journal article·2026-02-20Open access

Effect of Waste Composite Plate Powders on the Mechanical, Durability and Microstructural Properties of Self-Compacting Mortars

Yusuf Yıldırım, Alirıza İlker Akgönen, Serkan Etli

Materials· Volume 19· Issue 4

Abstract

This study investigates the effects of artificial plate powders with different compositions on the durability, physical, mechanical, and microstructural properties of self-compacting mortar (SCM). Waste quartz-based composite plate fragments and waste cultured marble pieces were ground into fine powders, and the resulting quartz-based plate powder (WQP) and cultured marble powder (WMP) were used as filler materials to partially replace cement at replacement levels of 0%, 5%, 10%, 15%, 20%, and 25% by mass. The workability of fresh mortars was evaluated using the mini slump flow test in accordance with EFNARC guidelines, while hardened specimens were tested for porosity, capillary water absorption, abrasion resistance, flexural strength, and compressive strength. In addition, specimens with a 25% replacement ratio that were exposed to temperatures of 300 °C, 600 °C, and 900 °C underwent mechanical testing, and their microstructures were analyzed using SEM and XRD. The results indicated that increasing replacement ratios generally reduced workability and mechanical strength, while increasing porosity and water absorption. However, low replacement levels slightly enhanced flexural strength due to the filler effect. SEM and XRD analyses revealed that the quartz in WQP maintained high thermal stability, and mortars containing WQP exhibited a denser, more coherent, and more homogeneous microstructure. Overall, the findings demonstrate that waste-based plate powders can serve as sustainable fillers in SCM, offering environmental benefits while maintaining acceptable mechanical and microstructural performance.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Building materials and conservation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Andırın Vocational School, Kahramanmaraş Sütçü İmam University, Kahramanmaraş 46410, Türkiye

Department of Civil Engineering, Kahramanmaraş Sütçü İmam University, Kahramanmaraş 46100, Türkiye

References (28)

Show source-provided references
1. Khaiyum, M.Z., Sarker, S., and Kabir, G. (2023). Evaluation of carbon emission factors in the cement industry: An emerging economy context. Sustainability, 15.10.3390/su152115407 ↗
2. Cement plant emissions and health effects in the general population: A systematic review10.1016/j.chemosphere.2018.11.088 ↗
3. Environmental impact of cement production and solutions: A review10.1016/j.matpr.2021.02.212 ↗
4. Eco-efficient cements: Potential economically viable solutions for a low-CO2 cement-based materials industry10.1016/j.cemconres.2018.03.015 ↗
5. Multiscale characterization of geopolymers modified with alkali-catalyzed nano-silica: Effects on dispersion and mechanical properties10.1016/j.cemconcomp.2025.106324 ↗
6. Evaluation of natural stone production and processing plant wastes
7. Sagar, G.S., Mukthi, S., and Mehta, V. (2025). Analyzing compressive, flexural, and tensile strength of concrete incorporating used foundry sand: Experimental and machine learning insights. Arch. Comput. Methods Eng., 1–27.10.1007/s11831-025-10405-6 ↗
8. Investigation of mechanical properties of granite waste sludge and sepiolite substituted self-compacting mortars
9. Benjeddou, O., and Alwetaishi, M. (2021). Valorization of powder obtained from marble sludge waste and its suitability as a mineral filler. Crystals, 11.10.3390/cryst11060619 ↗
10. Self compacting concrete: Use of waste marble powder as filler material
11. Karakurt, C., and Dumangöz, M. (2022). Rheological and durability properties of self-compacting concrete produced using marble dust and blast furnace slag. Materials, 15.10.3390/ma15051795 ↗
12. Exploring the potential of waste marble powder as a sustainable substitute to cement in cement-based composites: A review10.1016/j.conbuildmat.2023.132887 ↗
13. Recycling of marble and granite waste in concrete by incorporating nano alumina10.1016/j.conbuildmat.2023.134456 ↗
14. Elevated temperature performance of cementitious mortars containing pumice, barite, and basalt powder10.1016/j.jobe.2023.107552 ↗
15. Huseien, G.F., Sam, A.R.M., Faridmehr, I., and Hajmohammadian Baghban, M. (2021). Performance of epoxy resin polymer as self-healing cementitious materials agent in mortar. Materials, 14.10.3390/ma14051255 ↗
16. Examination of porcelain polishing residue as a supplementary cementitious materials10.1016/j.jobe.2025.112897 ↗
17. A Study on sustainable foam concrete with waste polyester and ceramic powder: Properties and durability10.1016/j.jobe.2024.110253 ↗
18. Evren, Ö. (2018). Manufacture and Characterization of Glass Fiber Reinforced Artificial Marble Blocks from Marble Wastes. [Master’s Thesis, Muğla Sıtkı Koçman University].
19. (2011). Admixtures for Concrete, Mortar and Grout–Part 2: Concrete Admixtures–Definitions, Requirements, Conformity, Marking and Labelling (Standard No. TS EN 934-2).
20. Sika (2025, June 25). Sika® ViscoCrete® ACE 450—High Range Water Reducing, Superplasticizer for Concrete. Technical Data Sheet. Sika Türkiye. Available online: https://tur.sika.com/dms/getdocument.get/fa5e6b94-94d6-4800-b614-2289dbca5ccd/sika-viscocrete-ace450.pdf.
21. (2015). Fire-Resistance Tests—Elements of Building Construction (Standard No. ISO 834).
22. (2003). Standard Test Methods for Fire Tests of Building Construction and Materials (Standard No. ASTM E119).
23. (2009). Methods of Testing Cement—Part 1: Determination of Strength (Standard No. TS EN 196-1).
24. Investigation of the variation of mechanical and durability properties of elements manufactured with rubber substituted SCMs with element height10.1016/j.conbuildmat.2024.136300 ↗
25. (2013). Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic Cement Concretes (Standard No. ASTM C1585-13).
26. Borucka-Lipska, J., Brzozowski, P., Błyszko, J., Bednarek, R., and Horszczaruk, E. (2020). Effects of elevated temperatures on the properties of cement mortars with the iron oxides concentrate. Materials, 14.10.3390/ma14010148 ↗
27. Petkova, V., Stoyanov, V., Kostova, B., Kostov-Kytin, V., Kalinkin, A., Zvereva, I., and Tzvetanova, Y. (2021). Crystal-chemical and thermal properties of decorative cement composites. Materials, 14.10.3390/ma14174793 ↗
28. Dudek, M., and Sitarz, M. (2020). Analysis of changes in the microstructure of geopolymer mortar after exposure to high temperatures. Materials, 13.10.3390/ma13194263 ↗