on the physical and rheological properties of asphalt mastics was studied. Firstly, PPWC was ground into filler particles with a diameter less than 0.075 mm. The physical properties, particle characteristics and chemical composition of PPWC filler and limestone filler were compared. Asphalt mastics were prepared with different filler-asphalt volume ratios (20%, 30% and 40%) and the physical properties, high-temperature rheological properties and low-temperature cracking resistance of asphalt mastics were tested. The experimental results showed that the surface of PPWC filler is rougher and has lower density and smaller particle size than limestone filler. When the filler content is the same, PPWC filler asphalt mastics have lower penetration and ductility, higher softening point than limestone filler asphalt mastics, and the viscosity of PPWC filler asphalt mastics is more sensitive than limestone filler asphalt mastics. PPWC filler asphalt mastics demonstrated superior high-temperature stability, but poorer low-temperature cracking resistance compared to limestone filler asphalt mastics. In conclusion, PPWC fillers can be used to replace limestone fillers in asphalt mixtures. The finding of this study will provide a new solution for the construction of eco-friendly roads.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Concrete and Cement Materials Research · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Guangdong Hongye Building Materials Technology Co., Ltd., Yunfu 527121, China

State Key Laboratory of Silicate Materials for Architectures, Wuhan University of Technology, Wuhan 430070, China

School of Civil Engineering and Architecture, Wuhan University of Technology, Luoshi Road 122, Wuhan 430070, China

Faculty of Civil Engineering and Geosciences, Delft University of Technology, Stevinweg 1, 2628 CN Delft, The Netherlands

Shenzhen Sez Construction Group Co., Ltd., Shenzhen 518034, China

Funding

National Natural Science Foundation of China · Hubei Science and Technology Innovation Talent and Service Project

References (54)

