journal article·2026-02-24Open access

Experimental Investigation on the Fracture Behavior of Basalt Fiber-Reinforced Shotcrete

Junbo Guo, Wei Shi, Kun Wang, Lingze Li, Dingjun Xiao

Materials· Volume 19· Issue 5

Abstract

Basalt fiber-reinforced concrete is increasingly being used in shotcrete support systems for rock mass excavation engineering due to its superior mechanical properties and durability. Rapid freeze–thaw cycling tests were performed to simulate freeze–thaw conditions in order to meticulously investigate the dynamic and static fracture behaviors of basalt fiber-reinforced concrete in freeze–thaw environments. Then, utilizing a Split Hopkinson Pressure Bar (SHPB) system and rock testing equipment, dynamic and static fracture tests were performed on developed Mode I, mixed-mode I/II, and Mode II platform Brazilian disk specimens. Under freeze–thaw conditions, the dynamic and static fracture propagation velocities of specimens with diverse crack propagation modes were determined. Based on this, LS-DYNA numerical simulations were used to perform inverse evaluations of crack propagation processes in specimens with varied fracture modes and Mode I fracture specimens with variable basalt fiber contents. We were able to calculate the effective stress field distributions during crack propagation with dynamic loading. The data indicate that different fracture modes present significantly distinct crack propagation issues. Pure Mode I fracture specimens exhibit the most straightforward crack propagation, with a maximum effective stress of roughly 25 MPa after crack penetration. With a maximum effective stress of around 31 MPa following crack penetration, the mixed-mode I/II fracture specimens exhibit considerable propagation difficulties. Mode II fracture specimens are the hardest to propagate after crack penetration because of their maximum effective stress of 64 MPa. Additionally, the optimal basalt fiber content was determined to be in the range of 0.35% to 0.45%, at which the concrete exhibited the best fracture toughness and freeze–thaw resistance. Furthermore, the evolution characteristics of the displacement of the crack tip opening under different fracture modes are revealed. A theoretical basis for stability analysis and design of excavation engineering structures under dynamic stress and associated freeze–thaw conditions is provided by the study’s findings.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Rock Mechanics and Modeling · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

The Third Engineering Bureau Co., Ltd. of China An’neng Construction Group, Chengdu 611130, China

Department of Mining Engineering, School of Environment and Resources, University of Science and Technology Southwest, Mianyang 621010, China

Funding

Ordos Science & Technology Plan · Ltd. of China An’neng Construction Group

References (42)

