journal article·2024-12-21Open access

Propagation of a Fatigue Crack Through a Hole

Diogo Neto, Joel Jesus, Ricardo Branco, Edmundo Sérgio, Fernando Antunes

Materials· Volume 17· Issue 24

Abstract

The stop-hole technique is a well-known strategy to extend the fatigue life of cracked components. The ability to estimate fatigue life after the hole is important for safety reasons. The objective here is to develop strategies for the accurate prediction of initiation and propagation life ahead of the stop-hole. Experimental work was developed in a Compact-Tension (CT) specimen made of 7050-T7451 aluminium alloy and with a 3 mm diameter hole. A total number of 625,000 load cycles were required to re-initiate the crack after the hole. Crack initiation life after the hole was estimated using the Theory of Critical Distances combined with the Smith–Watson–Topper parameter. A value of a0 = 31.83 µm was obtained for El Haddad parameter, which was used to define the critical distance. The predicted life was found to be only 4% lower than the experimental value. The fatigue crack growth (FCG) rate was calculated using a node release strategy, assuming that cyclic plastic deformation is the main damage mechanism and that cumulative plastic strain is the crack driving parameter. A good agreement was found between the numerical predictions of da/dN and the experimental results. The main result, however, is the proposed methodology, which allows predicting the initiation and propagation lives in notched components.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Probabilistic and Robust Engineering Design · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

University Coimbra, Centre for Mechanical Engineering, Materials and Processes (CEMMPRE), Department of Mechanical Engineering, 3030-788 Coimbra, Portugal

Funding

Portuguese Foundation of Science and Technology (FCT) · FCT for the PhD grant

References (55)