Show source-provided references
1. Studies of nano-SiO2 and subsequent water curing on enhancing the frost resistance of autoclaved PHC pipe pile concrete10.1016/j.jobe.2023.106209 ↗
2. Corrosion initiation life of laterally loaded PHC pipe piles served in marine environment: Theoretical prediction and analysis10.1016/j.conbuildmat.2021.123457 ↗
3. Durability and microstructure of steam cured and autoclaved PHC pipe piles10.1016/j.conbuildmat.2019.03.166 ↗
4. Study on bearing behavior and Q-s curve model of rock-socketed PHC pipe piles based on ultimate load tests
5. Shaft capacity of prestressed high strength concrete (PHC) pile-cemented soil column embedded in clayey soil10.1016/j.sandf.2021.05.006 ↗
6. Recycling prestressed concrete pile waste to produce green self-compacting concrete10.1016/j.jmrt.2023.04.101 ↗
7. Development of blending model for RAP and virgin asphalt in recycled asphalt mixtures via a micron-Fe3O4 tracer10.1016/j.jclepro.2022.135407 ↗
8. Characterization of asphalt bitumens and asphalt concretes modified with carbon powder
9. Fatigue damage investigation on asphalt concrete under cyclic freeze–thaw using a combined energy and viscoelasticity method10.1016/j.conbuildmat.2023.131707 ↗
10. Low-temperature fracture behavior of railway asphalt concretes under semi-circular bending: Experimental and numerical investigation10.1016/j.conbuildmat.2023.132990 ↗
11. Evaluation of asphalt concrete’s fatigue behavior using cyclic semi-circular bending test10.1016/j.conbuildmat.2023.132772 ↗
12. Comprehensive modification of emulsified asphalt on improving mechanical properties of crumb rubber concrete10.1016/j.conbuildmat.2023.130555 ↗
13. Perspectives on the utilization of reclaimed asphalt pavement in concrete pavement construction: A critical review
14. Li, J., Yu, J., Wu, S., and Xie, J. (2022). The Mechanical Resistance of Asphalt Mixture with Steel Slag to Deformation and Skid Degradation Based on Laboratory Accelerated Heavy Loading Test. Materials, 15.10.3390/ma15030911 ↗
15. Preparation, thermochromic properties and temperature controlling ability of novel pellets in ultra-thin wearing course10.1016/j.conbuildmat.2023.131797 ↗
16. Rheological properties of asphaltene-modified asphalt binder and mastic10.1016/j.pce.2023.103422 ↗
17. Micromechanics prediction of dynamic modulus for asphalt mastic considering filler distribution characteristic: A new perspective10.1016/j.conbuildmat.2022.129916 ↗
18. Preparation of an eco-friendly de-icing filler and its effects on the performance of different asphalt mastic10.1016/j.conbuildmat.2022.129967 ↗
19. Performance characterization and enhancement mechanism of recycled asphalt mixtures involving high RAP content and steel slag10.1016/j.jclepro.2022.130484 ↗
20. Influence of iron tailing filler on rheological behavior of asphalt mastic10.1016/j.conbuildmat.2022.129047 ↗
21. Influence of the physical and chemical characteristics of sediment fillers on the properties of mastic asphalt10.1016/j.powtec.2023.118393 ↗
22. Synthesis of environmental-curable CO2-based polyurethane and its enhancement on properties of asphalt binder10.1016/j.jclepro.2022.135576 ↗
23. Performance and VOCs emission inhibition of environmentally friendly rubber modified asphalt with UiO-66 MOFs10.1016/j.jclepro.2022.135633 ↗
24. Use of Hydrated Ladle Furnace Slag as a filler substitute in asphalt mastics: Rheological analysis of filler/bitumen interaction10.1016/j.conbuildmat.2022.127370 ↗
25. Sustainable asphalt mastics made up recycling waste as filler10.1016/j.jenvman.2021.113826 ↗
26. The influence of filler type and gradation on the rheological performance of mastics10.1080/14680629.2018.1428216 ↗
27. Evaluation of fatigue performance of asphalt mastics composed of nano hydrated lime filler10.1016/j.conbuildmat.2020.121322 ↗
28. Utilization of red mud as an alternative mineral filler in asphalt mastics to replace natural limestone powder10.1016/j.conbuildmat.2019.117821 ↗
29. Characterization of thermal, high-temperature rheological and fatigue properties of asphalt mastic containing fly ash cenosphere10.1016/j.conbuildmat.2019.117345 ↗
30. Environmental performance and functional analysis of chip seals with recycled basic oxygen furnace slag as aggregate10.1016/j.jhazmat.2020.124441 ↗
31. Robustness of self-compacting concrete incorporating bone china ceramic waste powder along with granite cutting waste for sustainable development10.1016/j.jclepro.2022.132969 ↗
32. Influence of concentration and packing of filler particles on the stiffening effect and shearing behaviour of asphalt mastic10.1016/j.conbuildmat.2021.123660 ↗
33. Utilization of iron ore tailing as an alternative mineral filler in asphalt mastic: High-temperature performance and environmental aspects10.1016/j.jclepro.2021.130318 ↗
34. Effect of volcanic ash filler on thermal viscoelastic property of SBS modified asphalt mastic10.1016/j.conbuildmat.2018.09.101 ↗
35. Characteristics of calcareous sand filler and its influence on physical and rheological properties of asphalt mastic10.1016/j.conbuildmat.2021.124112 ↗
36. Analyzing the effect of waste jarosite as an alternative filler on the engineering properties of asphalt mixes10.1016/j.conbuildmat.2020.121466 ↗
37. Potential improvements in montmorillonite-nanoclay-modified Cold-Mix Asphalt
38. Incorporation of Sugarcane Bagasse Ash to investigate the mechanical behavior of Stone Mastic Asphalt10.1016/j.conbuildmat.2022.129089 ↗
39. The effect of retreated coal wastes as filler on the performance of asphalt mastics and mixtures10.1016/j.conbuildmat.2019.01.088 ↗
40. Effects of zeolite on rheological properties of asphalt materials and asphalt-filler interaction ability10.1016/j.conbuildmat.2023.131300 ↗
41. Evaluating the properties of zinc production wastes as filler and their effects on asphalt mastic10.1016/j.conbuildmat.2020.120748 ↗
42. Laboratory evaluation of stone mastic asphalt containing amorphous carbon powder as filler material10.1016/j.conbuildmat.2020.118280 ↗
43. Investigation of rutting, fracture and thermal cracking behavior of asphalt mastic containing basalt and hydrated lime fillers10.1016/j.conbuildmat.2017.03.032 ↗
44. Upcycling waste phosphogypsum as an alternative filler for asphalt pavement10.1016/j.jclepro.2023.138332 ↗
45. Creep and fatigue properties of asphalt mastic with steel slag powder filler
46. Usage of two biomass ashes as filler in hot mix asphalt10.1016/j.conbuildmat.2018.03.102 ↗
47. Performance of asphalt mortar with recycled concrete powder under different filler-to-asphalt weight ratios
48. (2011). Standard Test Methods of Bitumen and Bituminous Mixtures for Highway Engineering. (Standard No. JTG E20-2011).
49. (2005). Test Methods of Aggregate for Highway Engineering. (Standard No. JTG E42-2005).
50. Recycling of bone china ceramic waste as cement replacement to produce sustainable self-compacting concrete10.1016/j.istruc.2022.01.019 ↗
51. Effects of the morphological characteristics of mineral powder fillers on the rheological properties of asphalt mastics at high and medium temperatures10.1016/j.powtec.2019.03.014 ↗
52. Multi-scale microstructure quantitative characterization and anti-erosion performance of PHC pipe pile10.1016/j.conbuildmat.2023.133464 ↗
53. Innovative use of industrially produced steel slag powders in asphalt mixture to replace mineral fillers10.1016/j.jclepro.2022.131124 ↗
54. (1998). Standard Specification for Performance Graded Asphalt Binder (Standard No. AASHTO MP1-1998).