Fabrication of Ceramic Microchannels with Periodic Corrugated Microstructures as Catalyst Support for Hydrogen Production via Diamond Wire Sawing
Source abstract
Abstract
Hydrogen energy is the clean energy with the most potential in the 21st century. The microchannel reactor for methanol steam reforming (MSR) is one of the effective ways to obtain hydrogen. Ceramic materials have the advantages of high temperature resistance, corrosion resistance, and high mechanical strength, and are ideal materials for preparing the catalyst support in microchannel reactors. However, the structure of ceramic materials is hard and brittle, and the feature size of microchannel is generally not more than 1 mm, which is difficult to process using traditional processing methods. Diamond wire saw processing technology is mainly used in the slicing of hard and brittle materials such as sapphire and silicon. In this paper, a microchannel with a periodic corrugated microstructure was fabricated on a ceramic plate using diamond wire sawing, and then as a catalyst support when used in a microreactor for MSR hydrogen production. The effects of wire speed and feed speed on the amplitude and period size of the periodic corrugated microstructure were studied using a single-factor experiment. The microchannel surface morphology was observed via SEM and a 3D confocal laser microscope under different processing parameters. The microchannel samples obtained under different processing parameters were supported by a multiple impregnation method. The loading strength of the catalyst was tested via a strong wind purge experiment. The experimental results show that the periodic corrugated microstructure can significantly enhance the load strength of the catalyst. The microchannel catalyst support with the periodic corrugated microstructure was put into the microreactor for a hydrogen production experiment, and a good hydrogen production effect was obtained. The experimental results have a positive guiding effect on promoting ceramic materials as the microchannel catalyst support for the development of hydrogen energy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Catalytic Processes in Materials Science · Lattice Boltzmann Simulation Studies · Heat Transfer and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Pen-Tung Sah Institute of Micro-Nano Science and Technology, Xiamen University, Xiamen 361005, China
Funding
National Natural Science Foundation of China · Science and Technology Major Program of Fujian Province, China · Major Science and Technology Plan of Xiamen City, Fujian, China
References (41)
Show source-provided references
1. Synergistic enhanced catalysis of micro-reactor with nano MnO2/ZIF-8 immobilized in membrane pores by flowing synthesis10.1016/j.memsci.2021.119233 ↗
2. Facile synthesis behavior and CO2 adsorption capacities of Zn-based metal organic framework prepared via a microchannel reactor10.1016/j.cej.2022.140078 ↗
3. Solvent extraction with a three-dimensional reticulated hollow-strut SiC foam microchannel reactor10.1016/j.cjche.2021.05.018 ↗
4. Lattice-structured SiC ceramics obtained via 3D printing, gel casting, and gaseous silicon infiltration sintering10.1016/j.ceramint.2021.11.193 ↗
5. Ceramic microchannel reactors with channel sizes less than 100 μm prepared by a mesh-assisted phase-inversion process10.1016/j.ceramint.2021.05.271 ↗
6. Porous copper fiber sintered felts with surface microchannels for methanol steam reforming microreactor for hydrogen production10.1016/j.ijhydene.2019.01.141 ↗
7. Functional catalytic membrane development: A review of catalyst coating techniques10.1016/j.cis.2020.102207 ↗
8. Numerical modeling of microchannel reactor with porous surface microstructure based on fractal geometry10.1016/j.ijhydene.2018.10.135 ↗
9. Development of a flat membrane microchannel packed-bed reactor for scalable aerobic oxidation of benzyl alcohol in flow10.1016/j.cej.2018.10.023 ↗
10. SiC/HfB2-based ceramic/SiC multilayer coating to protect C/C composites against oxidation at medium and high temperatures for long-life service10.1016/j.corsci.2022.110299 ↗
