Multiphysics simulation and experimental investigation of microtool fabricated by EMM
Source abstract
Abstract
Due to the continuous demand for miniature products, demand for microtool increases. Various conventional and non-conventional methods have been employed for the fabrication of microtool. In this paper, electrochemical micromachining (EMM) is used for the fabrication of microtool as it offers good accuracy, no heat generation, contactless process, no tool wear and good surface finish. The microtool of different shape and sizes are fabricated from Tungsten tool having initial diameter of 500 µm using the two different techniques. In the first technique, the tool is placed inside the pre-made hole in stainless steel (SS) plate and the effect of tool rotation is analyzed. In the second technique, the tool is kept adjacent to SS plate and the analysis is based on the interelectrode gap (IEG) during machining. COMSOL® Multiphysics software is used to create a 2D model to study the variation of current density distribution in the interelectrode gap. First technique with tool rotation results in conical microtool with good surface finish and second technique results in cylindrical microtool with diameter less than 100 µm. Simulation results are validated with the experimental results with an error below 15%.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Indian Institute of Technology Guwahati, Guwahati Assam-781039, India
Funding
Not applicable
References (26)
Show source-provided references
1. 10.1080/10426914.2013.86440710.1080/10426914.2013.864407 ↗
2. 10.1016/j.jmapro.2018.10.03810.1016/j.jmapro.2018.10.038 ↗
3. 10.1088/1757-899X/804/1/01201110.1088/1757-899X/804/1/012011 ↗
4. 10.1177/251659841989582810.1177/2516598419895828 ↗
5. 10.1080/10426914.2018.153258210.1080/10426914.2018.1532582 ↗
6. 10.1177/095440892093455010.1177/0954408920934550 ↗
7. 10.1080/10426914.2011.55190510.1080/10426914.2011.551905 ↗
8. 10.1016/S0924-0136(03)00064-510.1016/S0924-0136(03)00064-5 ↗
9. 10.1016/0022-0728(88)80042-110.1016/0022-0728(88)80042-1 ↗
10. Saha S. · Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. · 2020 · 095440542095896
11. 10.1007/s00170-017-1150-z10.1007/s00170-017-1150-z ↗
12. 10.1016/S0924-0136(03)00760-X10.1016/S0924-0136(03)00760-X ↗
13. 10.1177/095440541349700710.1177/0954405413497007 ↗
14. 10.1007/s00170-013-4896-y10.1007/s00170-013-4896-y ↗
15. 10.1007/s10800-019-01380-510.1007/s10800-019-01380-5 ↗
16. 10.1007/978-981-15-0124-1_5110.1007/978-981-15-0124-1_51 ↗
17. 10.1080/10426914.2020.175292010.1080/10426914.2020.1752920 ↗
18. 10.1016/j.surfcoat.2016.05.08810.1016/j.surfcoat.2016.05.088 ↗
19. Kunar S. · 227
20. 10.1007/s00170-016-9700-310.1007/s00170-016-9700-3 ↗
21. Hackert-Oschatzchen M. · 2012
22. Hackert-Oschätzchen M. · 2013
23. 10.1016/j.elecom.2013.12.02010.1016/j.elecom.2013.12.020 ↗
24. Hackert-Oschätzchen M. · 2016 · 2
25. 10.1007/s00170-012-4062-y10.1007/s00170-012-4062-y ↗
26. 10.3390/mi1102011810.3390/mi11020118 ↗