journal article·2024-07-12Open access

Corrosion Behavior of Ferritic 12Cr ODS and Martensitic X46Cr13 Steels in Nitric Acid and Sodium Chloride Solutions

Krzysztof Nowik, Rafał Zybała, Bogna Sztorch, Zbigniew Oksiuta

Materials· Volume 17· Issue 14

Abstract

This paper presents corrosion resistance results of a 12Cr ferritic ODS steel (Fe-12Cr-2W-0.5Zr-0.3Y2O3) fabricated via a powder metallurgy route as a prospective applicant for fuel cladding materials. In a spent nuclear fuel reprocessing facility, nitric acid serves as the primary solvent in the PUREX method. Therefore, fundamental immersion and electrochemical tests were conducted in various nitric acid solutions to evaluate corrosion degradation behavior. Additionally, polarization tests were also performed in 0.61 M of sodium chloride solutions (seawater-like atmosphere) as a more general, all-purpose procedure that produces valid comparisons for most metal alloys. For comparison, martensitic X46Cr13 steel was also examined under the same conditions. In general, the corrosion resistance of the 12Cr ODS steel was better than its martensitic counterpart despite a lower nominal chromium content. Potentiodynamic polarization plots exhibited a lower corrosion current and higher breakdown potentials in chloride solution in the case of the ODS steel. It was found that the corrosion rate during immersion tests was exceptionally high in diluted (0.1–3 M) boiling nitric acid media, followed by its sharp decrease in more concentrated solutions (>4 M). The results of the polarization plots also exhibited a shift toward more noble corrosion potential as the concentrations increased from 1 M to 4 M of HNO3. The results on corrosion resistance were supported by LSCM and SEM observations of surface topology and corrosion products.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Fusion materials and technologies · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute of Mechanical Engineering, Faculty of Mechanical Engineering, Białystok University of Technology, Wiejska 45C, 15-351 Białystok, Poland

Łukasiewicz Research Network—Institute of Microelectronics and Photonics, Al. Lotników 32/46, 02-668 Warsaw, Poland

Centre for Advanced Technologies, Adam Mickiewicz University in Poznań, Uniwersytetu Poznańskiego 10, 61-614 Poznań, Poland

Institute of Biomedical Engineering, Faculty of Mechanical Engineering, Białystok University of Technology, Wiejska 45C, 15-351 Białystok, Poland

Funding

Ministry of Science and Higher Education of Poland

References (64)

