journal article·2004-12-28

Vent Location Optimization Using Map-Based Exhaustive Search in Liquid Composite Molding Processes

Ali Gokce, Suresh G. Advani

Publisher page

Abstract

Abstract In liquid composite molding (LCM) processes, the resin is injected into the mold cavity, which contains preplaced reinforcement fabrics, through openings known as gates, while the displaced air leaves the mold through openings called vents. Under nominal conditions, the last points to fill are chosen as vent locations. However, due to imperfect preform cutting and placement, gaps and channels may form along the edges and curvatures in a mold, offering a path with less resistance for resin flow. The faster advance of resin through these gaps and channels, a common disturbance known as racetracking, will cause the last filled regions to vary, which complicates the vent selection process. In this study, probabilistic racetracking modeling is used to capture last-filled region distribution over the mold geometry. Success criteria for mold filling are defined in terms of dry spot tolerances, and vent fitness maps, which display potential vent locations, are created. Next, exhaustive search algorithm is coupled with vent fitness maps to determine optimal vent configurations. The map-based exhaustive search is demonstrated on three geometries and results are compared with existing combinatorial search results. The performance of the optimal vent configurations is evaluated in a virtual manufacturing environment. Sensitivity analyses are conducted to determine the influence of optimization parameters on the results.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Injection Molding Process and Properties · Manufacturing Process and Optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Advani S.G. · 1994 · 465
2. 10.1002/pc.75016060210.1002/pc.750160602 ↗
3. 10.1002/pc.1058810.1002/pc.10588 ↗
4. Heitzmann, K.F. Determination of In-plane Permeability of Woven and Nonwoven Fabrics. Master's thesis. University of Illinois at Urbana-Champaign.
5. 10.1002/pc.1065810.1002/pc.10658 ↗
6. Bruschke M.V. · 1991
7. Phelan F.R. · Composites Part A · 1996 · 2710.1016/1359-835X(95)00016-U ↗
8. 10.1007/BF0061533210.1007/BF00615332 ↗
9. 10.1016/S0045-7949(99)00174-110.1016/S0045-7949(99)00174-1 ↗
10. Spaid M. · Physics of Fluid · 1997 · 9
11. 10.1103/PhysRevE.53.74310.1103/PhysRevE.53.743 ↗
12. 10.1002/pc.75014050410.1002/pc.750140504 ↗
13. 10.1002/pc.75015040610.1002/pc.750150406 ↗
14. 10.1002/pen.76026201310.1002/pen.760262013 ↗
15. Pavel, Nedanov. Permeability Characterization of Fibrous Porous Media. Master's thesis. University of Delaware.
16. Han, K., Wu, C.H. and Lee, L.J. 1993. In Proceedings of Ninth Annual ASM-ESD Advanced Composite Conference. 1993, Michigan. Characterization and Simulation of Resin Transfer Molding—Racetracking and Dry Spot Formation,
17. Leek, R., Carpenter, G., Donnellan, T. and Phelan, F. 1993. In Proceedings of the 25th International SAMPE Technical Conference. Oct1993. Simulation of Edge Flow Effects in Resin Transfer Molding, pp.233–245.
18. 10.1002/pc.1028010.1002/pc.10280 ↗
19. 10.1002/pc.1007910.1002/pc.10079 ↗
20. 10.1016/S1359-835X(97)00120-610.1016/S1359-835X(97)00120-6 ↗
21. 10.1016/S0266-3538(99)00077-910.1016/S0266-3538(99)00077-9 ↗
22. Chaneske, J., Jayaraman, K., Norman, D. and Robertson, R. 2000. Proceedings of International SAMPE Symposium and Exhibition. May2000, Long Beach, CA. Effects of Preform Architecture on Racetracking in Liquid Molding, pp.954–966.
23. 10.1081/AMP-12001890910.1081/AMP-120018909 ↗
24. Demirci H.H. · Journal of Materials Processing and Manufacturing Science · 1995 · 3 · 409
25. Berker B. · Journal of Materials Processing and Manufacturing Science · 1997 · 6 · 81
26. 10.1106/E54L-M81L-XXKB-M8DN10.1106/E54L-M81L-XXKB-M8DN ↗
27. Sozer, E.M., Bickerton, S. and Advani, S.G. 1999. Proceedings of Flow Processes in Composite Materials (FPCM). July1999, Plymouth, UK. Modeling and Control of Liquid Composite Mold Filling Process, pp.109–124.
28. Barooah, P. and Sun, J.Q. 2000. Proceedings of the American Control Conference. June2000, Chicago, IL. Flow Control in Resin Transfer Molding with Switching and Feedback Strategies, Vol. 6,10.1109/ACC.2000.877028 ↗
29. 10.1016/S1359-835X(01)00013-610.1016/S1359-835X(01)00013-6 ↗
30. 10.1115/1.155916210.1115/1.1559162 ↗
31. 10.1002/pc.1034410.1002/pc.10344 ↗
32. 10.1002/pc.1057110.1002/pc.10571 ↗
33. 10.1002/pc.75011061310.1002/pc.750110613 ↗