Show source-provided references
1. Retardation and Repair of Fatigue Cracks by Adhesive Infiltration10.1111/j.1460-2695.1997.tb00292.x ↗
2. A model for evaluating the effect of fatigue crack repair by the infiltration method10.1046/j.1460-2695.2000.00347.x ↗
3. Effect of artificial closure materials on crack growth retardation10.1016/S0013-7944(97)00180-X ↗
4. Deposition of plating metals to improve crack growth life10.1016/S0142-1123(00)00084-0 ↗
5. Mixed mode fracture in an inclined center crack repaired by composite patching10.1016/j.compstruct.2006.08.013 ↗
6. Investigation of a cracked thick aluminium panel repaired with a bonded composite patch10.1016/S0013-7944(99)00032-6 ↗
7. Repair efficiency in fatigue-cracked aluminium components reinforced with boron/epoxy patches10.1111/j.1460-2695.1993.tb00117.x ↗
8. Penetration and Defect Formation in High-Current Arc Welding
9. Tensile fracture behavior in CO2 laser beam welds of 7075-T6 aluminum alloy10.1016/j.matdes.2004.02.017 ↗
10. The effects of overloads in fatigue crack growth10.1016/0142-1123(91)90479-I ↗
11. On the mechanisms and behaviour of overload retardation in AISI 304 stainless steel10.1016/0142-1123(93)90175-P ↗
12. Crack growth arresting property of a hole and Brinell-type dimple10.1111/j.1460-2695.1996.tb00930.x ↗
13. Retardation of fatigue crack propagation by indentation technique10.1016/S0308-0161(02)00096-0 ↗
14. Effect of ring indentation on fatigue crack growth in an aluminum plate10.1016/j.ijfatigue.2003.08.011 ↗
15. Experimental and numerical evaluation of crack arresting capability due to a dimple10.1115/1.1865185 ↗
16. Application of indentation as a retardation mechanism for fatigue crack growth10.1016/j.ijfatigue.2011.09.012 ↗
17. Expansion of cracked fastener holes as a measure for extension of lifetime to repair10.1016/0013-7944(87)90062-2 ↗
18. Experimental investigation on the effects of cold expansion of fastener holes10.1046/j.1460-2695.1998.00430.x ↗
19. Fatigue life estimation after crack repair in 6005 AT-6 aluminium alloy using the cold expansion hole technique10.1046/j.1460-2695.2000.00356.x ↗
20. Effect of water and paint coatings on the magnitude of laser-generated shocks10.1016/0030-4018(76)90327-8 ↗
21. Laser shock peening on fatigue behavior of 2024-T3 Al alloy with fastener holes and stop holes10.1016/S0921-5093(00)01277-6 ↗
22. Emerald Article: Retained residual stress profiles in a laser shock peened and shot-peened nickel base superalloy subject to thermal exposure10.1108/17579861111108590 ↗
23. Compressive residual stress introduced by shot peening10.1016/S0924-0136(97)00213-6 ↗
24. Growth and retardation of physically short fatigue cracks in an aircraft Al-alloy after shot peening10.1016/j.proeng.2011.04.562 ↗
25. Numerical analysis for effects of shot peening on fatigue crack growth10.1016/j.ijfatigue.2012.02.010 ↗
26. Spot Heating Induced Fatigue Crack Growth Retardation10.1016/S0308-0161(02)00019-4 ↗
27. A study on spot heating induced fatigue crack growth retardation10.1111/j.1460-2695.2005.00901.x ↗
28. The Effects of Simultaneous Overload and Spot Heating on Crack Growth Retardation in Fatigue10.1016/0013-7944(93)90098-D ↗
29. Stop drilling procedure for fatigue life improvement10.1016/j.ijfatigue.2004.04.009 ↗
30. On the prediction of the residual fatigue life of cracked structures repaired by the stop-hole method10.1016/j.ijfatigue.2009.09.011 ↗
31. (2012). Aviation Maintenance Technician Handbook—Airframe, Vol. 1, U.S. Department of transportation, Federal Aviation Administration, Flight Standards Service. Chapter 04.
32. Miki, C. (2025). Retrofitting Engineering for Fatigue Damaged Steel Structures. IIW Collection, Springer. Available online: https://link.springer.com/book/9783031801457.
33. (2024, October 01). Repair of Bridge Structural Steel Elements Manual (Release 1.0). Technical Standards Branch. Alberta Transportation. Available online: http://www.transportation.alberta.ca/content/doctype30/production/rprbrstrstel.pdf.
34. Crack-growth arrest by redirecting crack growth by drilling stop holes and inserting pins into them10.1016/j.engfailanal.2008.06.009 ↗
35. Fatigue damage repair: A comparison of some possible methods10.1016/S0142-1123(96)00029-1 ↗
36. Effects of expanded and nonexpanded hole on the delay of arresting crack propagation for aluminum alloys10.1016/S0921-5093(00)00805-4 ↗
37. A crack-growth arresting technique in aluminum alloy10.1016/j.engfailanal.2007.02.005 ↗
38. Crack stop holes in steel bridge decks: Drilling method and effects10.1007/s11771-017-3649-8 ↗
39. Effects of stop hole on crack turning, residual fatigue life and crack tip stress field10.1007/s40430-020-02299-1 ↗
40. Probabilistic analysis of the effect of shot peening on the high and low cycle fatigue behaviors of AA 7050-T745110.1016/j.ijfatigue.2018.02.029 ↗
41. (2022). Standard Test Method for Measurement of Fatigue Crack Growth Rates (Standard No. ASTM E647-22).
42. Numerical analysis of compliance and fatigue life of the CCC specimen10.1016/j.ijfatigue.2022.107496 ↗
43. Prediction of non-propagating cracks10.1016/0013-7944(79)90081-X ↗
44. Algorithms and Strategies for Treatment of Large Deformation Frictional Contact in the Numerical Simulation of Deep Drawing Process10.1007/s11831-008-9018-x ↗
45. Plastic instability under plane stress10.1016/0022-5096(52)90002-1 ↗
46. A mathematical representation of the multiaxial Bauschinger effect10.3184/096034007X207589 ↗
47. Influence of specimen orientation on fa-tigue crack growth in 7050-T7451 and 2050-T8 aluminium alloys10.1016/j.ijfatigue.2022.107136 ↗
48. Room-temperature low-cycle fatigue and fracture behaviour of asymmetrically rolled high-strength 7050 aluminium alloy plates10.1016/j.ijfatigue.2020.105919 ↗
49. Sharp, P.K., Byrnes, R., and Clark, G. (2024, October 01). Examination of 7050 Fatigue Crack Growth Data and Its Effect on Life Prediction. Available online: https://www.scribd.com/document/406623770/Experimental-Studies-Into-Short-Crack-Growth.
50. Effects of the specimen form on high cycle fatigue properties of 7050-T7451 and 2524-T3 aluminum alloys. IOP Conference Series
51. Cumulative damage in fatigue
52. Fatigue crack initiation life prediction for aluminium alloy 7075 using crystal plasticity finite element simulations10.1016/j.mechmat.2014.11.004 ↗
53. Differences in fatigue crack growth between L-T and S-T orientations in an aluminium 7050-T7451 plate10.1111/ffe.14067 ↗
54. Effect of load blocks on fatigue crack growth10.1016/j.ijfatigue.2022.107001 ↗
55. Numerical prediction of fatigue crack growth based on cumulative plastic strain versus experimental results for AA6082-T610.1007/s10704-022-00680-w ↗