11. High-temperature stability and oxidation behavior of SiOC/HfO2 ceramic nanocomposite in air10.1016/j.corsci.2020.108866 ↗
12. Lattice Boltzmann simulation of drop splitting in a fractal tree-like microchannel10.1016/j.ces.2021.117277 ↗
13. Pressure drop model of gas-liquid flow with mass transfer in tree-typed microchannels10.1016/j.cej.2020.125340 ↗
14. Heat transfer and flow characteristics of varying curvature wavy microchannels10.1016/j.ijthermalsci.2022.108096 ↗
15. Pressureless spark plasma sintering of alumina micro-channel part produced by micro powder injection molding10.1016/j.scriptamat.2010.10.016 ↗
16. Powder injection molding of silicon carbide: Processing issues10.1016/j.mprp.2016.02.048 ↗
17. Ceramic microreactors for heterogeneously catalysed gas-phase reactions10.1039/b403361b ↗
18. Enhancement in mixing efficiency by ridges in straight and meander microchannels10.1016/j.cep.2020.108217 ↗
19. Experimental analysis of fiber laser milling process for generating microchannel on zirconia (ZrO2)10.1016/j.matpr.2019.07.287 ↗
20. Performance evaluation of high concentration photovoltaic cells cooled by microchannels heat sink with serpentine reentrant microchannels10.1016/j.apenergy.2021.118478 ↗
21. Structural design and performance research of methanol steam reforming microchannel for hydrogen production based on mixing effect10.1016/j.ijhydene.2020.05.190 ↗
22. Whole ceramic-like microreactors from inorganic polymers for high temperature or/and high pressure chemical syntheses10.1039/C3LC51191J ↗
23. Machinability study of biolox forte ceramic by milling microchannels using rotary ultrasonic machining10.1016/j.jmapro.2019.05.031 ↗
24. Effect of pre-calcined ceramic powders at different temperatures on Ni-YSZ anode-supported SOFC cell/stack by low pressure injection molding10.1016/j.ceramint.2019.06.270 ↗
25. Dust generation in vibrated cohesive powders
26. Effect mechanism of multiple obstacles on non-Newtonian flow in ceramic 3D printing (arcuate elements)10.1016/j.ceramint.2021.08.370 ↗
27. Laser micro-milling of microchannel on copper sheet as catalyst support used in microreactor for hydrogen production10.1016/j.ijhydene.2014.01.041 ↗
28. Investigation of double-layered wavy microchannel heatsinks utilizing porous ribs with artificial neural networks10.1016/j.icheatmasstransfer.2022.105984 ↗
29. Flow resistance and convective heat transfer by elastic turbulence in 1D/2D/3D geometries10.1016/j.ijthermalsci.2022.107512 ↗
30. Surface integrity studies on ZrB2 and graphene reinforced ZrB2 ceramic matrix composite in EDM process10.1016/j.cirpj.2022.04.010 ↗
31. Feasibility and tool performance of ultrasonic vibration-assisted milling-grinding SiCf/SiC ceramic matrix composite10.1016/j.jmrt.2022.06.063 ↗
32. Manufacturing of a ceramic groove part based on additive and subtractive technologies10.1016/j.ceramint.2020.08.184 ↗
33. Characteristics of proton exchange membrane fuel cell considering “dot matrix” gas distribution zones and waveform staggered flow field with cooling channels10.1016/j.enconman.2022.115881 ↗
34. Three-dimensional multi-phase simulation of different flow fields with cooling channel in proton exchange membrane fuel cell10.1016/j.ijhydene.2022.08.286 ↗
35. Additive manufacturing of advanced ceramic materials10.1016/j.pmatsci.2020.100736 ↗
36. Sawing characteristics of diamond wire cutting sapphire crystal based on tool life cycle10.1016/j.ceramint.2021.06.070 ↗
37. Influence of silicon anisotropy on surface shape deviation of wafer by diamond wire saw10.1016/j.mssp.2021.105981 ↗
38. Influences of hard inclusions on processing stress in diamond multi-wire sawing multi-crystalline silicon10.1016/j.mssp.2022.106602 ↗
39. Analysis of sawing characteristics of fine diamond wire slicing multicrystalline silicon10.1016/j.diamond.2021.108708 ↗
40. 3D printed hydrogel/wesselsite-PCL composite scaffold with structural change from core/shell fibers to microchannels for enhanced bone regeneration10.1016/j.compositesb.2022.110264 ↗
41. A review of 3D printed porous ceramics10.1016/j.jeurceramsoc.2022.02.039 ↗