journal article·2015-10

The effect of surface treatment and topography on corrosion behavior of EN 1.4404 stainless steel

R. Lage, P. Møller, H. E. Fallesen

Materials and Corrosion· Volume 66· Issue 10
Publisher page

Abstract

Corrosion properties of EN 1.4404 (316L) stainless steel with different applied surface treatment, were studied in NaCl solution using cyclic polarization. Observed properties were related to the specific topography of each surface by scanning electron microcopy and cross‐section analysis. Average roughness was measured to evaluate the usability for this parameter to be used in assessment of corrosion resistance. Increased surface roughness and the existence of crevices resulted in overall deterioration of corrosion resistance, whereas more smooth and level topographies displayed general improvement. By analyzing the characteristic geometry of the typographies produced, the correlation between the varying corrosion properties and surfaces is determinable. In continuation hereof, the utilization of average roughness values (Ra) as an isolated parameter, were found not to be sufficient for the assessment of corrosion resistance. Critical surface geometries with large impact on corrosion properties is not conveyed adequately by Ra, and thereby prevents sufficient differentiation between the actual surface properties.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Division of Materials Science and Engineering Department of Manufacturing and Management The Technical University of Denmark Anker Engelunds Vej 1 DK‐2800 Kgs. Lyngby (Denmark)

Department of Systems Biology The Technical University of Denmark DK‐2800 Kgs. Lyngby (Denmark)

IPU Bio and Food Technology DK‐2800 Kgs. Lyngby (Denmark)

References (17)

Show source-provided references
1. 10.5006/1.329360310.5006/1.3293603 ↗
2. 10.1016/S0010-938X(96)00066-210.1016/S0010-938X(96)00066-2 ↗
3. 10.1098/rsta.1992.011410.1098/rsta.1992.0114 ↗
4. 10.1080/0950083920822927410.1080/09500839208229274 ↗
5. 10.1016/0010-938X(93)90133-210.1016/0010-938X(93)90133-2 ↗
6. 10.1149/1.141650310.1149/1.1416503 ↗
7. 10.1016/S0010-938X(97)00072-310.1016/S0010-938X(97)00072-3 ↗
8. 10.1002/maco.20040381710.1002/maco.200403817 ↗
9. 10.1002/maco.20120674910.1002/maco.201206749 ↗
10. 10.1002/maco.20040384610.1002/maco.200403846 ↗
11. 10.1016/S0010-938X(01)00039-710.1016/S0010-938X(01)00039-7 ↗
12. 10.1002/maco.20130705710.1002/maco.201307057 ↗
13. 10.4028/www.scientific.net/MSF.44-45.31310.4028/www.scientific.net/MSF.44-45.313 ↗
14. 10.1021/la00078a01010.1021/la00078a010 ↗
15. Møller P. · 2014
16. 10.1021/j150550a00510.1021/j150550a005 ↗
17. 10.1016/j.corsci.2012.06.03110.1016/j.corsci.2012.06.031 ↗