Show source-provided references
1. Fracture Mechanisms in Bio-Inspired Bouligand Continuous Basalt Fiber-Reinforced Polylactic Acid Composites Fabricated Via Additive Manufacturing10.1016/j.coco.2026.102724 ↗
2. Mechanical Behavior and Constitutive Relationship of Basalt Fiber Reactive Powder Concrete Under Impact Loading
3. Mechanical and Microstructural Characterization of Graphene Dispersed Basalt Fiber Reinforced Polymeric Composites10.1016/j.jmrt.2025.12.235 ↗
4. Sustainable Ultra-High-Performance Basalt Fiber-Reinforced Geopolymer Concrete Incorporating Carbon Nanotubes and Treated Recycled Aggregates
5. Study On Properties of Basalt Fiber Coal Gangue Concrete Modified by Supplementary Cementitious Materials: Mechanics, Durability, Microstructure10.1016/j.jobe.2025.112271 ↗
6. Investigating the Impact of Freezing and Thawing Cycles On the Dynamic Fracture Properties of Red Sandstone Subjected to Impact Loading10.1016/j.tafmec.2025.105006 ↗
7. Comparison of the Effect of Freezing-Thaw Cycles On the Fracture Resistance of Hma and Sma Asphalt Mixtures Under Different Loading Modes10.1016/j.conbuildmat.2025.144584 ↗
8. Assessment of Basalt Fiber and Gelling Enhancement Effects On Mixed Mode I/III Fracture Performance of the Mortar Composites10.1016/j.tafmec.2024.104303 ↗
9. Effect of Basalt Fibers and Silica Fume On the Mechanical Properties, Stress-Strain Behavior, and Durability of Alkali-Activated Slag-Fly Ash Concrete10.1016/j.conbuildmat.2024.135440 ↗
10. Evaluation of Long-Term Fracture Behavior of Hot Mix Asphalt Modified with Nano Reduced Graphene Oxide (Rgo) Under Freeze–Thaw Damage and Aging Conditions10.1016/j.conbuildmat.2023.130875 ↗
11. Influences of Freeze–Thaw Cycles (FTC) On Tensile Properties and Mixed-Mode I/II Fracture Response of Epoxy Resin Materials10.1016/j.tafmec.2024.104830 ↗
12. Laboratory Measurement of Sonic (1–20 Khz) P-Wave Velocity and Attenuation During Melting of Ice-Bearing Sand10.1029/2024JB030465 ↗
13. Microscopic Damage and Deterioration of Carbonaceous Slate in Cold Region Subjected to Freeze-Thaw Cycles10.1016/j.jrmge.2025.01.006 ↗
14. Microstructure and Energy Evolution of Cyan Sandstone with Prefabricated Fractures at Different Angles During Failure Under Freeze–Thaw Cycles10.1016/j.tust.2025.107149 ↗
15. Failure Analysis and Enhancement Measures of Wet Shotcrete Support During Cold Periods in Mining10.1016/j.conbuildmat.2024.139769 ↗
16. Freeze-Thaw Cycle Characteristics of Graphite Tailing Concrete and Steel Fiber Reinforced-Graphite Tailing Concrete10.1016/j.conbuildmat.2025.140006 ↗
17. Micromechanics-Based Thermo-Hydro-Mechanical Model for Air-Entrained Porous Materials Subjected to Freezing-Thawing Cycles10.1016/j.jrmge.2024.11.055 ↗
18. Flexural and Split Tensile Strength of Concrete with Basalt Fiber: An Experimental and Computational Analysis10.1016/j.conbuildmat.2024.134936 ↗
19. Effect of Interlaminar Basalt Fiber Veil Reinforcement On Mode I Fracture Toughness of Basalt Fiber Composites10.1002/pc.28103 ↗
20. Workability & Mechanical Properties of the Single and Hybrid Basalt Fiber Reinforced Volcanic Ash-Based Cement Mortars After Freeze–Thaw Cycles10.1016/j.istruc.2023.01.062 ↗
21. Dynamic Mixed Mode I–II Fracture of Notched Brazilian Discs Fabricated by Additive Manufacturing10.1016/j.ijimpeng.2025.105290 ↗
22. The Effect of Wetting-Drying/Freezing-Thawing Cycles On Properties of Non-Air Entrained Fly Ash Substituted Cement-Based Composites10.1016/j.ceramint.2022.11.294 ↗
23. Mixed Mode Fracture Parameters and Fracture Characteristics of Diorite Using Cracked Straight through Brazilian Disc Specimen10.1016/j.tafmec.2022.103682 ↗
24. Sequential Determination of Dynamic Initiation and Propagation Toughness of Rock Using an Experimental–Numerical–Analytical Method10.1016/j.engfracmech.2015.04.025 ↗
25. Fracture Analysis of 3D-Printed Stereolithography Parts Using the Brazilian Disc with a Central Notch10.1016/j.tafmec.2025.105312 ↗
26. Correction of Dynamic Brazilian Disc Tensile Strength of Rocks Under Preloading Conditions Considering the Overload Phenomenon and Invoking the Griffith Criterion10.1016/j.jrmge.2022.10.011 ↗
27. Rock Fracture Toughness Study Using Cracked Chevron Notched Brazilian Disc Specimen Under Pure Modes I and II Loading—A Statistical Approach10.1016/j.tafmec.2013.11.008 ↗
28. Measurement of Mode I and Mode II Rock Dynamic Fracture Toughness with Cracked Straight through Flattened Brazilian Disc Impacted by Split Hopkinson Pressure Bar10.1016/j.engfracmech.2011.06.004 ↗
29. A Finite Element Analysis for Using Brazilian Disk in Split Hopkinson Pressure Bar to Investigate Dynamic Fracture Behavior of Brittle Polymer Materials10.1016/j.polymertesting.2006.06.003 ↗
30. Tests and numerical simulation for splitting tensile fracture properties of CSTFBD concrete specimen under impact loading
31. Pei, G., Xiao, D., Zhang, M., Jiang, J., Xie, J., Li, X., and Guo, J. (2024). Study On the Dynamic Fracture Properties of Defective Basalt Fiber Concrete Materials Under a Freeze–Thaw Environment. Materials, 17.10.3390/ma17246275 ↗
32. Degradation of Mechanical Properties and Microstructure Evolution of Basalt-Carbon Based Hybrid FRP Bars in Real Seawater and Sea-Sand Concrete10.1016/j.compositesb.2023.111163 ↗
33. A 3D Multi-Phase-Field Model for Orientation-Dependent Complex Crack Interaction in Fiber-Reinforced Composite Laminates10.1016/j.engfracmech.2024.110097 ↗
34. (2008). Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Standard No. ASTM C666/C666M-15).
35. Testing of Mode-I Fracture Toughness of Sandstone Based On the Fracturing Mechanism of an Explosion Stress Wave10.1007/s00603-022-03047-8 ↗
36. Study of testing method for dynamic initiation toughness of blue sandstone under blasting loading
37. Crack Arrest Characteristics and Dynamic Fracture Parameters of Moving Cracks Encountering Double Holes Under Impact Loads10.1016/j.ijimpeng.2024.105158 ↗
38. Investigating the Propagation Behavior of Cracks Outside Tunnel Under Impact Conditions10.1016/j.istruc.2025.108613 ↗
39. A Modified Model for Calculating Crack Tip Opening Displacement (CTOD) Considering Fracture Process Zone (FPZ) in Rock10.1007/s40948-024-00779-5 ↗
40. Numerical Calculation of ΔCTOD to Simulate Fatigue Crack Growth Under Large Scale Viscoplastic Deformations10.1016/j.engfracmech.2023.109064 ↗
41. Further Investigation of J-CTOD Relationship for Clamped SET Specimens Based On Finite Element Analyses—Part I: Homogeneous Materials10.1016/j.tafmec.2022.103523 ↗
42. On the Experimental Estimation of CTOD Fracture Parameter Using SE(T) Specimens Based upon Only One Clip Gauge Measurement10.1016/j.engfracmech.2021.107856 ↗