Show source-provided references
1. Holland, H.D., and Turekian, K.K. (2014). Treatise on Geochemistry, Elsevier Science. [2nd ed.].
2. Cottis, B., Graham, M., Lindsay, R., Lyon, S., Richardson, T., Scantlebury, D., and Stott, H. (2010). Shreir’s Corrosion, Elsevier Science. [4th ed.].
3. Konings, R.J.M., and Stoller, R.E. (2020). Comprehensive Nuclear Materials, Elsevier. [2nd ed.].
4. Orientation dependence of corrosion resistance of a near–alpha Ti35 alloy applied in nuclear industry10.1016/j.jnucmat.2022.153873 ↗
5. Long–term storage of spent nuclear fuel10.1038/nmat4226 ↗
6. Nash, K.L., and Lumetta, G.J. (2011). Advanced Separation Techniques for Nuclear Fuel Reprocessing and Radioactive Waste Treatment, Woodhead Publishing.10.1533/9780857092274 ↗
7. Recent Developments in the Purex Process for Nuclear Fuel Reprocessing: Complexant Based Stripping for Uranium/Plutonium Separation10.2533/000942905777675327 ↗
8. Materials development and corrosion problems in nuclear fuel reprocessing plants10.1016/j.pnucene.2005.07.001 ↗
9. The stress corrosion cracking performance of pure zirconium and zirconium alloys in highly oxidizing nitric acid10.1016/0010-938X(95)00166-H ↗
10. Nowik, K., Zybała, R., and Oksiuta, Z. (2023). Formation and Microstructural Evolution of Ferritic ODS Steel Powders during Mechanical Alloying. Materials, 16.10.3390/ma16020765 ↗
11. Influence of Al addition on the microstructure and mechanical properties of Zr-containing 9Cr-ODS steel10.1016/j.jmrt.2021.05.112 ↗
12. Recent Developments in Irradiation-Resistant Steels10.1146/annurev.matsci.38.060407.130315 ↗
13. Corrosion behavior of ODS steels with several chromium contents in hot nitric acid solutions10.1016/j.jnucmat.2017.07.008 ↗
14. Oxidation kinetics of Haynes 230 alloy in air at temperatures between 650 and 850 °C10.1016/j.jpowsour.2005.09.065 ↗
15. Oxidation of ferritic stainless steel interconnects: Thermodynamic and kinetic assessment10.1016/j.jpowsour.2010.09.099 ↗
16. Influence of microstructure and surface treatment on the corrosion resistance of martensitic stainless steels 1.4116, 1.4034, and 1.402110.1002/maco.201307276 ↗
17. Kubaschewski, O., and Hopkins, B.E. (1953). Oxidation of Metals and Alloys, Butterworths Scientific Publications.
18. Effects of Carbon Allotropic Forms on Microstructure and Thermal Properties of Cu-C Composites Produced by SPS10.1007/s11665-015-1851-0 ↗
19. Brnic, J., Krscanski, S., Lanc, D., Brcic, M., Turkalj, G., Canadija, M., and Niu, J. (2017). Analysis of the Mechanical Behavior, Creep Resistance and Uniaxial Fatigue Strength of Martensitic Steel X46Cr13. Materials, 10.10.3390/ma10040388 ↗
20. Influence of solution annealing temperature and cooling medium on microstructure, hardness and corrosion resistance of martensitic stainless steel X46Cr1310.1002/maco.201408081 ↗
21. (2012). Standard Guide for Laboratory Immersion Corrosion Testing of Metals (Standard No. ASTM G31-21a).
22. Exact calculation of corrosion rates by the weight–loss method10.1017/exp.2022.5 ↗
23. (2021). Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5% Sodium Chloride Solution (Standard No. ASTM G44-21).
24. Bard, A.J., and Faulkner, L.R. (2001). Electrochemical Methods–Fundamentals and Applications, Wiley. [2nd ed.].
25. Electrochemical polarization: I. A theoretical analysis of the shape of polarization curves10.1149/1.2428496 ↗
26. The Stern–Geary and related methods for determining corrosion rates10.1071/CH9750243 ↗
27. Niinomi, M. (2010). Metals for Biomedical Devices, Woodhead Publishing Limited. Chapter 4.10.1533/9781845699246 ↗
28. The determination of Tafel slopes by the successive approximation method10.1016/0010-938X(95)00009-9 ↗
29. Whole powder pattern modelling10.1107/S0108767301021298 ↗
30. The crystal structure of Cr23C610.1107/S0567740872007526 ↗
31. Evolution of Crystallographic Structure of M23C6 Carbide Under Thermal Aging of P91 Steel10.1007/s11665-019-03935-1 ↗
32. Effect of alloying elements on the contact resistance and the passivation behaviour of stainless steels10.1016/S0010-938X(01)00107-X ↗
33. Corrosion resistance of 9–15% Cr ODS steels and its comparison with austenitic stainless steel10.4028/www.scientific.net/AMR.794.575 ↗
34. The surface characterization and corrosion resistance of 11% Cr ferritic/martensitic and 9–15% Cr ODS steels for nuclear fuel reprocessing application10.1007/s10008-013-2165-5 ↗
35. Influence of dispersoids on corrosion behavior of oxide dispersion strengthened 18Cr steels made by high energy milling10.1007/s11665-015-1859-5 ↗
36. Corrosion Resistance of 13% Chromium Steels as Influenced by Tempering Treatments10.1179/000705976798320124 ↗
37. Influence of the heat treatment on the corrosion resistance of the martensitic stainless steel type AISI 42010.1023/A:1025179128333 ↗
38. Pitting corrosion of martensitic cutlery steels10.1016/0376-4583(80)90075-8 ↗
39. Quantitative analysis of Cr–depleted zone morphology in low carbon martensitic stainless steel using Fe–(S)TEM10.1016/j.corsci.2007.08.004 ↗
40. Microstructure and mechanical behavior of ODS and non–ODS Fe–14Cr model alloys produced by spark plasma sintering10.1016/j.jnucmat.2013.01.331 ↗
41. Microstructure characterization and tensile properties of hot isostatic pressed China ultrahigh strength steel10.1016/j.jmrt.2020.10.013 ↗
42. Impact of the use of the ferritic/martensitic ODS steels cladding on the fuel reprocessing PUREX process10.1016/j.jnucmat.2011.11.005 ↗
43. Corrosion resistance of 9% Cr oxide dispersion strengthened steel in different electrolytic media10.5006/0839 ↗
44. Nature of the Passive Film on Iron in Concentrated Nitric Acid10.1149/1.2429913 ↗
45. Corrosion studies of stainless steel 304 L in nitric acid in the presence of uranyl nitrate: Effect of temperature and nitric acid concentration10.1007/s42452-020-2273-7 ↗
46. Corrosion behaviour of Al-containing high Cr ferritic oxide dispersion strengthened steel in nitric acid environment10.1016/j.jnucmat.2020.152120 ↗
47. The corrosion resistance and passive film compositions of 12% Cr and 15% Cr oxide dispersion strengthened steels in nitric acid media10.1016/j.corsci.2013.10.015 ↗
48. The dissolution behaviour of iron, chromium, molybdenum and copper from pure metals and from ferritic stainless steels10.1016/0010-938X(87)90060-6 ↗
49. Chen, L., Xu, S., Schroer, C., Jia, H., Ruan, Z., Qin, B., Zhou, Z., and Long, B. (2023). Comparison of Corrosion Behavior of T91, 9Cr and 9CrAl ODS Steels in Liquid Pb. Materials, 16.10.3390/ma16062295 ↗
50. Structure, Mechanical Properties, and Corrosion Resistance of the CrCuFeNiMo0.3 High-Entropy Alloy Prepared by Powder Metallurgy10.1007/s11106-022-00278-w ↗
51. On the relationship between grain boundary character distribution and intergranular corrosion10.1016/S1359-6462(97)00018-3 ↗
52. Corrosion behaviors of ODS-FeCrAl in oxygen-saturated lead-bismuth eutectic at 550 °C: Effects of grain boundaries and minor elements10.1016/j.jnucmat.2023.154710 ↗
53. Electrochemical Behavior and Surface Characteristics of Pure Titanium During Corrosion in Simulated Desulfurized Flue Gas Condensates10.1149/2.1321809jes ↗
54. Superior Corrosion Resistance of Ti-Al-Zr Alloy in Aggressive Nitric Acid Environments10.1007/s11665-020-05300-z ↗
55. Cottis, B., Graham, M., Lindsay, R., Lyon, S., Richardson, T., Scantlebury, D., and Stott, H. (2010). Shreir’s Corrosion, Elsevier Science. [4th ed.].
56. Corrosion mechanisms of austenitic stainless steels in nitric media used in reprocessing plants10.1016/j.jnucmat.2007.10.017 ↗
57. Capacitance behaviour of passive films on ferritic and austenitic stainless steel10.1016/j.corsci.2004.07.002 ↗
58. Thermodynamic Assessment of the Effect of Chromium and Molybdenum on the Passivability of Nickel-Base Alloys10.1023/B:PROM.0000007851.48111.59 ↗
59. Corrosion and high temperature compressive strength behaviour of 17Cr ferritic ODS steel with addition of aluminium through vacuum hot pressing
60. The composition of the boundary region of MnS inclusions in stainless steel and its relevance in triggering pitting corrosion10.1016/j.corsci.2004.05.023 ↗
61. Nucleation and Repassivation of Corrosion Pits for Pitting on Iron and Nickel10.1002/maco.19760271106 ↗
62. Pitting Corrosion of Metals: A Review of the Critical Factors10.1149/1.1838615 ↗
63. Yang, L., Qian, H., and Kuang, W. (2022). Corrosion Behaviors of Heat–Resisting Alloys in High Temperature Carbon Dioxide. Materials, 15.10.3390/ma15041331 ↗
64. The observation of stress effects during the high temperature oxidation of iron10.1007/BF00540812 ↗